Search Documents

By J. C. Norman

The United States was the world's largest producer and consumer of boron compounds during 1994. According to US Bureau of Mines (USBM) estimates, boron mineral concentrate and chemical production in the United States totaled about 1.05 Mt (1.15 million st), yielding 560 kt (617,000 st) of B203, for a total estimated value of $370 million. This production level was about 2% less than 1993 revised figures. The United States continued to provide nearly all of its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid for export. Domestic employment in the mining and beneficiation of boron products during 1994 was 900 people, about the same as in 1993. USBM estimated total world production of boron of about 2.3 Mt (2.5 million st), yielding 1.1 Mt (1.2 million st) of B203. World production during 1994 was about the same as during 1993. USBM estimates US reserves to be about 210 Mt (231 million st) of ore and world reserves to be about 630 Mt (694 million st) of ore.

Jan 1, 1995

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By James E. Monsees, Richard J. Proctor

INTRODUCTION Los Angeles is one of the world's largest cities in area with a span of 70 km between its north and south limits. The population in the Los Angeles Basin exceeds 11 million people. Los Angeles is second only to New York City in density of U.S. urban population and it operates one of the largest city bus fleets in the world, 2,500 buses. After many years of planning and many consultants' reports, it is planned to initiate a 30 km (18.5 miles) starter line subway -- the "Wilshire Corridor" (Figure 1). Construction is to start in 1985. In several locations, subway routes ultimately will skirt or cross old oil fields, which may cause gassy tunneling. Of particular note are the La Brea Tar Pits, which overlie a part of the old Salt Lake oil field. Tunneling through tar sands for about 3 km will be unique for subway construction and will occur on the starter line. Experience with previous gassy tunnels in the greater Los Angeles area shows that tunnels can be completed safely if precautions are taken. Abundant ventilation is the main solution, although other precautions are discussed herein.

Jan 1, 1985

By John Stroiazzo, Bernard C. Aubé

Brenda Mines, located 22 km Northwest of Peachland in British Columbia, Canada was an open pit copper- molybdenum mine which closed in 1990 after 20 years of operation. The primary concern in Brenda's tailings and waste rock drainage is molybdenum at a concentration of approximately 3 mg/L. The mine drainage is alkaline and contains little or none of the typically problematic heavy metals. Given that the waters downstream are used for municipal water supply and some irrigation, a discharge limit of 0.25 ma molybdenum was imposed with specific water quality guidelines in the receiving creek. A review of all existing and potential molybdenum removal methods was undertaken prior to mine closure. The chosen process is a two-step iron co-precipitation with clarification and sand filration at a slightly acidic pH. A 4,000 usgpm (912 m3/h) treatment plant was constructed and commissioned in 1998, at a cost of $10.5M. The successful removal of molybdenum from the drainage water is explained with details on some design innovations and operational challenges encountered during plant start-up. Investigated sludge disposal options are discussed although the long term disposal scenario has not yet been finalised.

Jan 1, 2000

By Peter Zhang, Daniel Su, Bo Kim, Zoheir Khademian

Building on the research results and knowledge obtained from the ongoing National Institute for Occupational Safety and Health (NIOSH) Gas Well Stability Research, researchers from the NIOSH provided detailed analyses on potential longwall mining and gas well casing interactions at an unconventional shale gas well pad in a West Virginia longwall mine. Following the recommendations from recent research findings, the 5-1/2-inch production casings in all five wells were left uncemented from 4,200 feet below the surface to the surface. Prior to the first longwall panel excavation, NIOSH researchers conducted sophisticated three-dimensional numerical modeling to predict longwall-induced deformations and gas well casing stresses, which were compared with post-first panel and post-second panel mining 40-arm caliper surveys. The pre-mining predictions and comparisons with post-mining 40-arm caliper surveys were presented to all parties involved, including the coal and gas operators, Mine Safety and Health Administration (MSHA), Pennsylvania Department of Environmental Protection (PADEP), and West Virginia Department of Mines (WVDOM), prior to the re-entry operation on December 13, 2022. To date, the re-entry operation is a resounding success.

Jul 1, 2023

By Solomon S. Katz

As more and more computer software is written for geological mapping applications, the users of the software are discovering the problems of transferring data between the programs, maintaining correct data and integrating maps produced last week with those produced today. One way to deal with these situations is by using a geographic information system (GIs). Last September the USGS and National Academy of Science held a 5-day GIs symposium on integrating technology and geoscience applications (USGS, 1988). It was followed in October by GEOTECH '88 (Peters and Krajewski 1989) which had a session exclusively for GIs applications in the Geo-Sciences. Editorials in Geobyte (Leonard, 1986, 1988) suggested that geographic information systems will be the next major computer programs to be adopted by the mineral industries. As far- back is 1985, the Computer Oriented Geological Society (COGS) printed An Introduction to GIs in their newsletter (Katz, 1985). About 20 years ago, a revolutionary idea occurred in the world of business data processing. It was the idea that all related data be stored in a standard format, in a single place and that all related computer application programs would use the same data.

Jan 1, 1989

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By R. K. Amankwah, E. K. Asiam

Changes in the thermal-oxidation behavior and other properties of gold-bearing waste activated carbon when milled in both a ball mill and a vibratory mill were investigated. It was found that significant changes occurred in the oxidation temperature of the vibration-milled waste carbon as a result of increases in surface area and mechano-chemical activation. The mechano-chemical action brought about modifications in the crystal structure of the waste carbon. As a result, the vibration-milled sample was completely oxidized at a temperature of 450°C. Thus, the study established that vibration milling is a better way of lowering the temperature of oxidation of the waste carbon. Furthermore, the gold was found to be concentrated in the ash and, when leached with cyanide for 20 hrs, the gold recoveries from a sample having a head grade of 2 kg/t was 99.5% for the vibration-milled sample and 82% for the ball-milled sample. The lower gold recovery for the ball-milled sample was attributed to sintering of the ash, which was caused by the higher temperature required for its oxidation.

Jan 1, 1997

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation.

Jan 1, 1981

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024

By Gordon Hubbard, John D'Acierno

The Randgold Resources Ltd. mine operation in Syama Mali performs whole ore roasting followed by CIL gold recovery to produce gold. The roaster has operated continuously since the plant was first commissioned in 1994. The roaster design throughput is 216 tons per hour (5,184 TPD). Roasting provides for the oxidation of the· refractory components, organic carbon and sulfides. The energy balance for the system requires auxiliary fuel oil to be burned in the Circulating Fluid Bed (CFB) reactor. Energy from the 1200-1350 degree F roasted product stream is recovered and recycled back into the CFB using two fluidized bed coolers; one to directly heat the secondary air and the other to indirectly heat the primary fluidizing air. The basis of the design for the roaster was an extensive pilot plant test program, the results of which were scaled up to the full scale plant design. Due to variation in the feed at the mine a number of roaster modifications were necessary following the initial plant start up. During 1998 ore flotation capability was added to reduce the operating cost for the roaster and increase plant throughput.

Jan 1, 1999

By G. A. Plakhin, A. V. Luganov, V. A. Luganov, G. V. Gorbatenko

In order to extract gold from the complex sulphur-arsenic bear­ing raw materials and to remove arsenic and sulphur from the process in an ecologically safe form we have studied oxidizing roasting of highly arsenic gold bearing concentrates with soda, leaching of cinders, processing of the obtained solution and extraction of gold from the cake. There were processed concen­trates containing from 5 to 28% of arsenic, 12-20% of sulphur in the form of pyrite and arsenopyrite. The content of gold in the concentrates was 4-75 git. The roasting temperature was changed in the range of 773-l 173K, the consumption of calcined soda was 75-200% of stoichiometric necessarily for bonding of arsenic and sulphur into the water soluble compounds, the dura­tion of the process was varied in the range of 10-120 minutes. Under roasting in optimal conditions up to 97% of arsenic and 95% of sulphur go into water soluble compounds. The out­put of cake is 65-70% of the concentrates. The extraction of gold from the cake is higher than from the raw concentrates. The technology has been tested on a pilot plant scale

Jan 1, 1996

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By W. B. Beerbower

Resin bolting has enjoyed wide acceptance for coal mine roof support. Beginning in 1973, the first year of significant resin bolting in coal mines, we estimate that 2.5MM resin bolts were installed. This grew to 7MM resin bolts in 1974 and 13MM in 1975. Resin bolts are currently being used in over 300 coal mines throughout the major coal producing areas of the U.S. and barring major work stoppage we expect more than 17MM will be installed in 1976. Although not a cure-all, the number of unintentional roof falls occurring in many mines has been dramatically reduced as a result of converting to this "new" method of support. 1 The improved anchorage strength of resin bolts provides better roof support. (Slide #1) This anchorage strength provides a mechanism to resist changing roof stresses along the entire length of the fully grouted resin bolt, thereby assuring stabilization of rock strata over long periods of time. The ability to resist roof displacement is borne out by readings obtained from strain gauged bolts. These findings can be summarized as follows.2

Jan 1, 1977

By Steve Kral

The power industry throughout the world is in the midst of a significant transition that will result in a major restructuring. Deregulation of utilities in the United States is continuing, resulting in increased competition among power providers. The traditional ways that electric power is globally bought, sold and delivered will also change. However, according to the Department of Energy's (DOE) Pat Godley, one thing is clear: "Those who provide the power during the 21 st century will be those who are willing to change - those who are willing to accept new ways of doing business and willing to employ new technologies." Godley is assistant secretary of fossil energy with DOE. Her comments came during the opening remarks at the Fourth Annual Clean Coal Technology Conference, held in Denver, CO, Sept. 5-8, 1995. The conference was sponsored by DOE and the Center of Energy and Economic Development. Under the theme "Global Opportunity," more than 300 coal and utility executives spent three days discussing the new face of the electric-power industry throughout the world and the new, mostly clean coal technologies (CCT) that will be available to power providers.

Jan 1, 1995

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.