Search Documents

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By Robert Burgess, Dale Gill, Jaco Steyn, Bill Kyslinger

"With mining, especially coal extraction, comes the necessity of supporting the roof. Since the 1950s, the primary method for roof support has been the use of roof bolts. Roof bolting is considered one of the most hazardous jobs in underground coal mining. In 2004, there were 3,405 injuries reported to the U.S. Mine Safety and Health Administration (MSHA). Of those injuries, 17 percent were associated with bolting machines (593 injuries). The majority of the injuries resulted from rock falling from supported roof. However, injuries involving a part of the body being struck by, or caught between, during bolting and drilling occurred with relatively high frequency (Burgess and Steiner, 2007).Roof drilling and bolt installation is labor-intensive and repetitive. These labor-intensive and repetitive requirements can lead to cumulative trauma. Operators are expected to perform a considerable amount of lifting, carrying, bending, reaching and stretching. Back and shoulders become sore from bending and twisting to install bolts or lift and position drill steels, wrenches and bolts. Confined operator spaces also contribute to difficult and awkward working positions for the operators (Cornelius and Turin, 1998).In South Africa, the majority of the roof bolting machines used are “man-in-position” style machines (Fig. 1). This puts the operator in close proximity to where the drilling and bolting process is performed. When proper operation procedures are followed, it has been proven to be a very effective, productive and safe system. The MSHA-certified automatic temporary roof support (ATRS), canopies and dust collection system of Fletcher bolters all provide the operator with unparalleled protection. However, there are some occupational hazards inherent to the zone located next to the drilling and bolting zone. This has led some customers to request relocating the operator away from this zone. The idea being that the operators will no longer be located in the face area, greatly reducing their exposure to dust, noise, machine and geological hazards."

Mar 1, 2017

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By B. Briggs

Over the past 15 years, the tunneling industry has pushed towards a higher degree of mechanization in nearly every phase of construction. The overall objective of the mechanization was to increase production and the level of safety in tunnel operations. However, the overall complexity of some systems have been a hindrance to a seamless transition to the newer technologies as increased maintenance requirements and re-training of skilled workers has altered the benefit curve for some innovations.

Jan 1, 2010

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By H. Zhao, R. Liao, W. Qin

Theoretically, controlling redox potential to a relatively low value and inhibiting jarosite formation on the chalcopyrite surface would be an effective strategy to accelerate the bioleaching of chalcopyrite. In this work, using limonite as seed crystals, the effects of the goethite precipitation process on the bioleaching of chalcopyrite were studied for the first time. The bioleaching results showed that the addition of limonite controlled the redox potential in an appropriate range and promoted chalcopyrite dissolution through the removal of ferric (Fe3+) ions. X-ray diffraction and scanning electron microscope analyses indicate that limonite significantly induced the goethite precipitation process and inhibited the production of jarosite. We conclude that promoting the goethite precipitation process with limonite is an effective strategy in accelerating the bioleaching process of chalcopyrite.

By R. Adsero

"A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts, the world’s mining equipment productivity has declined 20 percent during the past seven years (Lumley, 2014). Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear.The world’s mining industry fleet of more than 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually. This discussion will review a few of the tools available for improved productivity in dragline operations.Benchmarking equipment performance exposes the possibilitiesIn the September 2013 Mining Engineering cover story Graham Lumley and R. Adsero suggested that analyzing best practice equipment performance from an industrywide database for specific equipment performance improvement goals would be beneficial (Adsero, 2013). Benchmarking equipment performance by normalizing differences and then comparing specific measures of performance will provide a road map to improvement for those following the leaders. For those already performing at best practice levels, a benchmark confirms and bolsters what has already been achieved. As described in the SME February 2014 paper by this author, best practice is the average of the top 10 percent in annual output. Filling performance gaps identified by a comparison to best practice by investigating the details of the why and taking action to change, makes all the difference. This is true for all major mining equipment. Given the large gap between average performance and best practice performance most mining operations can benefit. Best practice performance provides a view of what is possible to the 90 percent majority of mining operations that are performing below the top 10 percent.For dragline mining operations, identifying specific characteristics and practices of leading dragline performance will provide a reference for comparison."

Nov 1, 2016

By E. M. Haynsworth

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began. As the flotation process was introduced in the late 1920's, the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The phosphatic clays with which we are dealing consist primarily of apatite, wavellite and montmorillonite. In the beneficiation process, we remove the -150 mesh material as waste. However, the particles are essentially smaller than -325 mesh, and more than 70% are smaller than three microns. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cubic feet for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5 cents per ton of, product (U. S. Bureau of Mines Circular 8404). This is a major cost of phosphate rock production.

Jan 1, 1970

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By M. Misra

The coral contaminated with plutonium at Johnston Atoll UA) was subjected to gravity and flotation separation processes at the Soil Washing Laboratory (SWL) and also at the Johnston Atoll UA) site. Tests were conducted with the contaminated coral fractions referred to as the "HP-l" ( hot particles) and the "sludge". The gravity process tested was centrifugal gravity separation and the flotation processes were conventional Denver mechanical flotation and tall column flotation. Flotation tests were conducted using both fresh and sea water. Industrial fatty acid (anionic collector) was chosen as collector to make plutonium-enriched particles hydrophobic. The use of flurosilicic acid and sodium silicate made the clean coral hydrophilic. The results show that each of the processed when tested with appropriate size fraction and operating conditions resulted in passing the success criteria. It was possible to obtain more than 80% weight of the original coral as "clean sand" having activity below the JA site "soil screening level" of 13.5 pCi/gm. The field tests spiked with plutonium particles showed remarkable success. The effect of depressants, flotation medium and the coral pretreatmentis described. Finally, a flowsheet developed by the University of Nevada, Reno to treat 8000 tons of HP-l pile presently stored at JA is presented.

Jan 1, 1996

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016