Search Documents

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Ewald H. Kurt

The story of America's progressing standard of living is the story of machines. The automobile, the airplane and the telephone for example have made our transportation and communication systems what they are today. Even they depend in turn on another machine -- the rock drill. By making it possible to economically mine and quarry minerals in large quantities, this versatile machine supports virtually every American industry relying on the earth for its buried raw materials. And, like all machines, the rock drill's mechanical evolution was stimulated by production demands placed upon it. All percussion drills are mechanized versions of the original drilling unit -- man, Figure - illustrates a double jack team at work before the turn of the century. The man with the sledge hammer is the impact device while the man sitting is the rotation mechanism and feed motor. The first drifter drills (Figure 2) performed the same function but with increased mechanical efficiency. A piston controlled by a valve produced impact. A built-in ratcheting mechanism provided rotation and a hand-cranked screw provided feed thrust. As the industrial revolution proceeded into the twentieth century, the demand for raw materials stimulated refinements of all recovery machinery, including rock drills. As drills became heavier and more powerful, a mounting (or carrier) had to be provided to move the drill from hole to hole. This resulted in the development of the wagon drill (Figure 3). Propelled by muscle power, the wagon drill was for years the standard tool of the surface drilling industry (Figure 4). As drills penetrated faster and as labor increased in cost, the time consumed in nondrilling peripheral operations had to be

Jan 1, 1977

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By Michael Moats, Weston Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the USA. Electric arc furnace dusts processed to recover zinc produce a process residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine the predominant mineral phases and leached with common mineral acids. Atmospheric agitated leaching using sulfuric acid and hydrochloric acid were examined to determine the extractions of gallium, indium, and germanium as a function of concentration, temperature, and time. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 82%, ~100%, and 89%, respectively.

Aug 8, 2023

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By Xiang He, Xinzhong Wang, Ning Li, Bao Cao, Hongyang Bai, Zhigang Du

Revealing the periodic fracture pattern of the main roof and the key influencing factors of the support resistance is crucial for strata control and support selection of the shallow buried working face with large mining height. Based on the cantilever beam theory, an improved step rock beam model, and the measured strata pressure data of the 12,401 working face in Shangwan Mine, the mine pressure behavior law of the shallow buried with a large mining height working face was analyzed. The results show that both ratio of maximum principal stress to load (σ1/q) and ratio of maximum shear stress to load (τmax/q) inside the main roof increase with increasing periodic advancing distance, while the ratio of maximum shear stress to maximum principal stress (K) is the opposite, indicating that the increase rate of σ1/q is higher than that of τmax/q. K is less than 1 when the periodic advancing distance exceeds 8 m, indicating that the periodic fracture of the main roof will be dominated by tensile failure. Support resistance increases with increasing immediate roof thickness, main roof thickness, periodic fracture step distance of the main roof, and mining height, and decreases nonlinearly with increasing friction coefficient of periodic fracture rock block hinge surface. The main roof thickness, the periodic fracture distance of main roof, and the friction coefficient of the hinge surface of the periodic fracture rock block are the key factors influencing the support resistance. The advance breaking of the main roof and increasing the friction coefficient of the hinged surface of the main roof can reduce the support resistance of the working face. The support resistance of the 12,401 working face in Shangwan Mine presents an arch distribution characteristic. The average periodic weighting step interval, average support resistance, and dynamic load coefficient are 15.6 m, 17,552 kN, and 1.3, respectively. Finally, the rationality and validity of the model are verified by comparing the measured and theoretical values of the support resistance in the 12,401 working face of Shangwan Mine and other shallow coal seams with large mining height.

Apr 22, 2024

By W. O. Henderson, H. W. Seaney

The sinking and grouting methods employed at the 3C and 3D ore hoisting shafts and the No. 5 service shaft are discussed. The reasons for selecting a circular section over a rectangular one and other technical aspects are reviewed.

Jan 1, 1974

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By Nilufer Kursunoglu

Despite being crucial for meeting the world’s energy demands, coal mining operations present considerable health risks, especially when it comes to exposure to coal dust. Longwall coal mining, an advanced technique, has considerably enhanced production but made dust control more difficult. Due to its explosive nature, coal dust continues to be a serious and dangerous concern in the industry despite developments in safety technology. This study aims to comprehensively assess the risk of coal dust explosions by integrating fuzzy risk matrix and Pareto analysis methodologies, offering precise risk ratings for various root causes. A fuzzy risk matrix was developed to assign exact risk ratings to identified root causes. Additionally, a Pareto chart was used to identify the main reasons and suggest particular preventive measures. 17 significant causes were determined for underground coal mines based on the study’s methodology, and some preventive measures were suggested. In accordance with fuzzy risk rating values, root causes were divided into six categories. The root hazard with the highest risk rating was identified as ‘accumulation of inflammable gas/gases’. The proposed approach was used to examine incidents caused by coal dust explosions in Turkish coal mines in order to demonstrate the effectiveness of combining the fuzzy risk matrix and Pareto analysis for assessing coal dust explosions. This study gives not only a solid framework for risk assessment but also critical information for classifying the risks associated with coal mine dust explosions. The results highlight the critical necessity for proactive and preventive actions to reduce the hazards of coal dust explosions and protect the safety of mining workers.

Nov 16, 2023

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

By Aurel Goodwin

MSHA is the regulatory Agency which administers the Federal Mine Safety and Health Act. Although MSHA's principles largely derive from this Act, they do not exculsively derive from it. One might expect that our principles are contained in the regulations we have published to implement the Act. To a degree, this is true; but the regulations we have now were developed and published before the current Act became effective. For this reason, as well as others, there are some principles that we support which are not evident in our regulations, or in the Act. One of these is the ALARA principle. This principle requires that all unnecessary exposure be avoided; that is, all exposures should be kept "As Low As Reasonably Achievable." Almost all professionals in radiation control can agree with this broad principle; but it would be difficult to get agreement on a regulation which would translate the principle into industry practice. Rather, our regulations specify a limit to exposure for any individual. For radon daughters the current limit is four working level months per year. By having an explicit limit such as this, the ALARA principle often becomes lost and the limit becomes the goal. The principles contained in the Act are equally broad in scope. The principles apply not only for radiation protection, but also for toxic substances and harmful physical agents. The Act states that standards for such substances or agents shall most adequately assure on the basis of the best available evidence that no miner will suffer material impairment of health or functional capacity, even if such miner has regular exposure to the hazards dealt with for the period of his working life. The Act also provides that, although protection of health must be our foremost concern, other considerations shall be the latest scientific data in the field and the feasibility of the standards. Our regulations reflected similar principles when they were developed and promulgated. From experience with other health and safety laws, Congress realized that setting and meeting an exposure limit may not be sufficient to prevent disease. The Act, therefore, contains a detailed description of additional provisions to be included, where appropriate, in mandatory safety and health standards. One of these additional provisions requires that miners be informed about the nature of the hazards associated with their job and about the means for their own protection. Another provision requires the use of labels and other forms of warning to inform miners about the hazards, about proper precautions for safe use or exposure, about relevant symptoms of overexposure, and about emergency treatment. We have partially implemented these provisions through regulation. The Act requires also that standards shall prescribe protective equipment and control of technological procedures and that they shall provide for the monitoring of miners' exposures. We have implemented this provision to a degree also through regulation. Finally, the Act specifies that, where appropriate, a mandatory standard must prescribe the type and frequency of medical examinations in order to most effectively determine whether the health of miners is adversely affected by exposure. Additionally, when a determination is made that a miner may suffer material impairment of health or functional capacity by reason of exposure, that miner must be removed from such exposure and reassigned. In order to encourage miners to take the medical examination, the Act also provides that the miner shall not suffer loss of pay as a result of being reassigned. This additional provision on medical examinations has not been implemented by regulation for radiation hazards, nor for most other toxic substances or hazardous physical agents. We believe that this conference will provide us with valuable information on medical examinations for radiation exposure, as well as on other considerations to be used in future regulations. We still question whether our basic exposure standard of four working level months per year is adequate to protect a miner's health. This conference is indeed timely because both MSHA and NIOSH have been reviewing this issue for some time. I would like to reemphasize MSHA's commitment to education and training. MSHA strongly believes that miners should be informed fully about the real and potential hazards associated with their work. They should know the nature of the hazard and the means for protecting themselves from the hazard. The Act also emphasizes the need for training miners by requiring that new miners receive 40 hours of training before working underground and 24 hours of training before working on the surface. The Act also requires eight hours of refresher training annually. This training must include information on the relevant health hazards and the potential consequences of overexposure. Before I close, I would like to mention briefly another source of principles that MSHA often consults to obtain guidance for both the development and enforcement of regulations. These are the various court decisions that are handed down from time to time. Two in particular that I want to stress are the recent Supreme Court Decisions on benzene and cotton dust. Although neither of the decisions has a direct impact on mining or radiation, they do clarify some general principles and directions for regulatory agencies, such as the role of cost-benefit analysis and the need for risk assessment. In closing, I wish us all an open exchange of information for a productive and useful conference.

Jan 1, 1981

By David V. Fitterman, David L. Campbell

We've used direct current resistivity (DC), electromagnetic (EM), induced polarization (IP), and ground-penetrating radar (GPR) geoelectrical methods to study mine dumps. The results reflect lithology, pore water saturation, and dissolved solids in the pore water. If the pore water has a pH less than 5, conductivity maps can indicate acid generating potential. IP measurements can help distinguish mineralogy in mine dumps, especially concentrations of sulfide minerals. EM and DC can help locate acidic/high TDS groundwater associated with mine dumps. GPR methods failed at the sites we studied in the West. Our own conclusions are augmented by those from the recent literature.

Jan 1, 2000

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023