Search Documents

By S. Tuylu, D. Adiguzel, A. Bascetin, E. G. Savas, O. Ozdemir

"Paste Technology has some advantages comparing to other surface disposal methods. With this method, it is possible to pump high concentrated solid materials to very long distances without segregation problem. However, it is known from Literature that pumpability of materials is completely related to rheological properties of the materials. For this reason, in this study, the rheological parameters (e.g. yield stress and viscosity values) of the paste material prepared from Pb-Zn tailings at various solid ratios (60-85%) were obtained in order to determine the pumpability of the paste material. Additionally, slump tests, which are usually used in mining industry, was carried out. Finally, regression analysis was made between the slump values and rheological parameters of the paste material to find a correlation between two independent parameters. The results showed that there is a great correlation between the slump values and the yield stress of the material. On the other hand, there was no correlation with viscosity: ty=430.28-16.877Sv (R2= 0,94; ty: Yield Stress (Pa), Sv: Slump Value (cm)). Based on the results obtained from this study, it can be clearly concluded that the slump values obtained from a simple test can be used to predict yield stress values of paste materials. INTRODUCTION Recently, surface disposal of mining tailings has become one of the biggest problems in mining industry in terms of environmental issues. Therefore, several researches have been focused on this subject in order to find a best solution or method for this problem. These studies showed that paste technology has some advantages compared to other conventional methods. Tailings thickened to the extent show no segregation of particles during transportation, and relatively small amount of settling occur post-deposition which are often called “paste” (Cincilla et al. 1997). Paste tailing technology has two applications in the industrial area as underground paste fill and surface paste disposal. Paste tailing technology was first started to be used in Grund mine, Germany in the late 1970s (Grice, 1998). Process tailing material, water and - if needed - cement materials, which are the components of the paste, must be blended to obtain a homogenous mixture suitable for pumpability. Consistency behavior of the paste material is determined using a conventional sedimentation cone concrete test (slump). Meanwhile, the slump value of the paste must be between 200 and 250 mm for surface applications (Newman et al., 2001). Additionally, in the case of underground paste system, the optimum slump value must be between 150 and 200 mm. On the other hand, the water content and density of paste at certain slump value change depending on the amount of fine particles in the tailing sample. While moisture of the material will be high, its density will be low because of surface area of particles which increases with decrease in particle size (Meggyes and Debreczeni, 2006). For pumpability of the paste to long distances, slump value of the paste must be good enough to be accepted for use of surface paste disposal. Paste material has a yield stress because they show non-Newtonian behavior and generally is classified as a Bingham plastic fluid. (Cooke, 2008; Theriault, 2003). In addition, the appropriate viscosity value of the paste along with the yield stress must be between 100 and 250 Pa (Bascetin et al., 2013; Bascetin et al., 2014; Bascetin et al., 2015)."

Jan 1, 2016

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Nine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1984

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By J. K. Conibear

Since the 1948 introduction of hydraulic fill at the Sudbury Ontario Mines of the International Nickel Company of Canada, 32,000,000 tons of water-borne sandfill and 420,000 tons of portland cement addition have been placed in underground workings. Fill method mining, currently conducted at six of the ten operating mines, accounts for 28 percent of the total mines underground production. Both classified mill tailings and screened alluvial pit sand are used as fill for cut-and-fill primary mining, undercut-and-fill pillar recovery, and backfilling of blasthole and shrinkage stopes. Cemented fill, consisting of a lean mixture of portland cement, is used in areas where a stabilized fill is required to reduce dilution and aid in the recovery of adjacent pillar ore.

Jan 1, 1970

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By J. Kretschmann, R. Amiri

"The Sangan iron-ore mines (SIOM) in Iran are located in a remote area, near the Afghanistan border. The deposit of SIOM is containing a geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61 %. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development (SD) is an influential ethical concept in mining all around the world. However, a successful realization of a SD is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes SD activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators could be filtered as the ones with the highest priority for the stakeholders. Moreover Islamic values and Iranian regulations and their influences on SIOM have been analyzed. Keywords: Iran, Sustainable Mining, SIOM, Evaluation, Islamic Values INTRODUCTION Mining Industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron etc., with 37 billion tons of proven reserves and more than 57 billion tons of potential reservoirs. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5.316 active mines and 84.922 employees in the whole country in 2012-13 (2) and according to the statistics published by Central Bank of Iran (CBI) in 2011 the share of this sector in the Gross Domestic Product (GDP) of the country was 1.2 per cent (3). Sangan Iron Ore Mines (SIOM) The deposit of SIOM is one of the largest iron-ore deposits in Iran, also considered to be one of the Middle East’s richest deposits, which contains a total geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61%. It is located 300 km southeast from Mashhad, the capital of Khorasan-e-Razavi Province, and 18 km northeast of Sangan town, in Khaf County, at latitude N34°24’, longitude E60°16’ in the north-eastern Khorasan-e-Razavi Province, 30 km west of the Afghanistan border (4) (Figure 1). SIOM is owned by the Iranian Mines and Mining Industries Development & Renovation Organization (IMIDRO). IMIDRO intends to develop an open pit mine complex and supporting facilities in SIOM for the production of about 20 Mtpy of iron oxide concentrate and pellets in four developing phases (5)."

Jan 1, 2016

By Seokwon Jeon, Ho-Young Jeong

"Various numerical methods have been tried to estimate the cutting forces of a TBM disc cutter. In this study, SPH/FEM coupled method was newly employed to improve the traditional FEM analysis. The disc cutter and rock were modeled by Lagrange and SPH codes, respectively. The numerical cutting test was carried out for representative Korean rocks with different cutting conditions. The results show that the cutting forces obtained from numerical simulation had a good agreement with those from LCM tests, and that applying SPH method to rock cutting model has advantages and improvement compared to traditional FEM method. Erosion criterion and erosion limit were not required to simulate the rock fragmentation process, and the cutting forces from the numerical simulation was more stable and accurate. The results indicate that the numerical simulation can be successfully used to estimate cutting performance of a TBM. 1. INTRODUCTION Various numerical studies have been carried out to accurately simulate the limitations of linear cutting machine (LCM) tests. Numerical modelling methods have advantages comparing with full scale tests in terms of cost and time involved. Many numerical methods have been used to simulate rock cutting process by different cutting tools and the studies are summarized in Table 1.In 2D simulations listed in Table 1, because they do not take account of rolling force and horizontal rolling mechanism of a disc cutter, indenter was selected as cutting tool in their modelling. For these reason, 2D modelling is not suitable for rock cutting modelling using a disc cutter. In contrast, 3D numerical models can take account of the indentation process by thrust force and penetration processes controlled by rolling force."

Jan 1, 2016

By M. E. Rossi, J. A. Bassan, J. B. Novillo

Sampling and geological models are the basis of recoverable resources models. They are pillars of mineral resources and reserves estimation, and what geostatistical methods for grade estimation should rely upon. The resource model is best estimated if geostatistical methods make good use of sound geologic models. Data collection from the original drill holes, including field procedures and the quality assurance and quality control (QA/QC) of those samples are pillar one of a resource model. The second pillar of the model is the good use of the logged geological information, resulting robust geological interpretations, and the corresponding three-dimensional models of those interpretations. These models are partly subjective and mostly conditioned by the quality of logging and the geologist’s experience. They are also conditioned by the quality of the three-dimensional models built, regardless of the modeling method employed, traditional or implicit. Grade estimation is more commonly done by applying some geostatistical method and using the two basic sources of information, data and geologic model. Multiple stages are involved in this process, and in all of them there are uncertainties and risks that have to be dealt with. Knowledge, understanding, interpretation, and management of the model’s fundamentals are critical, given that they directly affect its accuracy and predictive quality. The mitigation of related risks allows for the creation of opportunities, generating value and reducing the project’s uncertainty. This paper discusses some of the key variables, uncertainties, and risks involved in the resource modeling process, illustrating with specific examples; discusses possible risk mitigation alternatives, and proposes best practices to avoid or mitigate those uncertainties. Emphasis is placed on taking advantage of technological advances without ignoring fundamentals. INTRODUCTION In the area of mineral resource estimation, one alarming trend that these authors have observed in the past 20 years or so is that the care and diligence in checking the work as it progresses has generally diminished. This is, perhaps, an unintended consequence of the availability of new technologies and tools that attempt simplify and speed up the work involved. This has led to a more casual attitude towards checks and balances that have to be in place at any given stage of the process before proceeding to subsequent stages, as best practices dictate. To some extent, some of these aspects are covered in international standards for resource estimates reporting (JORC, 2012; CIM, 2010). But these are broad, and do not specifically recommend best practices to a level of detail that would have an impact on certain aspects of the process. There are numerous references in the geology and mining journals and conferences that discuss the consequences of poor recoverable resource models (Baker and Giacomo, 1998; Vaughan, 1997).

Jan 1, 2019

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.