Search Documents

By W. J. Karwoski

A ground-support system for grizzly and haulage drifts was tested in Magma Copper Co.'s San Manuel mine. Eight two-piece, wide- flange steel sets were erected in a ventilation drift on the 2315 grizzly level. The sets were lagged with three different materials and back- packed with pea gravel and sand. The pillar on either side of the drift support system was instrumented with stressmeters and rock-bolt load cells, the backfill with pressure cells, and the steel sets with load cells. Results indicate a better survival rate than with typical monolithic concrete.

Jan 1, 1979

By Richard M. Tinlin

Some of the practices of the mining industry that may place an undesirable stress on the groundwater environment are coming under increasing scrutiny from legislators and regulatory agencies. Among these practices are mine dewatering, the use of tailings ponds, land rehabilitation, and technological innovations such as in situ leaching of waste clumps and ore deposits. Pernichele, noting that 24 states have enacted legislation controlling to varying degrees the environmental effects of mining, has emphasized the importance of assessing the potential for damage to groundwater when evaluating, planning, and designing mining projects. 1 Illinois has enacted legislation requiring anyone opening, operating or abandoning a mine site to obtain a permit from the Illinois EPA. The law is one of the first to require regular monitoring and reporting to a control agency. Legislation has also been recently enacted at the national level that will have a significant impact on the mining industry; e. g., the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). The stated objective of this Act is to restore and maintain the chemical, physical and biological integrity of the nation's waters. Specifically, according to Sec. 102(a), the Administrator of the U.S. Environmental Protection Agency (EPA) is required to prepare or develop comprehensive programs for preventing, reducing or eliminating the pollution of the navigable waters and groundwaters and improving the sanitary condition of surface and underground waters. The definition of the terms "pollution" and "pollutant" is of particular significance to those who must comply with PL 92-500. The definitions are quite broad and include most of the adverse water quality effects of man's activities. As defined in Sec. 502(19), "pollution means the man-made or man-induced alteration of the chemical, physical, biological and radiological integrity of water." Within the Act, the list of pollutants includes dredged spoil, solid waste, incineration residue, chemical wastes, radioaetive materials, heat, wrecked or discarded equipment, rock, sand, cellar dirt, and industrial waste discharged into water.

Jan 1, 1973

By Thomas V. Falkie

Of the various critics of federal energy and minerals policy we are hearing these days--and they are legion--few make their points more vividly than our fellow SME member and eloquent spokesman for the mineral industry. Mr. Eugene Guccione. In a moment of comparative mellowness. Mr. Guccione recently characterized Washington's time-honored legislative and bureaucratic machinery as a case of "...scientific illiterates asking the incompetents to do the unnecessary." I hope the prevailing industry view of government is not quite that harsh, and yet one cannot deny that government intervention is indeed pressing in on the mineral industry with increasing force. What is happening today in Washington and in state capitols will have enormous impact--both short and long term--on the future of coal and mineral production in the United States. Symptoms of this trend are everywhere. In the first place, there is a sentiment, widely held and still spreading, that the government must become involved-- that no matter what the problem, the solution lies in more government intervention. Free enterprise versus statist, reflex reaction organizations. When it cones to regulation in the resource field, there is too often a tendency to start out by assuming guilt on the part of the mineral industry. This can lead to laws governing mineral recovery that are more punitive than constructive...laws drawn up with little research into the scientific or economic considerations involved.

Jan 1, 1975

By T. V. Falkie

REMARKS OF DR. THOMAS V. FALKIE, DIRECTOR, BUREAU OF MINES, U.S. DEPARTMENT OF THE INTERIOR, BEFORE THE FALL MEETING OF THE SOCIETY OF MINING ENGINEERS, AIME, ACAPULCO, MEXICO, SEPTEMBER 23, 1974 This is a time of uncertainty on the world mineral scene. For some of the world's so-called "developed" countries, reserves and production of key minerals are running low. And, we have learned that the energy so essential in recovering and processing minerals can suddenly be in short supply. The prospects for a "no growth" situation in energy or mineral consumption are practically nil. Moreover, the world's economy is in flux, casting doubt on whether traditional mineral customers will continue to be able to buy, or for that matter, whether traditional suppliers of minerals will continue to sell. It is clear that the mineral situation is contributing to world inflationary pressures, which incidentally are most damaging to developing countries. So it is appropriate that SME members devote this session to the world mineral situation, and consider some of the opportunities and responsibilities that we will inevitably encounter as the future becomes the present. The opportunities, to me at least, are especially intriguing, I have the good fortune to be part of an organization that has an enormous capability and responsibility for dealing with mineral problems. The Interior Department's Bureaus, including the Bureau of Mines, have been around for a long time. They are. a prolific and reliable source of both mineral information and mineral technology.

Jan 1, 1974

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By A. D. S. Gillies

The effectiveness of coal mine face ventilation and the ability of air flow to maintain satisfactory methane and respirable dust levels in the working face area has been studied through the use of scale modeling techniques and underground testing procedures. In particular, consideration has been given to examination of the effects of operation of a high air flow machine mounted dust scrubber unit on face air patterns. Results obtained through a cooperative study with the Peabody Coal Company demonstrate that new mining cycles can be considered which increase production efficiency while maintaining satisfactory ventilation conditions.

Jan 1, 1982

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By John G. Hall

Everyone forms his own mental picture when the subject of copper is mentioned. To an architect, copper is a warm, enduring metal with a quiet beauty; to the historian, man's first metal; to the product engineer, the best electrical and thermal conductor of all commercial metals; to the investor, a volatile stock; to the speculator, the daily price quotation; to those in the mining industry, the challenge of producing copper for rising needs in the face of rising costs and lower grades of ore. At this meeting, we will look upon copper as a key raw material in industry, in national defense, in technology, in world trade, and as a principal commodity in the economies of several developing countries. As miners, and most of us here are miners, we are prone to view our role as suppliers of copper. We locate, mine, smelt and refine the metal. In the complexities of today's world, however, following a period of the longest domestic copper strike in history which caused critical world-wide shortages and widely fluctuating prices; it becomes necessary for all of us to concern ourselves with the whole spectrum of copper affairs -"from mine to consumer " But first we need to look at the miner's side of the picture -- capacity and production. We will examine these functions in terms of the whole world -- not simply the free world. Nature did not endow all regions of the earth equally, and copper in world trade has a way of ignoring political boundaries. Science and technology, as well, know no national boundaries. It is said that the "Engineering & Mining Journal" has as many readers in the Communist World as in the Free World. Nor is this a one-way street. We presently have available to us in the. U.S., cover-to-cover translations of many Communist World mining and metallurgical journals.

Jan 1, 1968

By Harold Bloom

Dimethylglyoxime reacts with nickel in a buffered ammonical-citrate solution containing the detergent ?Aquet? and hyroxylamine-hydrochloride. The resulting nickelous dimethylglyoxime is extracted with xylene. Visual comparison with standards permits the estimation of from 50 to 10,000 ppm of nickel. Soil, rock, or sediment may be decomposed by digestion with (1-3) nitric acid, allowing about 70 determinations per man-day to be carried out. With minor modifications to the above procedure, sediment and soil may be semi-quantitatively analyzed for nickel at the sample site. The chemical equipment is easily portable and the analysis extremely rapid because the buffer, dime thylglyoxime and xylene are added simultaneously to the sample and no heating is required. The sensitivity varies with the "availability" of the nickel ions; under favorable conditions, one may obtain a positive test for as little as 10 micrograms in soils and sediments. This procedure is similar to one, for the field determination of heavy metals described elsewhere by the author.

Jan 1, 1958

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By L. F. Moran

Rod Mill Grinding is an important and fundamental step of the concentrating process in Marcona Mining Company's plants at San Nicolas Bay, Peru. This Paper summarizes experience in regard to consumption and specifications of grinding rods based on twelve years operation of the grinding circuits. Marcona operates a Plant complex producing 10 million tons per year of beneficiated iron ore products including pellets, sinter feed concentrates, high grade concentrates as slurry and filter cake. Processing capacity is 15 million tons per crude ore per year of which 13 million are around in rod mills. A continuous testing program was carried out over the years. Initial studies of daily production operations gave indications of poor grinding rates in relation to mill size and power consumption, with a high rate of broken liners and rods. The broken nieces of rod were not automatically expelled and further interfered with grinding efficiency, while replacement of liners caused unwarranted do n tire. Objectives were to improve all phases of the Process by studying the effects of changes in rod diameter, length, alloy constituents, and volume and weight of rod charge.

Jan 1, 1975

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By J. C. Draper

The Duquesne Light Company and GAI Consultants, Inc. conducted a demonstration program aimed at establishing permanent vegetative cover directly on acidic, deep coal mine refuse. Several plots were treated with formulas varying in soil amendment application rates and plant species. Periodic monitoring of refuse chemistry has indicated when maintenance applications of seed and soil amendments were required. To establish drainage control, the site had to be regraded. The most successful formula was applied to the entire site. Specific treatment for acidic spots has been initiated. Results of the program indicate that adequate permanent vegetation has been established.

Jan 1, 1983

By C. William Parisi

Since the introduction of mechanical mining, some 35 years ago, a great deal of effort has been expended by the coal industry to solve the coal dust problem. The original concern was the possibility of a dust explosion or the propagation of a gas ignition; however, in recent years it has come to be recognized as a possible &apos;health hazard as well. In the middle thirties, the Pittsburgh Coal Company began an intensive study of the dust problem to determine the dust levels created by the various cycles of operation in mechanical mining and to make a comparison with those of hand loading operations. Numerous dust samples were collected with a midget impinger and it was found that dust counts varied from 38 to 268 million particles per cubic foot during hand loading and from 96 to 227 million particles per cubic foot during mechanical loading. The study indicated that the source of underground dust in coal mining could be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where most of the fines capable of becoming air-borne are produced. A secondary source is one in which most of the fines have been produced at some previous operation and are in such condition that they can become air-borne. Cutting, drilling and blasting are the operations which produce the primary dust. Secondary dust is formed by operations which include; loading, transportation and discharge at transfer points. The study showed clearly that the coal cutting operation was responsible for the greatest amount of dust and that the amount of dust produced varied directly with the speed of cutting; type and dullness of cutting bits; and the distance the cuttings had to fall to the floor. The information obtained from the study enabled our company to decide on a course of action and the direction to follow. With the cooperation of mining machine manufacturers, water tanks with a 200 gallon capacity were built into the machine trucks and were provided with a pump driven by a small motor. A length of 1/2" water hose carried the water from the pump to the two water spray nozzles located at the front of the machine. Water was delivered to the machine tanks by water cars which were filled on the surface or from an underground water supply. It was during these early days that wetting agents were introduced into the water system. Our studies revealed that wetting agents did little better than plain water in the abatement of the dust problem. It was found that when using a wetting agent less water was required to obtain the same results but we could not take advantage of this fact because it was almost impossible to keep the smaller nozzles open to reduce the amount of water being used.

Jan 1, 1967

By G. M. Li

It is shown that seriously preoxidized arsenopyrite can adsorb a large amount of copper ions as unoxidized one, but without, release of corresponding amount of Fe ions; seriously preoxidized pyrite cannot adsorb copper ions, but with release of a large amount of Fe ions. However, if the minerals are rapidly oxidized with potassium permanganate solution, both arsenopyrite and especially pyrite can adsorb a large amount of copper ions, but still without release of corresponding amount, of Fe ions. Cu adsorption (if there is any) on both oxidized arsenopyrite and pyrite is not based on the Cu-Fe exchange mechanism.

Jan 1, 1991