Search Documents

By J. A. Organiscak

Data on dust-control practices, mining conditions and occupational exposures were gathered for approximately 80 underground continuous mining units. Despite silica contents on dust samples in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/m3 on a majority of occupational dust samples, while the remainder had difficulty maintaining this level. These two sample sets were termed Group A operations and Group B operations, respectively. This data was compared to identify causes of high occupational silica dust exposures. Analyses of dust-control parameters and geologies revealed only minor differences between these two groups. However, subsequent comparisons of face ventilation design showed considerable differences in silica exposure and silica content between Group A and Group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber. This face ventilation system can benefit operations having difficulty controlling silica dust exposure and silica dust content. The collected data also showed that occupational samples from Group B operations possessed generally higher silica exposures and silica content than similar samples from Group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

Jan 1, 2002

By C. McLean, S. G. Kolb, A. J. Erickson, S. C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined with underground workings during 1980-82 by Esso Erz GmbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost-effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gamma probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross-cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 m thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1992

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

By R. C. Oberth, C. F. Lee, E. M. Taylor

INTRODUCTION Underground siting of nuclear power stations is drawing increasing attention in various parts of the world. Scandinavian countries took the early lead in this field because of their experience in the design and construction of underground hydroelectric stations and industrial plants, and because they have near-surface rock formations which are ideally suited for hosting large underground caverns. The world's first underground nuclear facilities were built in Norway (Halden) and Sweden (Agesta) and were commissioned in 1959 and 1963 respectively. Figure 1 summarizes the main features of these and two other small-scale European facilities. (1-4) American utilities and regulators are also for a variety of reasons assessing the benefits and penalties of underground siting. A recent study by Sandia Laboratories (contracted by the Nuclear Regulatory Commission (NRC) focussed on identifying potential safety benefits of underground siting. (5) Although the study concluded that underground plants would have improved containment for some accidents, as well as better external protection, NRC, in assessing the overall benefits and penalties, decided not to impose mandatory underground siting for nuclear stations. In June 1976, the California Legislature enacted a law which directed the California Energy Commission (CEC) to examine the issues concerned with underground siting of

Jan 1, 1979

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By G. R. Tostengard

Gold plant performance during the start-up period, which extends until capacity production is sustained, has a major impact on the internal rate of return and the net present value of gold projects regardless of mining and processing configurations. The start-up period experiences substandard production, extra expenses, and sometimes reduced recovery. This results in lost profits, a portion of which are recouped at the end of the life of the mine. Poor start-up performance can put projects into financial jeopardy. The gold mining industry regularly experiences start-ups ranging from good to poor. Problem areas, which affect start-up performance, include shortcomings in ore reserve sampling and testing, equipment design and installation, untrained plant operators, inability to cope with problems which arise, and organization of the maintenance program. An investment, equal to 0.5% to 1.0% of plant capital cost, in programs to prepare for start-up, in advance, is recommended. Investment in such a program will make a good start-up possible. Without it the best result which can normally be expected is a fair start-up. Developers of new gold mines are urged to compare the cost of this investment with the anticipated increase in project net present value. Funds for this investment should be included in feasibility studies.

Jan 1, 1988

By R. J. Sawyer

*An earlier version of this paper was presented at the IMM meeting, "Use of Cultivated Carbon in Extraction of Gold and Other Metals," held in London in January, 1983, and was subsequently published in Trans. IMM (Sect. C: Mineral Process. Extr. Metall.) in December, 1983. Reprinted with permission of The Institution of Mining and Metallurgy, London. INTRODUCTION This paper describes the development of the processing route for the Alligator Ridge Mine which commenced operation in 1980. It also reviews the modifications which have been made to improve operating efficiency during the three years that the mine has been in production. Alligator Ridge is located 70 miles Northwest of Ely, Nevada. The mine is a joint venture between Amselco and Nerco with Amselco acting as operator. The deposit consists of micron sized disseminated gold imbedded in siltstone. Although definitive conclusions have yet to be drawn as to the age and origin of the deposit, it is probable that it is young by geological standards, perhaps only 5 million years old. It is likely that the gold was brought to the surface by hot springs. As the superheated solutions rose through the porous siltstone, they redeposited minerals in the rock, forming the present ore bodies.

Jan 1, 1984

By Philippe Dumont

Presentation of the project Underground civil works to be performed They include two single track running tunnels and a service tunnel of a length of fifty kilometers . Many cross adits (180 adits) : to link the tunnels (53 cross passages), to relieve air super pressure from one tunnel to the other (87 piston ducts), to install technical adits (40 electrical rooms). Two cross-overs located at one third of the whole length, allow trains to shunt from one tunnel to the other so as to ensure one way traffic in case of emergency. Pumping stations allow water to be collected at the lowest point and pumped out. 1 Main features of the tunnels 1.1 The service tunnel This 4.8 m inner diameter gallery allows During civil works - front probing operations of the geological layers encountered (front and vertical probes). - lateral soil grouting that may be necessary to facilitate the boring of the two running tunnels . During operations - Maintenance and safety vehicles traffic - Fresh air supply to running tunnels - Fire protection and drainage system - Electricity supply and control and communication. The service tunnel has been bored with a 5.72 meter external diameter Robbins TBM for the undersea section, and a MITSUBISHI TBM for the land section.

Jan 1, 1991

By William M. PhD. Schafer

The net acid generation (NAG) pH method is an important analytical tool that supplements static and kinetic tests for assessment of the acid generation risk of rock samples. This method is useful because it is simple, rapid and cost-effective; it combines features of the static and kinetic tests; and it can be conducted at mine assay labs. The NAG pH test is particularly effective for operational testing programs used to classify, selectively handle, and route potentially acid-generating waste rock. The NAG pH procedure is based on a 24 hour oxidation of a pulverized rock sample with hydrogen peroxide and subsequent measurement of the sample's pH. If the NAG pH is below a critical value, determined empirically, then the sample has the potential to generate acid in the field. The critical NAG pH value is typically within the range of 3 to 4.5, but the exact relationship between NAG pH and potential acid generation should be determined individually for each mine site, based on comparison with results of acid base accounting, humidity cell tests, and mineralogical analyses. Calibration and use of the NAG test for predicting ARD risk at several mines are described in this paper.

Jan 1, 2000

By Lynn I. Kelley

Industrial-mineral production contributes on the order of CDN$1.5 billion per year to the economy of Saskatchewan, Canada. Potash is the primary industrial mineral produced in the province, followed by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium-chloride brine, and "clinker." Potentially economic deposits of kaolin, diamond, and building stone are under evaluation. All of the major deposits of commodities discussed here are located south of lat 56°30'N. Most of the locations are presented on Figure 1 POTASH Saskatchewan supplies approximately 30% of the world's demand for potash. Eight conventional underground mines and two solution mines produced an all-time high of more than 13 million metric tonnes of potash (KC1) (8 million tonnes K2O equivalent) in 1997, valued at over CDN$1.4 billion. All of the mines exploit the middle Devonian Prairie Evaporite. The four potash-bearing members of the Prairie Evaporite underlie much of southern Saskatchewan and extend southward into North Dakota and Montana and east- ward into Manitoba (Fig. 2). Halite and anhydrite separate the potassic members. The evaporite beds locally are interrupted by solution structures (anomalous ground). Some of the structures may be related to deep-seated tectonic features.

Jan 1, 1999

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By C. J. Pritchard, A. B. Cecala

An evaluation was performed on a district recirculation system at a trona mine in Granger, WY. A 1.52 m-diam (5 ft-diam), 37.3-kW (50-hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated about 31.4 m3/s (66,578 cfm) of air back into the intake. This amounted to a recirculation factor of about 20% of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 610 m (2000 ft) and 1829,m (6000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF6 tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1992

By Dinah O. Shumway

California's annual production of >11 million tons of cement, at a value of over $640 million, comes from eight companies, which operate 11 plants. Cement is California's second most important mineral commodity, representing 25% of its total annual mineral production. Although most of the cement produced is consumed within the state, current export locales include the Pacific Northwest, Nevada, Arizona, Utah, and New Mexico. An enumeration of the components required to produce cement is deceptively simple: calcium oxide (65%), silica (20%), alumina (4-5%), iron (3-4%), and calcium sulfate (4%) as a retardant admixture. The last, and most expensive, ingredient in cement manufacture is energy. Detrimental materials in cement mixes include excess .magnesium, alkalis, heavy metals, sulfur, and other volatiles. Each of the 11 cement plants in California requires a unique chemical solution of combined raw materials to produce a uniform product: portland cement. The geologist proposing solutions for the additive raw materials in cement manufacture must have a thorough knowledge of a particular cement plant's needs. In the California cement market, keeping the costs of additive raw materials down is one way to also stay competitive, and using a combination of natural and waste materials as additive raw materials allows cement producers to stay competitive.

Jan 1, 1999

By G. D. Hood, B. E. Davis

A problem that has continued to plague the Florida phosphate industry is loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µm) in a separate circuit have resulted in limited success, but recovery is still not optimum. A fundamental examination of the mechanisms involved in the conditioning of the coarse phosphate has led to results that seem to supersede common paradigms. The Bureau of Mines investigated conditioning parameters such as fatty acid/fuel oil dosage, residual clay content in the feed, conditioning time, mixing intensity, and conditioner solids content. The study revealed that the effect of all these parameters was important. However, it was discovered that contrary to common beliefs, the conditioning time affected the grade of the rougher concentrate much more than the recovery. Specifically, the longer the conditioning time, the less quartz that was floated. It was also discovered that high mixing intensity conditioners could lower the conditioning time required for good grade. Many phosphate operators use low intensity drum type conditioners. Optimizing the conditioning time, mixing intensity, and other conditioning parameters resulted in a rougher concentrate grading 30 pct P.2O5, with an attendant recovery of 95 pct.

Jan 1, 1993

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

By J. M. Dean, R. L. Grayson, N. P. Reddy, Y. J. Wang

This 1988 survey provided a cross section of computer software use by the US coal industry. From 1250 mailed questionnaires, 171 responses were received, representing a 4.9% sampling of the 3496 US coal mines. Since the distribution of responses by regional stratum matched well with the distribution of mines by stratum, the survey was given statistical validity. A statistical description details the computer use by region, mining type, organizational size, the level of application within the organization, the type of software application used, the variety of computers on which the software was used and the percent of users within engineering, management and general applications categories. Overall, 63.5% of the respondents use computers at some level in their organizations. All of the mines producing more than 454 kt/a (500,000 stpy) used computers. However, for those producing more than 9 kt/a (10,000 stpy) but less than 91 kt/a (100,000stpy), only 44% used computers. Generally, the software applications were still data-processing oriented. The application sophistication grew with increasing mine size. Computer system models and configurations for different sized organizations are recommended based on the configurations used in the industry at the time of the survey.

Jan 1, 1994

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016