Search Documents

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By R. W. Plume

Gold extraction along the Carlin trend requires large withdrawals of ground water, which can be perched, unconfined at shallow depth, and (or) confined at depth. Five hydrogeologic units-Quaternary basin-fill sediments, Tertiary basin-fill sediments and sedimentary rocks, Tertiary volcanic rocks, Devonian to Ordovician siltstones, and Devonian to Ordovician carbonate rocks--form the framework for two aquifer systems that discharge along some reaches of the Humboldt River and its tributaries and are recharged by streamflow along other reaches. Ground-water withdrawals eventually could affect these stream-aquifer interactions. Further work is needed to quantify regional hydrologic processes and evaluate potential effects of mining on water resources.

Jan 1, 1992

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By P. Tanaskovic

This is presentation of a model which simplifies application of project management in control of the construction procedure of industrial units (mines, power stations etc). The model is made for further referrence of investors. The most demanding problem in large units is to find the best way of locating all activities within a network. The model uses term "line" (which refers to a construction unit) for a serie of activities which are to be sequentially executed (up to 1000 lines, each with 10-20 activities). The lines are coded in advance. Each line is described by a competent expert. Team of experts provide liason between lines on the basis of computer drawings. The method proved to be extremely effective. In order to provide smooth monitoring at all management levels, graphic documentation is given at 4 levels. The initial level is the third one, made based on input data (more than lo listings per one drawing). By condensation of activities along one line, another level is obtainable. Grouping of lines gives the first level (1-2 listing) for the highest management level. More detailed information is given for a limited (shorter) period at the forth level for the purposes of operational management. Each activity has three phases: prior to contracting, post contracting and accomplishment. All phases are presented at all levels, which enables investor to be continually well informed about construction advancement. Model is written in FORTRAN language. Programs comprise: maintenance of data base, calculation of time and costs and elaboration of graphic and other documentation.

Jan 1, 1986

By R. Bhaskar

The results of an experimental and theoretical research study into the spatial and temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-I) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection-diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.

Jan 1, 1988

By M. Karmis

"The process of coal mining, as indeed of the mining of any stratified mineral, is inevitably followed by some degree of sinking of the superjacent strata and consequently of the surface." Royal Commission on Mining Subsidence, Second and Final Report, London, 1927. INTRODUCTION The above statement was used to describe mining subsidence in the classic report of the "Royal Commission on Mining Subsidence," published in 1927. In fact, this phenomenon has been recognized in Britain since the early fifteenth century, as revealed from court records of disputes and litigations related to property damage above mine workings (Shadbolt, 1978). The first attempts to investigate and analyze the mechanisms associated with mining subsidence, however, date back to the 1800's and were pursued by Belgian Engineers. This research effort was initiated as a result of the widespread movements and subsequent structural damage suffered by the City of Liege in the 1820's. The most notable achievement of the Belgian school of that era was he publication of Gonot's treatise "Loie de la Normal" in 1871 (Gongt, 1871).

Jan 1, 1982

By R. Pinksen

The IOC Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1.0 m x 1.0 m x 1.0 m; 39 inches x 39 inches x 39 inches) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduces the infiltration of the emulsion into the cracks and fissures of the rockmass. Reduced amounts of oversize and more consistent fragmentation throughout the muckpiles has been a result. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a of first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A Digital Vision System (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By C. Bemelmans, L. Chia, T. O’Keefe

Lead alloys function effectively as oxygen-evolving anodes in copper SX-EW operations, and they are highly resistant to corrosion. However, the presence of an organic (from solvent extraction circuits) in the electrolyte seems to enhance solution line attack. Laboratory tests showed that lead is soluble in D2EHPA, Acorga and LIX 984 to a limited, yet measurable, degree. Lead alloys and various lead phases formed on the anode were tested to evaluate their effect on the corrosion process in organic media. Possible causes for anode corrosion and mechanisms responsible for their initiation are discussed.

Jan 1, 1998

By Daniel Hodouin, Claude Bazin, Sami Makni

A method is proposed to perform on-line data adjustment and inference of unmeasured variables, using measured flowrates and on-stream assays in mineral processing plants. The algorithm minimizes a weighted sum of squared residuals of the measured variables and squared species imbalances around the flowsheet nodes. The method is based on a trade-off between the material transient accumulation, evaluated by the imbalances, and the data inaccuracies, evaluated by the residuals (i.e. the adjustments brought to the measured values). A recursive algorithm is developed for on-line implementation of the method. It is a real-time extension of the hierarchical method for balancing steady-state data for bilinear mass conservation constraints. An illustration for a simulated flotation circuit is provided.

Jan 1, 1995

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Ivor Hawkes

INTRODUCTION High energy breaking is an alternative to using ex¬plosives in underground secondary breaking operations. It also is a means of upgrading conventional hand-held breakers, manual sledge-hammer breaking, and scaling bar operations. Major areas of application are in sec¬ondary breaking over grizzlies and at drawpoints. Other applications include breaking down ripping lips in longwall seam mining, scaling in stopes and rooms, general demolition work, and roadway maintenance. There is considerable interest in high-energy impact breakers for use in primary ore breaking, but, as of 1977, all such applications have been only experimental (duToit, 1973; Joughin, 1976; Wayment and Grantmyre, 1976). EQUIPMENT Essentially, a high-energy impact hammer is a boom¬mounted pneumatically or hydraulically actuated breaker. The machine basically consists of a piston that oscillates in a housing and impacts the end of a tool or moil thrust against the rock. The force applied to the rock primarily depends upon the impact energy of the piston-the higher the impact or blow energy, the greater the force and, thus, the greater the rock break¬age. Among drill and breaker designers, a common expression for blow energy is "force of blow." Hand-held breakers are limited to blow energies of about 140 J (100 ft-lb), because the operator is unable to handle heavier machines efficiently or to absorb the recoil energy resulting from higher blow energies. How¬ever, these restrictions do not apply to boom mounted breakers; machines with blow energies on the order of 4000 J (3000 ft-lb) and higher are available commer¬cially for underground use. There is considerable evi¬dence to show that increasing the blow energy also in¬creases the efficiency of the breaking operation; i.e., more rock is broken per unit of energy expended (Grantmyre and Hawkes, 1975). Thus, there is a trend to higher blow-energy machines, particularly where high¬strength rocks are to be broken. In relation to rock breaking, the blow rate of boom¬mounted impact breakers is not as important as it is for rock drills. This is because the breaker must be moved over the work surface between blows. The blow rate is governed eventually by the power supply, and typical blow rates range between 200 and 600 blows per minute. As a general rule, light blow-energy machines have higher blow rates than heavier machines. Table 1 lists most of the boom-mounted impact breakers that were available commercially during 1977, and it gives details of the blow energies and machine weights. Restrictions are placed on the blow energy by the machine weight and size, and by the strength of the boom. Typically, boom-mounted impact hammers have a blow-energy to mass ratio of about 1.5, with lower values for lighter machines and higher values for heavier machines. In addition to supporting the hammer weight, the boom also has to absorb the recoil energy of the blow, which can be on the order of 1400 J (1000 ft-lb) for large hammers operating in a horizontal mode. Interesting exceptions to the general run of impactors are the Joy HEFTI hydraulic hammers. In these machines, the piston impacts onto a fluid cushion that is positioned between the piston and the impact tool. This approach allows very high piston velocities, over 30 m/s (100 fps), to be used without the risk of break¬ing the piston or impact tool. Steel on steel impacts must be limited to impact velocities of about 10 m/s (35 fps) due to the high impact stresses generated; thus, increased blow energies can be achieved only by increas¬ing the piston size. The Joy 514 HEFTI®, listed in Table 1, has a blow energy of 27 100 J (20,000 ft-lb), but, as of 1977, the machine has been used underground only on an experimental basis. Using a fluid cushion between the piston and the impact tool allows the use of light pistons, reducing the overall machine weight. The recoil energy, which must be absorbed by the boom for a given blow energy, is directly proportional to the piston to machine mass ratio, and operating with light pistons provides an addi¬tional benefit in reducing the requisite boom size. Both pneumatic and hydraulic hammers are avail¬able commercially. Although hydraulic hammers are a relatively recent development, they already outnumber the pneumatic machines in use. There are many reasons

Jan 1, 1982

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By Andrea B. Baldwin

Solvay Minerals, Inc. (formerly Tenneco Minerals Company) is one of five producers who use trona to produce soda ash at Green River, Wyoming. Over the years, many producers, including Solvay Minerals, extended their product lines by manufacturing other sodium products based on trona. This paper focuses on the criteria used by Solvay Minerals in the selection of new products added at its Green River, WY operations. An example is given in the selection of caustic soda production.

Jan 1, 1993

By Farlow C. Davis

Magma Copper Company, San Manuel Division, is a wholly owned subsidiary of the Newmont Mining Corporation and located at San Manuel, Arizona. The ore body is a dessiminated porphry copper deposit in quartz monzonite. The primary copper mineral is chalcopyrite with minor amounts of chalcocite, bornite, and covellite. The molybdenite occurs mainly on fracture faces or else associated with quartz veinlets. Pyrite is the major sulphide mineral in gangue. The feed to the concentrator from the underground mine is approximately 0.720 percent copper and 0.029 percent molybdenite. The concentrator has a design capacity of 62,000 tons of ore daily. After a standard ore treatment circuit consisting of grinding, rougher flotation, regrinding, and cleaning, a bulk concentrate is produced which contains 27 to 29 percent copper and 1.0 to 1.2 percent molybdenite. This concentrate is pumped to the molybdenite plant feed thickener.

Jan 1, 1977

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By R. R. Klimpel

Over the last six years, several new commercial families of sulfide mineral collectors have been developed. This paper summarizes some plant data and use experiences gained with each of these product families. The first is a series of products (F-series) based on a chelation mechanism of attachment. The second of these families is a series of products (S-series) based on an electrochemically controlled mechanism of attachment. The major advantage of the F-series collectors is the very high metal recovery capability in complex ores involving Au, Pt, Zn, Ni, and mixed Cu minerals. The major advantages of the S-series collectors are the very high pyrite rejection capability along with reduced lime requirements in Cu/Mo plants.

Jan 1, 1995

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By R. O. Burt

The Tanco pegmatite is located in the Bird River greenstone belt of south-eastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). The orebody was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANCO), and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco's currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Corporation, and the Province of Manitoba.

Jan 1, 1988

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992