Search Documents

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By Andrzej Wala

Constantly increasing demand for energy materials and metal ores brought about tremendous progress in mining techniques which are characterised by a high degree of mechanization and concentration of works. One of the recent trends in underground mining mechanization is connected with an application of heavy machines with diesel engines [l],[2]. The introduction of diesel engines in mining all over world caused not only improvement in economic conditions but also the necessity to prevent contamination of air in the mine by toxic agents in diesel exhaust emissions. A generally used way of eliminating exhaust gases is proper ventilation of the cross cut by means of providing permanent exchange of air that would guarantee in every point of the cross cut and in every moment the decay in concentration of exhaust gases beyond threshold limit [3][4][5][6][7][8][9][10]. The present paper is an attempt to define a mathematical model describing the changes of concentration in cross cut face to which fresh air is distributed by ventilators and tubes in a forcing way. Obtained model should offer its practical adaptability to engineering calculation of the amount of fresh air needed for diluting and eliminating exhaust gases beyond threshold limit. Justness of these models has been confirmed by investigation of the growth of nitrogen dioxide concentration in air environment in some cross cut faces of Kiirunavaara iron ore mine in Kiruna (Sweden).

Jan 1, 1980

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By Ward Sumner

The Jones Hill prospect is a Proterozoic age, volcanogenic, semi-massive to massive sulfide deposit. The deposit is located on the western edge of the Pecos greenstone belt in the southern Sangre de Cristo Mountains of northern New Mexico. The prospect is found in a block (West Block) of meta- igneous rocks, primarily diabase, metavolcanic rocks, and metasedimentary rocks (fig. 1). This assemblage is typical of lithologies found in the greenstone belt. Metamorphic grade is greenschist to lower amphibolite. The West Block is bound- ed on the west by Proterozoic age (1.7-1.4 b.y. by Rb/Sr), granitic plutons collectively called the Embudo granite, and on the east by Paleozoic sedimentary rocks, primarily sandstones, shales, and limestones of Mississippian and Pennsylvanian age. The mineralization occurs in a single horizon which has been overturned and cut into two blocks by a high-angle reverse fault (fig. 2). The mineralized horizon is found at the contact of felsic metavolcanic and rnetavolcaniclastic rocks with overlying intermediate metasedimentary rocks. The local stratigraphic sec- tion from bottom to top is as follows: 1) porphyroblastic quartz- sericite schist (originally a rhyolitic, subvolcanic intrusive); 2) quartz-sericite-chlorite-biotite schist (felsic metavolcanic and metavolcaniclastic rocks); 3) chlorite-talc-biotite-sulfide schist (altered felsic metavolcanic rocks); 4) carbonate-quartz-sulfide [ ] chlorite-tremolite-talc schist (mineralized exhalite); 5) quartz- chlorite schist (silicified tuff); and 6) amphibole-chlorite-feldspar- biotite schist (occasional mafic to intermediate metavolcanic flows).

Jan 1, 2013

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By T. P. Weldum

INTRODUCTION Cleveland-Cliffs' operations in Michigan have been utilizing fully autogenous grinding for over four decades. This is but one of the key characteristics of the iron ore processing method that was developed for the extremely fine grained, low grade deposits of the region. Liberation size of the hematite and magnetite ranges from about 30 to less than 1 micron. Typical grinding fineness target to achieve silica grade in the concentrate is 80 to 90% passing 25 microns, or a P80 of approximately 20 microns. After primary grinding, the magnetite ore is first upgraded by rougher magnetic separation. It is then ground to final product size, sent through thickener-sizers utilizing selective flocculation, upgraded again by finisher magnetic separation, and then brought to final silica grade by reverse amine flotation. Hematite ore follows essentially the same route, less the magnetic separation stages. Concentrate is filtered and pelletized, along with con- trolled additions of fluxstone, to ready it for shipping. Iron ore pellets on the water of the Great Lakes have a value of approximately 1.5 cents per pound. GRINDING PROCESS DESCRIPTION Details of the Empire magnetite grinding process flowsheet have been presented by Greenwood and Rajala (1992), and more recently by Rose et al. (2002). The Tilden comminution process for either magnetite or hematite is essentially identical, with the exception of some variations in the excess pebble treatment methods (McIvor and

Jan 1, 2004

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

As orebodies being mined globally are of ever-decreasing grades, the focus on the concentration process has moved increasingly to the challenges faced in management of the gangue minerals. This is especially so in the flotation of platinum group minerals (PGMs), where head grades are typically in the region of 4–7 g/t. Hence, in PGM operations, a typical recovery of about 80 percent requires depressing about 85 percent of the gangue minerals. In a flotation cell the main control parameters are reagent type and dosage, froth depth and air addition rate. This paper reviews research projects carried out over an extended period aimed at optimizing the depression of gangue minerals: both those that are naturally floatable and those, such as chromite, that are entrained.  This has involved comparing the two major depressants used in the industry — guar and carboxymethylcellulose (CMC) — in the depression of the relevant gangue minerals, as well as investigating their consequent effect on the behavior of the froth phase. Because most PGM flotation plants treat the ore as if all the PGMs are associated with sulfides, copper sulfate is widely used as an activator, but this can also lead to inadvertent activation of gangue minerals. Finally, chromite levels must be kept below 3–5 percent to avoid any negative effects on smelter performance, and thus it is important to reduce chromite recovery which mainly occurs due to entrainment through, for example, froth depth control.   

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator&apos;s location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By S. T. Murray

The European industrial minerals industry and its markets are largely self-sufficient. The companies who are members of the Industrial Minerals Association (IMA-Europe) number around 150 contributing 5 billion Euros to the EU?s GDP and range in size from global publicly quoted corporations to small family owned private companies. Their means and capability to implement sustainable development vary considerably. However the leading companies provide an excellent set of best practices, which IMA as a trade association with recognised core competencies in the field of sustainable development is ideally placed to promulgate throughout its membership. As an active participant in the EU Voluntary Scheme for SDI reporting IMA is not only working to increase the level of response to the SDI questionnaire but is also developing with its members a new sustainable development charter which its members will voluntarily adopt as a guiding principle for their implementation of sustainable development This work will be a consultative process involving all IMA?s section members as well as other trade associations, NGOs and MEPs. Public awareness of the benefits of minerals and their contribution to sustainable development has been raised by IMA?s awareness campaign now being followed by a more targeted programme aimed at MEPs. Further work in the future will consider product stewardship and life-cycle analysis. IMA is already positioning itself with the help of its members to assimilate the minerals industry of the accession territories in the sustainable development process.

Jan 1, 2003

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal&apos;s mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By D. E. Ranta, John G. Stone

One of the steps in an ore reserve estimate is customarily a rigorous calculation of the in situ grade of the orebody itself. The result of this calculation is usually reduced by some purely arbitrary factor to force the calculation to agree with the observed grade of ore actually mined. The failure of the calculation to realistically depict the grade of ore actually extracted is in many instances not the result of either an incorrect calculation procedure or of sloppy mining practice, but is a direct consequence of unsuspected irregularities in the contact between the orebody and the surrounding wall rock. A pattern of holes spaced at 1.5-3.Om foot intervals, drilled as part of a pre-development program, will often reveal that a presumed "regular&apos; ore/waste contact is, in fact, so highly irregular that it will be next to impossible to separate ore from waste during mining. In such an instance, &apos;fingers&apos; of waste projecting into the mining block will substitute for equal volumes of ore left outside the mining limits. As a result, the grade of material actually mined will be less than the grade envisioned for the orebody. The volume of waste substituting for ore in the mining block is about 0.4X, where X = the average error in projecting the ore/waste contact between alternate holes in the test pattern, and is expressed in units of volume per unit of area of the contact surface.

Jan 1, 1992

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By Cherie M. Tilley

The Stillwater Mining Co. of Nye, MT, is operating a platinum-palladium mine that requires an extensive system of footwall laterals to facilitate mine production. The 10-year mine plan calls for more than 48,300 lineal m (160,000 lineal ft) of footwall lateral. A rapid tunneling and raising system is necessary to sustain mine production schedules and achieve production goals. This article describes the results of using a Robbins 4.1-m-diam (l3.5ft-diam) tunnel boring machine (TBM) to develop the footwall laterals and a Robbins RBM-6SP raise boring machine to develop raises at the mine. The Stillwater Mining Co is a partnership between Chevron Resources Co. and Manville Corp. Chevron Resources is the managing partner. When the mine began production in September 1986, the owners were primarily concerned with the actual production of platinum and palladium, the grade minable and the amount that could be mined. As mine development and mine production proved feasible, the owners considered higher production levels. The Stillwater Mine is developed by a system of adits (known as footwall laterals) that are driven parallel to the ore bearing zone. This led mine officials to consider using a mechanical boring machine in the primary mine development. Previously, tunnel boring machines have not been used successfully in mining applications. Therefore, the owners decided to purchase a used machine to reduce the potential risk.

Jan 1, 1991