Search Documents

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By Kefton H. Teague

An article entitled "The Rule of the Geologist in the Industrial Mineral Field" by G. R. Gullet, was published in the August, 1967, issue of the Canadian Mining Journal. Mr. Gullet defined industrial minerals as follows: "Industrial minerals are largely non-metallic minerals and rocks that find value because of their physical or chemical properties." This definition is brief, but all-inclusive. Mr. Gullet continues, "They include all useful minerals and mineral commodities except those used as fuels and those from which metals are extracted. Factors in the evaluation of an industrial mineral deposit are generally as different from those used in the evaluation of a metal deposit as is the assessment of a potential oil field. The key to the successful development of an industrial mineral, deposit is more often a balance of accessibility, transport, and proximity to markets than to any natural quality advantage of the deposit itself."

Jan 1, 1972

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By Charles R. Jenkins

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event, and drained the pond creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were run on samples of influent and effluent to evaluate pond performance. Particle size analyses were run on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement. Through the entire surface mining process un- protected soil is exposed to direct rainfall and subject to accelerated erosion. Without controls, receiving streams would be "choked" by the additional sediment load. Several states, including West Virginia, require that sediment control ponds be constructed to trap the sediment before the water enters receiving streams. Even well designed ponds have exhibited difficulty in meeting effluent limitations. In a study supported by EPA, about half the ponds did not meet effluent limitations (1). There is a critical need to reduce sediment losses using presediment pond controls or by improving sediment pond performance. The objectives of this study were to evaluate modifications designed to improve sediment pond performance by; 1) monitoring three ponds prior to modification, 2) install floating baffles and 3) modify the principle spillway and determine the change in pond performance.

Jan 1, 1985

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

By P. Soros

To accommodate the immediate and long term growth of the Hunter Valley, one of Australia's major coal producing regions, a third coal terminal was required in the Port of Newcastle, N.S.W. The initial capacity required was 15 million tons per annum, made up of 40 different blends, to be expanded to 50 million tons of 100 different blends, made up from 70 grades. Coal arrives in 3,200 ton unit trains, a total of 16,000 trains in a year.

Jan 1, 1986

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By K. Biswas, S. S. Peng

The stability of pillars in old mined-out districts is greatly dependent on the weathering action caused by moisture penetration into the pillar structure. Field observations in old mining districts indicated that this weathering action becomes critical in terms of the stability of the pillar if the coal seam contains parting or binder (layers of claystone or mudstone). The weathering action caused by moisture penetration over a long period of time degrades both parting and coal. However, it has been observed that the structural deterioration is more severe in parting. Moisture-penetration rates in parting and coal are different. The extent of the weathered zone in various layers of the pillar is primarily time dependent. This paper investigates, both in the laboratory and in the field, the effects of weathering action on coal and parting. In the laboratory, slake durability indices and uniaxial compressive strength tests for dry and saturated specimens are compared for coal. In the field, the in situ strength profiles for coal and parting layers are obtained, and the effect of time (in terms of the pillar age) on the strength profiles is studied An attempt was also made to establish formulae for time-dependent strengths of coal and parting.

Jan 1, 2000

By Mark E. Gershon

Conventional methods of drillhole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drillholes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drillholes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1983

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled- waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SB) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1984

By William G. Freeman

As with most industrial minerals, barite is freight sensitive. This paper is given so that others might gain from the experience of barite companies in reducing their transportation costs. Some of the approaches used were unusual and others standard, but by perseverance considerable savings were realized.

Jan 1, 1973

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By T. Lee

Ongoing economic success for mining companies is dramatically enhanced when they really know what they are harvesting, such that they can accurately forecast their head grades for any time period in excess of a month. This is an uncommon experience. It is a very common scenario for resource/reserve estimates to overstate the concentration (grade). Grade is a critical input of revenue, and hence, it is to cashflow projections. With the current direction being taken by the legal climate, it is no longer adequate for directors to accept the resource/reserve estimates of experts at face value. This is because resource/reserve estimates are the foundation of primary mineral economic decisions. Directors of mining assets need to undertake their own due diligence analysis of these estimates, in the best interest of themselves, and the company's shareholders. In the light of the industry's past achievements, this is quite a challenge. This paper suggests a set of new objective tools for directors to undertake an overview of the unique commodity concentration pattern and assess associated economic dynamics of each mineralization. These tools allow the examination of global graphical trends that can be helpful to directors and others in undertaking due diligence of resource/reserve statements. Ensure that it smells right.

Jan 1, 1995

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020