Search Documents

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

16.1.1-VENTILATION'S ROLE Importance of Ventilation and Environmental Control-Mine ventilation is necessary for the preservation of human life and for the conduct of operations involved in the underground extraction of minerals. It clearly is the most essential of the functions attendant to mining, yet it is auxiliary to the primary objective in mineral extraction. Ventilation in mining thus poses a paradox: ideally, it should be carried out with minimum interference with and cost to production operations, yet it is absolutely vital in providing adequate environmental con¬ditions to support mining. Deterioration of the atmosphere, along with rising ground pressure, imposes the ultimate constraint with depth in underground mining. Ventilation requirements and costs rise rapidly with depth. To preserve atmospheric quality under intense heat conditions, ventilation at great depths must be supplemented by air condition¬ing. Likewise, when mining at any depth under severe or excessive conditions of gas, dust or humidity, supplementary control measures must be employed. In recent years, environmental standards in mines have been raised substantially. While limits are based on human tolerance, increasing concern is being expressed for standards of human comfort. The reasons are economic, as well as humanitarian. Worker performance and longevity correlates closely with environmental quality. Further, adverse accident and insurance compensation rates are a consequence of unsatisfactory environmental conditions. No mining company can afford to be lax in its environmental and ventilation practices. Functions and Processes-Ventilation is the control of air movement, its amount and its direction. As a means of quantity control, it is one of the constituent processes of total air conditioning, the simultaneous control within prescribed limits of the quality, quantity and temperature-humidity of the air. Ventilation is the most common and most. important conditioning process employed in mines for air environmental control. In mine ventilation, air is coursed through the mine workings and openings themselves and, for auxiliary purposes, through vent tubing and ducts. Thus, many interdependencies exist between the mining system and ventilation method. In fact, the two often have evolved ,jointly, as in room-and-pillar extraction of bedded or tabular mineral deposits, such as coal. Ventilation in mines today is provided almost exclusively by large fans, although air flow may result due to natural (thermodynamic) conditions. As mines increase in depth, size and complexity, demands on the ventilation system to maintain more stringent standards of environmental quality likewise rise. On the other hand, never have the technology and resources of the mining industry to cope with environmental problems been so well developed as they are today. In spite of rising costs, it is unlikely that further progress in mine ventila¬tion and air conditioning must await technological breakthroughs. 16.1.2-NATURE OF THE MINE ATMOSPHERE Air Mixtures-Air is a gaseous mixture comprising the natural atmosphere at the surface of the earth. Thermodynamically, it may be thought of as a mech-

Jan 1, 1973

By F. Heivilin

Little did I know, in 1977, that when the A. P. Green Refractories Raw Material Manager showed me 5-6 burlap bags with samples of calcined high alumina bauxite in their testing lab that this was the start of China moving to be the number one user and producer of calcined refractory bauxite. According to Ted Dickson in his August 2008 Industrial Minerals article China produced about 4 million tons of calcined bauxite in 2007 using 2 million tons themselves. They imposed an export limitation of 970,000 tons in 2007 and 940,000 tons in 2008. A 10% growth will take up the difference between exports and production in 4 years. Two of these years are gone. It will take only 4 more years to eliminate the export quota in home use. Then they will be importing unless they increase production. Guyana was exporting over a half million tons in 1975 and sold less than 70,000 tons in 2002. Basai Metals Group bought Guyana?s deposits and is rose to 250,000 tons in 2007 and expects to produce 280,000 tons in 2008. PRICES According to the USGS Prices dropped from $172/per ton for Guyana calcines in 1980 just after the start of Chinese production to $122 in 1985. Guyana prices averaged around $120/ton from 1985 to 2005. China?s price dropped as low as $45/ton in 1995 undercutting Guyana and making it virtually impossible for anyone to get into the market. The price suddenly escalated to $550/ton FOB China in the summer of 2008 when China actually cut its exports in half. The price dropped in the fall as orders dropped. This is a four to five fold price increase. Is this a shortage of bauxite or a monopoly? Australia dropped out of the market in 2008 and Surinam, controlled by Alcoa, is not participating right now. Will these two come back in to make up the difference? Will the price hold up so they can make a profit? [ ] The low prices have undoubtedly affected the prices of the 60 and 79% alumina bauxite which can hold down the quantity of 80% plus calcined refractory needed in the world market. China is starting to upgrade lower quality bauxite up to 90% alumina. With high prices kaolin alteration to high alumina comes into play. The calcined bauxite is also used for proponents, Brown fused alumina, and abrasive grades which compete with Refractories. These and the tightness of supplies needed for metallurgical will hold prices up. TONNAGE China is the number one supplier and consumer of high alumina calcined bauxite in the world. Basai Metals Group Guyana (BMGG) is owned and controlled by Basai Minerals Group of China. This appears to be the second largest supplier. Australia has dropped production and Brazil is just starting to expand. It appears China is going to replace some of exports caused by the Export License 940,000 ton maximum in 2008 by raising Guyana?s (BMGG) production of calcined refractory grade bauxite. Companies exceeded restriction in 2007. Fines have been imposed for 2008. In August 2008 they appear on line to meet the 2008 quota. After August prices have dropped off as orders dropped due to the recession. Guyana was the largest producer in 1975 with 769,000 tons which decreased to less than 79,000 tons in 2002. The U. S. is a small part of the world production. I have used the United States charts to represent world imports because I have little data on what other countries import and pay FOB for their bauxite. China started exporting calcined 80% plus refractory bauxite to the United States in 1979 with 24,000 tons. By 1985 they were the number one importer with 169,000 tons. Guyana who had been number one in shipments to the United States gradually decreased to 36,000 tons in 2006. Guyana has been purchased by China BMGG and will increase there production to over 200,000 tons in 2009. Australia shut down production in 2008 and Surinam has elected to not send any Calcined bauxite to the United States. Imports to the United States from 1978 to present are as follows: [ ] Refractories are important because they affect 96% of the GNP. During the cold war we had stockpiles of 80% refractory grade bauxite

Jan 1, 2009

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By B. R. Utz

The goal of the DOE Coal Preparation Program is to provide industry with the scientific and engineering knowledge base to produce economically competitive and environmentally acceptable clean coal products for both existing and new markets. The DOE/PETC in-house program continues to conduct fundamental, exploratory, and applied research in the areas of physical, chemical, and microbial coal beneficiation to assist in meeting these goals and objectives. The Coal Preparation Division now has a new Coal Preparation Process Research Facility that allows continuous bench-scale testing of emerging coal cleaning technologies and ancillary coal preparation equipment at feed rates up to 1,250 kilograms (1.25 tons) per hour. Bench-scale and laboratory-scale research projects at PETC cover areas such as 1) the use of micronized-magnetite for fine-coal, 2) heavy-media cycloning, 3) fine coal reconstitution, 4) development and testing of coal preparation process flowsheet simulators, 5) dry coal beneficiation using electrostatic methods, 6) tracer methods to determine the efficiency of density-based separations, 7) selective oxidation of organic sulfur, and 8) microbial removal of pyrite and organic sulfur from coal. This paper will discuss several of these research areas.

Jan 1, 1993

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries' investment and production costs during the period studied.

Jan 1, 1989

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By Erie F. Wolstenholme

The purpose of this paper is to describe work undertaken, within the System Dynamics Research Group at Bradford Management Centre, into the development and application of a System Dynamics model of an international mineral industry; aimed at providing a basis for analysis of the interrelationship of supply, consumption and price over time, under different production and stocking policies. A review is presented of some of the major characteristics and problems associated with such industries. This is followed by an outline description of the model and the way it has been applied to examine various supply responses, in the light of changing consumption patterns. Demonstration results deal with model validation and with analysis of international buffer stocks and conflicting supply policies on the historic situation in the copper industry.

Jan 1, 1979

By Zhen-xing Diao, Feng Zhao, Ya-dong Xue

"Two important aspects of excavation performance of TBM are advance rate and cutter replacement/ring consumption, which is closed to the cost and construction duration of the project. To achieve this, a database of TBM parameters and the geological-geotechnical conditions during the excavation of Yinhanjiwei was compiled and analyzed. Relationships between different geological and TBM operational parameters were investigated. Results of analyzes show that there are qualitative correlation between Field Penetration Index (FPI) and rock geological parameters. And strong relationships between FPI and operational parameters are suggested. In this study, the cutter replacement and ring consumption were analyzed using statistical method for preliminary estimation in similar conditions. 1. ITRODUCTION Hard rock TBM is widely used in tunneling project nowadays because of its advantages to conventional drilling and blasting, especially in long tunnels. The biggest advantage is its high advance rate. However, rock conditions of tunnels are complicated. So TBM performance becomes a primary topic in tunneling engineering, which includes of rate of penetration, utilization, daily advancement, cutter consumption and so on. Many prediction models have been developed to estimate the TBM performance in the project planning phase. The most widely accepted and used models around the world are semi theoretical CSM model (Rostami and Ozdemir, 1993; Rostami, 1997) and the empirical NTNU model (Blindheim, 1979, Bruland, 1998).With increasing uses of TBMs in different ground conditions, an increasing number of researchers have developed new models in order to predict the performance of TBM more accurately in similar geological conditions.(Gong and Zhao, 2009; Hassanpour et al.,2009, 2010, 2011, 2014; Delisio et al., 2013; Delisio and Zhao, 2014)"

Jan 1, 2016

By Paul F. Richardson

Liquids containing suspended solids are encountered in most mineral processing applications. Solids levels cover a very wide range, from ppm levels in cooling water systems to slurries containing greater than 70% solids. When the aqueous phase is recycled or further processed, a solid/liquid separation process is used. Chemical additives used to carry out this process are called coagulants and flocculants. In other cases, one seeks to control or modify the properties of the suspension. Dispersants are chemicals used to aid in suspending solids in a liquid as well as to control the properties of the resulting suspension. Dispersants find a range of uses in mining and mineral processing such as scale control, filter aids, flotation aids, and slurry viscosity modification. Materials used as dispersants include inorganic salts, alkalies, organic surfactants, and polyelectrolytes. This paper discusses the use of dispersants in mineral processing, with an emphasis on control of slurry viscosity. The mechanism of dispersion and factors that affect the choice of dispersant will be discussed.

Jan 1, 1986

By James R. Hindman

Vermiculite is the mineralogical name generally applied to a group of hydrated, trioctahedral ferromagnesian aluminum platty or micaceous silicate minerals. In microscopic particles the mineral as mineral is differentiated from montmorillonite by a higher Si:AI ratio of approximately 3:l and a higher layer charge and higher cation exchange capacities. Commercial vermiculite, the vermiculite which is mined, beneficiated, and discussed in this chapter, is an important industrial mineral which is formed by the alteration of macroscopic particles of biotite and iron-bearing phlogopite. In natural form it has the size and shape of mica, while possessing the ion exchangeable properties of zeolites and some clays. Within the internal structure of vermiculite lie water molecules, which when rapidly heated to high temperature, transform into steam causing the vermiculite particles to increase in volume. This process of thermal exfoliation produces a lightweight product which finds use in various construction products, agriculture, horticulture, and other industrial applications. In exfoliated form it has the low density and biological inertness of expanded perlite, while maintaining a chemically active surface. Most of the uses of vermiculite are for the thermally exfoliated material. In addition, the cation exchange potential of vermiculite and its layer-silicate structure are properties which can be used as the basis for numerous products including intumescent coatings and gaskets, inorganic films, and the treatment of nuclear and other toxic waste. When chemically and physically modified, it possesses some properties common to organoclays and synthetic compounds. In high purity concentrates and manufactured products, these properties can be altered and optimized in applications to produce superior performance. GEOLOGY Mineralogy Vermiculite was first described as a mineral by Thomas H. Webb in 1824. Webb believed vermiculite to be a variety of talc and described its diagnostic property of thermal exfoliation thusly: "If subjected to the flame of a blowpipe, or that of a common lamp, it expands and shoots out into a variety of fanciful forms, resembling most generally small worms having the vermicular motion exact." Observing that with one exception, all commercial vermiculite has formed by the alteration of iron-bearing phlogopite, a simple definition of vermiculite might be the alteration product of trioctahedral micas, macroscopic particles of which display marked exfoliation when heated rapidly to temperatures above 374°C (the critical temperature of water). The first vermiculite described was found near Worcester, MA, but it was later pointed out by Brush (1866) that vermiculite had been known for some time in Japan as a children's novelty. Because the techniques for mineral analysis were somewhat primitive com- pared to those routinely available today, and because the structure and crystal chemistry of the micas and related minerals were not widely understood, the early literature generated at least 20 "new" minerals which were nothing more than variations in the color and chemistry displayed by vermiculite. Trade names such as Dugarlite, Mandolitem, Strong-LiteTM, and Zonolitem are sometimes used to denote commercial vermiculite, thermally exfoliated vermiculite and their products. Vermiculite particles resemble mica and vary in color from colorless through tan and green to black, depending on the chemical composition. Most physical and optical properties are close to those of biotite, with perfect basal cleavage, hardness between 1.5 and 2.5 Mohs, and specific gravity between 2.2 to 2.8. Fine-sized particles will feel talcose, especially when wet. However, for commercial vermiculite the diagnostic test is that of thermal exfoliation. Vermiculite can display a wide range of compositions, depending on the composition of the original mica and the change of chemistry during weathering and ion exchange. Chemical data for some commercial vermiculites are given in [Table 1]. There are numerous analyses for vermiculite given in the literature, and the analyses of vermiculites from commercial deposits will fall within the range indicated by the average analysis in the table. Many analyses separate the adsorbed water (H2OP) from crystalline water and water as hydroxyl (H20+). The basis of separation of adsorbed water is generally considered to be 100°C. However, hydrate water within the vermiculite interlayer begins to be lost at 75°C and lower. Therefore, measured water content and loss on ignition are combined in the table as H20[total].

Jan 1, 1994

By Serge Payant, Michael G. Li, Lionel J. J. Catalan

Alkaline solution rinsing for decommissioning of an acid-leached residue was evaluated by column experiments, neutralization tests and solid characterization by XRD and SEM. It was found that consumption of a strong alkali during residue neutralization was much greater than that required to neutralize the soluble acidity. The excess alkalinity was consumed by solid-phase conversions unnecessary for the success of decommissioning. Alkaline rinsing did not reduce the time requirement for decommissioning when compared with plain water rinsing. Since no benefit is gained to compensate for the additional costs associated with excess alkali consumption, we conclude that strong alkaline solution rinsing is in fact inferior to simple water rinsing.

Jan 1, 1998

By E. Woodburn, Harrison R. Cooper, R. Putman

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application know- ledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016