Search Documents

By Dennis C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required about 3 Mm2 (32.3 million sq ft) of fill over an area of about 600,000 m2 (6.5 million sq ft) in irregular terrain with relief of up to 40 m (130 ft). Earthwork construction was completed in about six months using mine waste, placed in 4 to 6 m (13 to 20 ft) lifts with mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10 m (33 ft). This was done to develop a mat for additional resistance to possible differential settlements due to the modest density of the fill and dynamic (earthquake) conditions. A single 2-mm (80-mil) high-density polyethylene (HDPE) liner was used below the leach pads. This was protected from the loading and unloading equipment by bedding and cover systems. It consisted of screened sand, gravel and silt as the bedding and cover layers and a heel of screened gravel and primary crushed low-grade ore.

Jan 1, 1995

By Don Macfarlane, Brian Heer, Tom Martin

The Manapouri Power Station, commisioned in 1969, is located in Fiordland National Park in the South Island of New Zealand. It is the country’s largest hydro power scheme and can generate 700MW of electricity. The power station utilizes the hydraulic head of Lake Manapouri, using an underground power station and a 10 km-long tailrace tunnel was constructed by drill-and-blast to allow discharge to Doubtful Sound. Power generation fell short of expectations due to higher than expected friction in the tailrace system. To remedy this a second tailrace tunnel was constructed between June 1998and May 2002. It consisted of a 10 m diameter, 10 km long tunnel in predominately gneissic rock and was excavated using an Atlas Copco Robbins TBM. High water inflows, Owner/Contractor production incentives and a major claim settlement were handled during the 5 1/4 year project. This paper discusses TBM advance rates, utilization factors that increased in the second half of the project plus an innovative method for sealing Tunnel 1 to construct the bifurcation.

Jan 1, 2003

By E. Topuz, M. J. McPherson, I. M. Konduri

The research is carried out to investigate the flow mechanics and effectiveness of face ventilation using induction fans, as an effort to provide a more efficient alternative to conventional auxiliary duct or brattice ventilation systems. The induction effects and plume longevity of fluid jets are being studied with the help of a plexi-glass model, using water as the fluid medium and creating a system that is dynamically similar to the flow in mine headings. This scaled model represents a typical 1.5m x 6m x 25m heading connecting to a crosscut. Reynolds Number criteria are used to obtain dynamic similarity of the flow in the designed model to simulate real mining conditions. The role of various parameters such as nozzle position in three dimensions, airway roughness, nozzle geometry, and flow rate in the jet are studied. During the laboratory tests, flow visualization techniques, coupled with still and video photography, were employed to identify the flow patterns. The results indicate that in typical coal mine headings, jet fans can produce effective face ventilation for distance up to 30 meters.

Jan 1, 1995

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials will borrow strongly from terrestrial experience but will also involve the necessity of handling literally unEarthly feedstocks, reagents and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed, with the production of rocket propellants, life-support fluids, structural metals and refractories as the goal.

Jan 1, 1994

By Kurt Burg, Allen Reicks

Tapered clamping devices have been used successfully over the years to transmit torque and bending loads from conveyor drives to conveyor belts. Proper design and application is important in the successful operation of these key components. This paper includes a historical review of component design and application and an overview of the important dynamics and limiting factors. Actual applications and simulation models are used to demonstrate the correct use of these devices.

Jan 1, 2002

By Landy A. Stinnett

Coal mines in the United States are the most productive in the world in terms of efficient labor employment. This is because of an abundance of workable coal beds, large infusions of capital, improved management practices and continuing competitive pressures. The standard unit of measurement for labor productivity is expressed as tons/manshift, although for underground mines, operators often refer to tons per machineshift. Articles written concerning labor productivity generally focus on measurement techniques, safety considerations, application of technology and training. This article will illustrate by example the impact of labor efficiency (or inefficiency) on the ultimate selling price of coal, f.o.b. mine site. During the past several years, the coal industry has seen significant improvement in labor use. Figure 1 shows the trends in productivity for all active mines in the United States from 1985 through 1994. Productivity in 1985 was 20.1 t/manshift (22.1 st/ manshift). This factor has increased almost linearly throughout that period to 37.5 t/manshift (41.2 st/manshift). This is a 7.2% annual compound growth rate.

Jan 1, 1995

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995

By Kenneth R. Maser

In the past 30 years, great advances have taken place in the development of tunnel boring machines, raise drills, large diameter drills and blind shaft borers that have revolutionized the shaft sinking and tunneling industries. Techniques for placing concrete linings, however, have not changed significantly during this period, and still constitute a stumbling block to the achievement of the rapid construction. In the past 5 years, Foster-Miller Associates, Inc. (FMA) has been involved with the development of a remotely operated shotcrete system for lining raise drilled shafts, an Extruded Tunnel Lining System (ETLS) for lining TBM bored tunnels, and a Continuous Shaft Lining System (CSL) for lining any type of machine bored shaft. This paper presents an overview of these three developments, including capabilities and limitations, a description of the concrete production, concrete placement, and advance rate, and control subsystems, a description of the concrete mix development required for each system, a discussion of test results to date, and an assessment of the state of development of each concept. Plans for future development will also be presented.

Jan 1, 1981

By D. D. Snyder, J. D. Bode, F. T. King

INTRODUCTION Only in recent years have the environmental hazards associated with mining and tunneling operations been fully acknowledged and determined remedial action undertaken. The nature of these excavation operations leads to a wide diversity of hazards spanning mechanical, electrical, chemical, environmental, and physiological. The most insidious of these are unquestionably the environmental ones which have the greatest long-term effect and are the most difficult to pinpoint and monitor. It is the atmospheric contaminants that lead to a significantly greater illness and mortality rate among miners. Dust is the most prevalent, hence most important of the atmospheric contaminants. Respirable particles lead to diseases characteristic of many mining operations: coal workers pneumoconiosis, asbestiosis, silicosis, talcosis, anthrocosis, etc. But toxic and suffocating gases can be equally insidious and the most innocuous pollutant, methane, leads to the most imminently disastrous results of all - explosion and fire. This means that truly effective monitoring of the environmental hazards in tunneling cannot be limited to a few simple standard check measurements. It must include the most precise measurements we can make for specific, documented hazards and even for factors, such as noise and heat stress, not immediately obvious as hazards. The Federal Metal and Nonmetallic Mine Safety Act and more recent Occupational Safety and Health Administration standards are clearly designed to match such effective monitoring. We must, therefore, consider not only presently available monitoring instruments and those currently under develop-

Jan 1, 1997

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By Carson Rife, Michael L. Clark

INTRODUCTION Zortman Mining Inc. is a wholly owned subsidiary of Pegasus Gold Corporation of Spokane, Washington. Pegasus has been producing gold and silver from the Zortman and Landusky mines since 1979. The Zortman and Landusky mines are two distinct open pit mines located approximately 6 kilometers apart in the Little Rockies Mining District of north central Montana. The two mines use large-tonnage, low- grade heap leaching techniques to efficiently process the gold and silver ore. PROJECT DESCRIPTION The Little Rockies rise abruptly 914 metres from the surrounding plains to about 1829 metres above sea level. The topography is quite steep, making efficient leach pad construction a major challenge. The climate is semi-arid with moderate summers and occasionally severe winters. Freezing temperatures usually arrive in late October or early November, influencing the effectiveness of leaching operations. GEOLOGY AND MINERALOGY The geology of the Little Rocky Mountains consists of steeply dipping sedimentary ridges forming an elliptical dome surrounding a core of intruding syenite porphyry. Within the syenite porphyry are well fractured and mineralized shear zones where the existing reserves and open pits are located. The ore is presently divided into oxidized, mixed, and sulfide. Only the oxides and mixed zones that are of ore grade are placed on the leach pads. The syenite porphyry host rock enables effective leaching of gold and silver to depths of 61 metres, having a major impact on leach pad construction costs. MINING All mining since 1979 has been by contractor. This enabled initial mining to commence without capital investment in equipment. Through competitive negotiations, Pegasus has been able to keep contract mining costs at levels very close to what would be experienced if Pegasus had purchased equipment initially. Contracts are negotiated yearly and are based on a unit price and haul distance for ore and waste. Haul distances have ranged from as little as 457 metres to as much as 3,050 metres. At present, Pegasus is developing a 27,000,000-tonne leach pad at the Landusky project that is adjacent to the minine area. This design feature will reduce the mining cost by 20 percent over the life of the mine. In 1987, over 5,900,000 tonnes of ore and 3,200,000 tonnes of waste will be mined at the Landusky project. Through 1986, 13,763,000 tonnes of ore have been mined at a waste-to-ore strip ratio of 0.60:l at the Zortman project, and 13,005,000 tonnes of ore at a waste-to-ore strip ratio of 0.79:l have been mined at the Landusky project. Current mining reserves are 32,769,000 tonnes of ore at a waste- to-ore strip ratio of 0.59:l. Through efficiencies of large-scale heap leaching, Pegasus has been able to lower the mining cutoff from 0.34 grams per tonne gold to 0.27 grams per tonne gold. This has reduced the mining cost per tonne of ore h percent through a reduction in strip ratio of 14 percent. Beginning in 1984, all pits were designed based on computer-generated "floating cone" pits. The geologic models were developed by Pegasus staff with a series of economic models evaluated. The resulting computer-generated pits were used as a guideline in designing the mine plans, including haul roads for final calculation of tons and grade. Input to the floating cone models consisted of mining cost, processing cost, cutoff grade (0.34 grams gold per tonne), recovery (67 percent) and gold price. Due to the gold being deposited primarily on the fractures of the syenite host rock, no crushing of ore is needed prior to leaching. This characteristic of the ore is a key in being able to profitably mine and process gold ore at an average grade of 0.69 grams of gold per tonne. Strict blasting control is also a key in success of the leaching operation. A system of splitting ore and waste in blast patterns has been devised to reduce dilution. Also, drill hole spacings are varied from 3m x 3m in breccia ore to 4m x 4m in syenite ore to 5m x 5m in waste. Drill holes

Jan 1, 1987

By Nestor M. Fillip

INTRODUCTION The Advisory Conference on Tunneling held in Washington, D.C. in 1970 under the auspices of the organization for Economic Cooperation and Development (OECD) forecast that $54 billion would be expended by member countries on underground construction in the 1970s. Construction activity since the Conference indicates the forecast may have been conservative. Statistics in the report indicated a vast increase in tunneling projects for mass transit, hydro-electric development, railroad tunnels, sewer and sewage retention reservoirs and water tunnels. Development of equipment is required to meet the demands for high speed excavation and provide tunnel driving systems with maximum efficiency and capability to sustain high speed advance rates. BORING MACHINE CAPABILITY During the last decade, use of Tunnel Boring Machines (TBMs) has increased. Where ground conditions and limits of machine design criteria permit, circular tunnel sections are either the only section , or an alternate sections specified in the documents: a TBM is either required or is an acceptable alternate means of tunneling. The evolution and acceptance of the TBM has had an impact on the construction and to a lesser degree on the mining industry. The traditional drill-blast-muck or "hand" mine

Jan 1, 1974

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By J. D. Miller

Certain bituminous coals of recent geological age are known to contain a significant quantity of natural (fossil or subfossil) resin. Such resinous coals are found in the western U.S., particularly the Wasatch Plateau coal field in Utah. Some of the seams in this field contain approximately 5% resin which has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction and precipitation. The purified resins are of commercial importance, being used in the adhesive, varnish, enamel and ink industries, etc: Recently, an improved flotation technique has been developed which involves ozone conditioning to selectively float resin from such coals. In this flotation process, a concentrate product which contains 95% resin at a recovery of 80% can be obtained in a single stage from coal containing approximately 10% resin, whereas conventional flotation at a similar level of recovery produces a concentrate having a resin content of 30-40%. Economic analysis shows that the ozone flotation process has good potential for use by industry.

Jan 1, 1988

By Paul D. Tomlingson

Maintenance costs in the mining industry often account for as much as 18-20% of total operating costs and with the cost of labor and materials rising, they threaten to become an even larger percentage of the total. Yet, without an effective maintenance program costs can soar beyond what they would be without a program. In other words, when production equipment is down, there is no production and no product to sell in the marketplace. This cost of downtime in lost product far exceeds the actual cost of maintenance, which is defined here as labor and materials. Thus, mine management must have an effective maintenance program to avoid downtime and meet production targets. Attaining an Effective Maintenance Program Many mine management and operations supervisors believe that an effective program is a function of how hard they push maintenance. Yet, when vital production equipment is inoperable and production is lagging, no amount of pushing helps. In actuality, maintenance has little control over its own destiny and needs support from other departments to deliver good service. Success of the maintenance program depends on gaining control of those factors that directly influence maintenance. Consider the following. Organization-The maintenance organization must be structured for maximum responsiveness to production needs. Unfortunately, some needs are immediate and many are unknown in advance. The maintenance department has little control over them. These outside influences limit the department manager's ability to control his own organizational structure. Preventive maintenance procedures-Routine lubrication, equipment inspection, minor adjustments and the like are controlled mostly by maintenance. Yet, scheduling preventive maintenance depends also on the availability of equipment controlled by other departments. Planning-The purpose of planning maintenance jobs is to ensure that the best use is made of maintenance resources. If the production department creates an environment of running repairs and emergencies, there can be little planning. Even well-planned jobs will suffer if there is less than full cooperation in carrying them out. As a consequence, the maintenance department is not blocked from planning, but the value of its planning is reduced. Scheduling-Maintenance scheduling should be a joint effort. Although maintenance does the planning, production must agree to the scheduled maintenance of its equipment. Workload-As a service organization, the maintenance department has limited control over its workload because it must consistently respond to other department's demands. At best, maintenance controls only the fixed portion of its workload-utility work, janitorial service, maintenance shop work, and assigned repetitive and preventive maintenance duties. Unscheduled and emergency work are initiated by operations. Major maintenance actions require full cooperation. Labor productivity-The effective use of labor is tied to other key functions of maintenance. These include organization, preventive maintenance, planning, scheduling, and emergency work. An area type organization, for example, can often respond more quickly to immediate needs than a centrally controlled maintenance group. Yet, area maintenance can result in lower labor productivity unless tight control is exercised. One of the advantages of a good "detection-oriented" preventive maintenance program is early discovery of problems and better opportunity to schedule corrective work in advance. Under planned work conditions, use of labor can be more productive. Complete planning and scheduling can minimize time spent on each job, increase effectiveness of supervision, and improve labor productivity. Finally, if emergency work is minimized, there are fewer delays, less lost time, better coordination, and more productive use of labor. While labor productivity is an important factor in carrying out maintenance, it also is influenced by outside factors. However, few realize the impact of being able to improve maintenance productivity. By improving the productivity of 30 men from 30% to 40%, maintenance could accomplish the same work value as if it had added 7.5 men working at 40% productivity. 30 (1800) (40%) = 21,600 man-hr/yr 30 (1800) (30%) = 16,200 man-hr/yr Difference = 5,400 man-hr/yr 1800 (40%) 7.5 men Leadership-The maintenance department can have significant control over its own leaders, the front-line foremen, but they must

Jan 12, 1982

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

By C. Menidiatis

The first cement plant of TITAN Cement Co was founded in Elefsis in 1902. It was the first cement industrial facility to operate in the Balkans and in the Eastern Mediterranean region. Currently have four cement plants in Greece producing 5.4 million tons per annum, and 25 ready-mixed concrete sites producing 1.4 million m3 annually. It has a total of 20 quarries, 14 of which are producing materials used in the making of cement while the remaining six produce aggregates used in the production of ready-mixed concrete. All plants in Greece are accredited for ISO 14001. The restoration of quarries began in 1976 at the company?s limestone quarry of the Patras plant, and was soon extended to all quarries. At that time, a department responsible for all environmental issues was established. To date, over 700.000 shrubs and trees have been planted and maintained at quarries, plants and ready-mixed concrete facilities, while over 100,000 trees have been donated to municipalities, communities, customers and to the Greek state.

Jan 1, 2002

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982