Search Documents

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998

By S. C. Torma

Sources of lead contaminated soils are numerous, i.e., the uses of leaded gasoline, lead-based paints, leaded pesticides, solders, smelting of lead concentrates, refining of lead products, automobile demolition, recycling of lead batteries, and so on. Conservative estimation by the US Environmental Protection Agency, EPA, indicated that several thousand lead contaminated sites are awaiting remediation. The current remediation technologies include immobilization, reclamation and soil washing. In this paper, the above remediation technologies will be reviewed, and where appropriate, the economics of processes discussed and future possibilities indicated.

Jan 1, 1996

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022

By Paul E. Epstein

Despite the controversies that have surrounded asbestos over the past 20 to 30 years, no knowledgeable authority has doubted the usefulness of this material. Were it not for the health risks associated with the manufacture and use of asbestos products, its physical and chemical characteristics would continue to be hailed as an undeniable boon to mankind. However, it has become clear over the past 30 years that like other major contributors to our modern industrialized society, asbestos must be handled responsibly and with the full understanding that lack of care can lead to injury, suffering and death. In this sense, asbestos shares characteristics with nuclear power, pesticides and even motor vehicle usage. It is unlikely that modern society would be willing to walk away from the benefits bestowed by any of these valuable resources. Rather, the appropriate response to the identification of danger is to define the type of risk, quantify its incidence, search for methods of decreasing the risk and implement programs to achieve the goal of minimization of risk. We should recognize at the outset that the risk cannot be diminished to zero without elimination of the material entirely from our midst. The concept of acceptable risk is a complex issue involving medical, legal, financial, moral and even psychological factors that defy precise quantification. In essence, the major danger produced by exposure to asbestos is its potential effects on the respiratory system. Despite the fact that asbestos workers have constant skin contact with the material and porbably swallow it in the course of their activities, inhalation of the fibers is recognized as the major health risk associated with its use. Aerosols of asbestos are inhaled not only by miners, millers and fabricators but also by urban dwellers who have no direct occupational contact with the material. This occurs because asbestos has been applied to our buildings and has been used in a wide variety of products that touch our daily lives. While it is estimated that three to four million people in the United States have been occupationally exposed to asbestos, the number who have been non-occupationally exposed is many times that number.

Jan 1, 1984

By Harry R. Dahlberg

Heap leaching is discussed as a unit process. Five factors are identified as the principal elements that can be measured and/or controlled. These are: 1. Material Size 2. Volume of solution 3. Tonnage of heap 4. Time 5. Solution concentretion. The Rate of Extraction Curves obtained from an actual heap or column tests describes the economic viability of the unit process. By analysis of these curves and the five factors end their inter-relationship it is possible to determine how the extraction rate can be increased. The practice of leach and rest used by many operators is analyzed and shown on a hypothetical rate of extraction curve. The influence of the driving force of the hydrogen ion and ferric Lon as Lixivants and its effect on the rate of extraction curve is discussed.

Jan 1, 1979

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By J. D. Miller

The processing of residues derived from various operations in the mining and metallurgical industry for by-product recovery is becoming more prevalent. A principal target for by-product recovery is flue dust produced by conventional smelting operations. Flue dust from zinc smelters has been processed for many years for the recovery of cadmium (1,2). The cadmium recovery technique which consists of a selective sulfation roast, followed by a water leach and zinc dust cementation, produces a lead cake residue (see chemical analysis in Table I), which consists primarily of lead sulfate.

Jan 1, 1975

By R. W. Salmi

The authors discuss the cooperative efforts by Minnesota Ore. Operations and Research; from the earlier development, testing and installation of fine shear screens in the Minntac Step III concentrator to the most recent testing and operating data that has resulted in the installation of Derrick Multifeed sandwich deck screens in Minntac Steps I and II. Pilot-plant test results that were obtained at the Coleraine, Minnesota Research Laboratory are also reported and demonstrate the effects of feed rate and feed percent solids on sandwich screen performance with two sizes of Minntac fine screen feed.

Jan 1, 1984

By Martin L. Smith, John M. Kemeny

In blasting, an optimal muckpile size distribution can be found in terms of mining and milling productivity and cost. Fragmentation control requires a means of modeling and evaluating blast results. A principle problem in the practical application of empirical blast fragmentation modeling is the evaluation of the muckpile's size distribution. Image analysis of video and photographic records of production size blasts at Cyprus's Miami and Thompson Creek mines is being used to provide data for estimating parameters relating fragmentation to blast design, energy factor and rock quality. The application of image analysis to the estimation of particle size distribution is reviewed with regards to the problem of fragmentation modeling.

Jan 1, 1993

By R. F. Korcak

There exists a wide array of industrial byproducts that produce beneficial responses in the soil/ plant environment. These materials range from clean-coal-technology residues produced during the generation of electric power (particularly those high in gypsum) to mineral fines produced by the aggregates industry (i.e., sand, gravel and crushed stone). A number of these materials are examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems are discussed.

Jan 1, 1997

By A. D. Hoagland

There are large areas on all of the continents with environments which are favorable for deposits of zinc and lead of Mississippi Valley type. In the developed countries, these environments have for the most part been quite thoroughly explored for the near surface deposits, and it will be necessary to direct more effort to the search for deeper buried deposits from which much of our future production must come. The difficulties of exploration for deep ore of this type are many and formidable, but the area of permissive environments beneath deep cover is many times as great as the area of the known near surface ore districts. It is a reasonable assumption, therefore, that numerous deposits wait for discovery and development. The finding cost, however, is certain to increase, and it is essential that concepts and techniques of exploration be improved if we are to sustain a reasonably strong productive capability into the 21st century. Exploration for deeply buried deposits requires at the outset relatively large areas of favorable geologic environment. The favorable horizons must be within economic limits of depth for the exploration as well as for the mining techniques which are currently available; and there must be some condition, design or strategy which will assure the explorer a reasonable chance of obtaining maximum benefit from discoveries which he may make.

Jan 1, 1973

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? THE CHALLENGE The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife", jumped on his bicycle and pedalled furiously down to the end of the driveway -- where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project.

Jan 1, 1979

By M. L. Sharrah

Communication about the energy problem has come at us in great profusion during the last couple of years--reports, speeches, editorials, advertisements--and events. Events such as the Arab embargo on oil exports which vividly demonstrated the world's dependence on oil, a finite and nonrenewable resource. And the three-fold increase in the price of oil which provides a constant reminder of the political and economic implications of dependence on foreign oil. A distinction among countries exists today which was almost inconsequential two years ago--the oil exporting nations and the oil consuming nations. The only rational way for the consuming countries to lessen the political and economic clout of the OPEC group is to reduce their dependence on oil. The United States is capable of playing a significant part in such a move for several reasons.

Jan 1, 1975

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

An investigation into the source mechanism of mining-induced seismic activity plays a vital role in understanding the various modes of failure observed in the underground deep-level South African mining environment. The seismic events data for this study was captured by the mine-wide seismic system operating at Kloof Gold Mine. This system comprises 40 4.5 Hz tri-axial geophones sampling at 6 kHz installed at locations that surround the stopes mining the Ventersdorp Contact Reef (VCR), Main Reef (MR) and Kloof Reef (KR). A set of 103,753 mining-related seismic events (-3.0≤ ML ≤2.7) that occurred during 2017 and 2018 was selected for this study. The mining depth of these seismic events ranges from 1600 – 4200 m; most located close to stopes mining the VCR ore body. The main criteria used to select a subset of events for detailed analysis were the number of stations that recorded the seismic event and the azimuthal distribution of the sensors.

Apr 26, 2022

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By Chris McKee

Quartz has been of interest in occupational health for years because it can cause silicosis after prolonged exposure. New OSHA regulations (Air Contaminant; Final Rule) list perlite as a nuisance dust. They conclude that perlite is nontoxic when air-borne total particulate concentrations are 15 mg/m3 or below and when quartz content is less than 1% crystalline silica. OSHA has established an 8-hour PEL of 15 mg/m TWA for total perlite dust containing less than 1% quartz. OSHA has established a 5 mg/m3 TWA PEL for respirable perlite. These limits will protect workers from significant risk of eye, skin, or other physical irritation. This regulation is based on a Group 2A classification as a probable carcinogen in humans, at the 0.1% crystalline silica level, by the International Agency for Research on Cancer (IARC 1987a, b). IARC found sufficient evidence for carcinogenicity of crystalline silica in animals and limited evidence in humans. Perlite is not listed as a carcinogen by OSHA or the National Toxicology Program.

Jan 1, 1990