Search Documents

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By F. Aurelian

The development of the uranium mining industry in Romania started in 1950. The exploitation of Bihor region, one of the most important metallogenic zones of the country, began in 1962. Uranium exploitation activities were ceased in 1995 due to the exhaustion of the ore deposits. Between 2001 and 2002, due to the entire mining zone closure, ecological rehabilitation and decommissioning was initiated. The proposed solutions, concerning terrain, equipment and buildings utilization were elaborated according to the guidelines of the Romanian Environmental and Nuclear Authority.

Jan 1, 2006

By J. R. Heberger

"The Safety Pays in Mining web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of over 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items (services, equipment) on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining web application by discussing the development of the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app. INTRODUCTION Injuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker, or divert administrative resources in the wake of an injury. Safety Pays in Mining is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits. The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies don’t usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide — with half of the injuries in our dataset having mean costs higher than 90th percentile costs — just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of their potential impact on their company’s financial health."

Jan 1, 2018

By Yi Luo, FENGLIANG WU

Mine gob has long been a safety concern in the coal industry due to the air flowing through the gob area. Therefore, knowledge of the airflow distribution and locations of hazard zones in longwall gob is important to prevent and control these hazards. Due to the inaccessibility of mine gob, many numerical studies have been performed to simulate gob air leakage using computational fluid dynamics (CFD) programs, but most of the studies isolated the gob from the mine ventilation network (MVN) with only predefined pressure boundary conditions. The MVN is, in fact, not static in a dynamic longwall mining process, and it consequently changes the boundary conditions and the gob flow field (GFF). Therefore, the MVN should be incorporated in the CFD model to prescribe the transient boundaries. However, it is very challenging to couple the 1D MVN and the 2D/3D GFF to make the mine ventilation simulation realistic. This research uses a proposed novel finite tube method (FTM) to couple the MVN and GFF. In the FTM, the GFF is discretized into a finite number of flow tubes, each of which is formed by two adjacent streamlines. These tubes connect the MVN into a new coupling network. Based on the FTM, a model for gas migration in gob is established for delineating the hazard zones of explosive methane concentration and spontaneous combustion.

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By Yanan Zhang, Hongwei Deng, Feng Gao, Bo Ke

Recently, liquid carbon dioxide (L-CO2) blasting technology has attracted attention due to its good fracturing effect and safety performance, especially in coal seam permeability improvement. This paper analyzes the blasting effect of L-CO2 based on experiments and studies the fracturing mechanism from the perspective of stress wave action via theoretical analysis and peridynamic simulations. The results indicate that L-CO2 blasting achieves a good fracturing effect without forming a crush zone, and the loading rate and strength of the stress wave are key factors.

Jan 19, 2022

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By Göksel Hızlı, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

The carbothermic reduction of celestite is the first step in producing many strontium products. The way materials move in the rotary kiln has an essential effect on the carbothermic reduction efficiency as well as the temperature. In this study, the reduction of celestite ore and excess carbon blend in a laboratory-scale rotary kiln was investigated. In the experiments carried out at three different temperatures, the rotational speed and slope of the furnace tube were altered, and their effects on the reaction efficiency were examined. The leachability of the reduced powders and the content of the unburned coke indicated the optimal parameters for the reaction.When the speed was increased to 10 rpm, the powders weremoremobile in the stack and could react more easily with the furnace atmosphere. According to the results, celestite can be reduced by carbon at temperatures of 1000–1200 °C, at rates of between 5% and 75%. The maximumreaction yield (75%) was obtained with a slope of 2° and a rotational speed of 6 rpm at 1100 °C.

May 7, 2020

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

By Cuthbert Musingwini, Adeodatus S. Nhleko, Mahlomola I. Mabala

Optimization of a three-dimensional (3D) underground stope layout is complex given the number of variables and constraints to consider, such as the stope size. Determination of the appropriate stope size in stope layout optimization problems is a complex process that must consider several factors including placement of infrastructure and development, production scheduling, and equipment selection. An inappropriate stope layout can result in unrealistic expectations for a production schedule, consequently negatively affecting the derived economic value. Therefore, this paper used a dual interchange algorithm (DIA) to evaluate the effect of stope size on the stope layout economic value (SLEV) for a synthetic Platreef mineral deposit planned for extraction using sublevel open-stoping. The results showed that generally as the stope size increases, the SLEV decreases. This aligns with practical mining because larger stope sizes have a higher chance of incurring more dilution which reduces economic value, while smaller stope sizes enable more flexible extraction where unprofitable blocks can be left unmined as waste, thus increasing the derived SLEV.

Jun 25, 2023

By R. L. Miller

"Why should we care about diesel quality amidst the complexity of mining for minerals? Mining companies use a large amount of diesel fuel in their worldwide operations, both for moving ore from the mine to the processing mills or transportation hubs, and to generate power for onsite processing. This creates a large carbon footprint and poses both environmental risk with the production of emissions, and public perception of how those companies do their business as stewards of the environment while incurring a huge fuel expenditure. To improve diesel quality and create incremental value and greater environmental stewardship, the opportunity is broken down into several segments: 1. Mining industry diesel consumption 2. Fuel quality issues 3. Impacts on operations, economics, and emissions 4. Potential solutions 5. How improved fuel quality saves fuel expenditures 6. Economics of improved fuel quality 7. Recommended testing process 8. Fuel quality analysis checklist MINING INDUSTRY DIESEL CONSUMPTION The average grade of mined Australian ore bodies has halved, while the waste removed to access the minerals has more than doubled over the last 30 years, thus increasing energy consumption by 70%, (http://eex.gov.au/industry-sectors/mining/). Energy consumption and intensity in mining and mineral processing is rising at around 6% per annum. The mining industry is a huge consumer of diesel fuel worldwide, and the SRS Rocco Report of 4 August 2014 gives a better picture of recent trends. To better understand the reasons to reduce both fuel costs and consumption, we need to compare metrics on the amount of diesel consumed per each ounce of gold produced over the last decade. The rate of diesel consumption in gallons per each ounce of gold produced for the top five worldwide gold producers has doubled in the last 8 years from 12.7 gallons per ounce in 2005 to 25.8 in 2013 as shown in Figure 1 below.This is caused by 1) lower ore grades requiring more hauls to get same amount of finished gold product, and 2) haul trucks moving ore from deeper sources in open pit and underground mines. For one large multi-national gold mining company, the 2005 waste rock / production ratio was 52 metric tons/gold ounce; by 2013 that ratio had grown to 113 metric tons/gold ounce per the same SRSrocco 4 August 2014 report. Using the metrics above, the top 5 gold miners used over 591 million gallons of diesel fuel in 2013. The cost of diesel in dollars per ounce of gold has increased from $30.48 in 2005 to $101.14 in 2013, an annual appreciation of 16.2% as shown in Figure 2 below."

Jan 1, 2017

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010