Search Documents

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By Linda D. Raedeke

The main platinum-group metal (PGM) deposit in the Stillwater Complex is associated with a stratiform zone formed by magma mixing. In general, the intrusion is a large, layered body of Archean age which formed by repeated magmatic injections in- to a single, large, hypabyssal magma chamber. The Complex is broadly divided into the lower Ultramafic series of olivine ± orthopyroxene rocks (1000-2000 m thick) and the upper Banded series of predominantly plagioclase-rich rocks (24500 m thick). The latter is further divided into Lower, Middle, and Up- per Banded zones. The Ultramafic series, plus most of the Lower and Upper Banded zones formed from repeated injections of an olivine-saturated magma, the rocks accumulating from the floor upward with a crystallization order of olivine, or- thopyroxene, plagioclase, clinopyroxene. The olivine-bearing subzones of the Middle Banded zone formed predominantly from a magma which crystallized in the sequence plagioclase, olivine, clinopyroxene. Olivine-bearing subzone I, with which the PGM mineralization is associated, occurs generally -400 m above the Ultramafic series-Banded series contact. Ore grade mineralization is usually found in plagioclase or plagioclase-olivine cumulates. The platinum-group elements are associated with disseminated base-metal sulfides dominated by the assemblage, pyrrhotite-chalcopyrite-pentlandite. Olivine-bearing subzone I marks an interruption in the crystallization sequence of the Lower Banded zone, with the reappearance of cumulus olivine and an associated change of the crystallization sequence. These changes indicate the addition and mixing of a secondary magma of the same composition as that which later dominated in the formation of the Middle Banded zone. Characteristics associated with mixing include laterally discontinuous but well-developed layers, xenoliths of ultramafic rocks, and sedimentary-type structures such as slum- ping and graded layering. The influx of new magma caused sulfide saturation by one or more of several chemical changes including addition of sulfur, decrease in oxygen fugacity, decrease in FeO, or increase in SiO2. Once an immiscible sulfide liquid was formed, platinum-group elements were scavenged from the magma by the sulfide liquid and segregated.

Jan 1, 2013

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Pentti Seppanen

The activities of Outokumpu Oy in the mining industry span all branches from prospecting to the production of refined metals and the manufacture of semifinished products. Products include copper, zinc, mercury, cadmium, nickel, cobalt, sulfur, gold, silver, iron ore, stainless steel, selenium, ferrochromium, lead and chromium concentrates, as well as chromite foundry sand. In addition, the activities of Outokumpu Oy extend to development and production of instruments, planning of industrial projects and instrumentation as well as the manufacture of specialized machines for ore concentration. The company now operates ten mines, eight of which are underground and all of which are in sulfide deposits except one. The fully automated monitoring and control of underground mine ventilation at the Pyhasalmi mine are an important technological contribution to the industry. Development work on the ventilation control was started in 1969, and since May 1973 it has operated in a fully automated computer-controlled mode. The Pyhasalmi mine has been in production since 1962, having begun as an open-pit operation. Development of underground mining began in 1967. The present annual production is one million tons all from underground mining. The underground mine is equipped with a main shaft and an auxiliary shaft, and two raises for ventilation. There is also a rampway from the surface to a depth of 500 m. The main shaft is for ore hoisting and the auxiliary shaft is used for waste-rock hoisting and for downcast ventilation. One of the raises is for downcast ventilation and the other is for upcast ventilation. The mining methods employed at Pyhasalmi are sublevel stoping with backfill, sublevel caving, and sublevel shrinkage stoping. Copper and zinc concentrates are produced. The Pyhasalmi mine is highly mechanized with about 4000 installed diesel horsepower underground. The maximum capacity of fresh air is 150 m3/s.

Jan 1, 1979

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By Cynthia M. Walck, S. K. Grant, R. D. Hagni

The Post Gold deposit is located in the northern part of the Carlin trend. The mineralization at Post occurs in proximity to a Jurassic-Cretaceous composite stock. Most of the gold at Post is hosted by non-metamorphosed calcareous siltstone and highly altered diorite, adjacent to the low grade skarn. Endoskarn, exoskarn, hornfels and marble are developed outward from the intrusive. The skarn is composed dominantly of diopside, tightly intergrown with gannet, k -feldspar, and sphene. The highest grade gold values are adjacent to the skarn, which acted as a permeability barrier to fluid migration. Post is the first Carlin-type deposit at which a skarn has been recognized to play a significant role in the localization of gold.

Jan 1, 1990

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991