Search Documents

By J. K. Mohanty, D. Panda, P. K. Sahoo, R. K. Paramguru, K. C. Nathsarma

Ferromanganese slag, a product of the manganese industry, was characterized mineralogically. The slag, which contains high Mn values, was characterized using optical microscopy, XRD analysis and electron microscopy. No separate Mn-bearing oxide mineral phase was found. The slag is amorphous, and no crystalline phase was identified in the hulk sample by XRD, However, in. fine fractions, quartz was identified. Scanning electron microscopy (SEM) revealed the presence of Mn, Si, Al and Ca in the matrix without the development of a mineral phase. Leaching experiments using H2SO4 were carried out to determine if Mn could be extracted from the slag. At room temperature, almost 100% of the manganese could be dissolved at a solid-liquid ratio o f 1:10 by leaching with dilute sulfuric acid. The impurities could be precipitated by pH adjustment to produce a manganese sulfate solution suitable for the production of MnO2 or electrolytic Mn metal. Based on the laboratory-scale experiments, a suitable process is proposed to recover manganese values from the, ferromanganese slag.

Jan 1, 1999

By Kyle Kittle, Kyle Knaeble, Albert Ruiz, Gregory Raines, Ryan Gewargis

The Chimney Hollow Reservoir Project (CHRP) is located southwest of Loveland, Colorado. CHRP is a component of the Windy Gap Firming Project, operated by the Municipal Subdistrict of the Northern Colorado Water Conservancy District. The inlet/outlet tunnel (IOT) for CHRP contains a reinforced concrete lined alve Chamber with PC membrane waterproong that was ecavated via seuential ecavation method to a diameter of feet. The IOT was ecavated using both drill and blast and road header with ground support consisting of steel sets, rock bolts, wire mesh and shotcrete. The IOT will withstand 300 feet of water head and rock ll surcharge load from the dam embankment constructed over the tunnel.

Jun 23, 2024

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By L. Xiao, P. Somasundaran

Three major types of solution chemical equilibria-involving minerals, solution, and flotation reagents such as collectors, frothers and modifiers-play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various floation reagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1992

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By P. Nelson, R. O’Connell, J. Rostami

Tunnel boring machine (TBM) system utilization is a critical factor for predicting machine performance. The process of estimating machine performance, including rate of penetration (ROP) and machine utilization (U) must incorporate an understanding of site geology, TBM specifications and site management. The study herein presents a preliminary analysis of the different activity time and downtime components from hard rock TBMs at two project sites to evaluate their impact on machine utilization. A comparison of crew experience, first between shifts and then between projects is included to analyze its effect on utilization and downtime. This work presents the sensitivity of the utilization factor to selected activities in the projects and the impact of geology and site set-up/logistics on machine performance.

Jun 13, 2021

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By Christophe Bragard, Marte Gutierrez, Haotian Zheng, Michael Mooney

This paper proposes a framework for applying surrogate-based approaches to evaluate SEM construction, which can both benefit the uncertainty analysis in the design stage and real-time calibration during the construction process. The performances of four surrogate modeling approaches, namely back-propagation neural network (BPNN), support vector regression (SVR), random forest (RF), and polynomial chaos expansions combined with Kriging (PCK), were evaluated and compared. A variance-based global sensitivity analysis (GSA) was performed on the surrogate predictor to quantify the impacts of geotechnical parameters on the deformation responses induced by SEM tunneling. The Regional Connector Crossover Cavern project constructed in Downtown Los Angeles was set as the benchmark problem to demonstrate the efficiency and reliability of the proposed procedure.

Jun 13, 2021

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

By M. J. Virnig

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-1 and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By F. Mensah-Dwumah, W. H. Baker, G. W. Clough

INTRODUCTION The practice of injecting chemical grouts into permeable soils in order to stabilize them for tunnel construction is a common procedure in Great Britain, Europe and Japan. In this technique, the grout penetrates the soil in a fluid condition, but hardens or "sets-up" in about one hour due to a chemical reaction. As a result, the soil, is strengthened and made less pervious, and this, in turn, reduces ground surface movements, limits ground water flow, and controls movements of the heading during tunnel construction. It is only within the last five years or so that this technology has been used in the United States. Most of the applications have been involved in the work for the Washington Metropolitan Area Transit Authority (WMATA) subway construction. The experience gained from this work is, in many instances, unique and should serve to guide use of the grouting technology in future projects. This paper documents five WMATA case histories; information is provided as to the soil conditions, method of treatment, reason for treatment, and tunnel performance. Locations of the five projects covered by this study are indicated in Figure 1. All are within the boundaries of the District of Columbia and involve soft ground tunnel construction. Basic information for the case histories is given in Table 1. Tunnel sizes and depths below the ground surface as well as general soil conditions are similar in all instances. The tunnels are about six meters in diameter and are located so that the crown is five to ten m below the ground surface. The soils typically consist of alternating sand, clay and silty sand strata. However, soil stratification details are

Jan 1, 1979