Search Documents

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By E. Ben-Awuah, H. Askari-Nasab, N. Al Habib

Open pit mines are getting deeper with time and transportation expenses are increasing because of the increasing haulage distance. In-pit crushing and conveying (IPCC) is getting popular in deeper open pit mines as a suitable alternative to truck haulage because it offers a lower operating cost due to shorter haulage distance and less truck requirement. Semi-mobile in-pit crusher, currently the most popular IPCC system, is relocated every two to five years and the short-term plan needs to be updated accordingly. Short-term planning with IPCC is an area of research that has not been explored extensively yet and hardly any model can generate short-term extraction sequence considering an IPCC in place. This research work proposes a mixed integer programming model to generate short-term production plan within a time horizon of 12 months. The objective of the model is to optimally allocate shovels to minimize cost of material handling and maximize revenue subject to meeting plant requirement, maximum allowable tonnage variation and IPCC location constraints to achieve production and NPV targets set by strategic plan. The proposed model has been implemented in a hypothetical case study for verification. The comparison of results between scenarios with and without IPCC is expected to justify the use of IPCC in large open pit mines from a short to medium term perspective. A semi-mobile IPCC system with one relocation is considered in the case study.

Feb 1, 2023

By Andrew I. Hustrulid

The discrete element method has successfully been used to model the behavior of material flow in transfer stations. With position, velocity, and applied forces for every particle and boundary in the simulation available at increments of 10-5 seconds, the next critical step is the presentation of this data in a concise and beneficial form. This paper discusses several methods of presenting the data from discrete element simulations that are used to improve the performance of a transfer station. These measurements are also used as a learning tool to better understand and visualize how material transfers from one belt to the next.

Jan 1, 1998

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986

By G. A. Rosario, G. Peach

Twin 8.5 m diameter, 10 km long headrace tunnels under overburdens of up to 1870 m were excavated for the neelum jhelum hydroelectric project in north-eastern pakistan using two main beam gripper tunnel boring machines (tbms). Rock bursts were encountered and presented a significant danger to personnel and equipment. Micro seismic monitoring was installed to analyze rock burst characteristics and to create a database for future reference. Correlation of rock burst characteristics improved the ability to predict the likelihood, location, severity, and number of rock burst events. This paper presents the analysis of the micro seismic data

Dec 1, 2022

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By John E. Roberts

People are not a novelty. But the phenomenal numbers thereof, who have approached, settled, and been born in California in the past twenty-five years, are such a problem as to be a novelty in the broadest sense of the word. California, with less than 7,000,000 people in 1940, and over 19,000,000 in 1966. In 5 1/2 years, (1960-65) the southerly 14 counties of California, which together comprise one-half the land area of our state, had an increase in population greater than Colorado, or Arkansas, or Oregon, or any one of 19 other states.

Jan 1, 1967

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By Richard M. Crowell, Laurie M. Tahija, Keith D. Dagel

Echo Bay Mines Ltd. operates a gold heap leach in Round Mountain, Nevada, U.S.A. In the past two years, the mine has expanded operations from 13.5 kt/d (15 kst/d) to 41.0 kt/d (45 kst/d), making it the world's largest gold heap leach operation. The expansion is a separate system from the previous 12 year old plant, yet very similar. The flowsheet contains open circuit primary, secondary, and tertiary crushing with interstage screening. A leach pad stacker loads reusable asphalt leach pads. The process plant features carbon adsorption, pressure strip, electrowinning, and electrorefining.

Jan 1, 1990

By Maxine Wiber, Ross D. Gallinger, Brain A. Lewis

Poirier was an underground copper and zinc mine located in Northern Quebec that operated between 1965 and 1975. There are 5 million tonnes of acid-generating tailings, which have contributed acidity and metals to the Kananewesig and Kistabiche Creeks. The final closure plan incorporates the placement of all reactive material into the tails basin, installation of a geomembrane liner over the tailings deposit and a one metre soil layer to protect the liner. The environmental effect of the residual seepage was assessed from an ecological risk perspective. The Reclamation Plan has been accepted, and work commenced in 1998 to restore the site.

Jan 1, 2000

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Y. Topkaya, R. E. Johnson, B. R. Palmer, Jia-Jun Ke, Da-Ping Kang

The kinetics of the leaching of antimony oxide ore (Sb2O4) in aqueous hydrochloric acid solutions has been investigated. This dissolution reaction is a heterogeneous solid-liquid reaction. It has been found that the leaching temperature and the concentration of hydrochloric acid turn out to be the significant influencing factors on the leaching rate. The apparent activation energy for the leaching reaction was determined to be 63.5 W/mol within the experimental temperature region of 50O to 90O C. The experimental results indicate that the leaching process is controlled by the rate of the chemical reaction.

Jan 1, 1993

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987