Search Documents

By Thomas P. Meloy

Theoretical development of comminution models has come about in the last 10 years. These models assume that the material being broken is homogeneous and that the compression or energy wave is uniform throughout the specimen. Obviously, this is not the case because most comminuted materials are rocks with either many phases and/or definite grain size. The mathematical models deriving the size distribution of daughter fragments resulting from the comminution of brittle, single particles are of two schools. The first model, proposed by Gilvarry in 1961, was based on the concept of volume, surface, and edge flaw activation. The second, proposed by Meloy in 1960, was based on the concept that the crack density is a function of the energy in the comminution wave. The flaw theory has run into increasing theoretical problems and is now being abandoned. On the other hand, the crack density theory has been expanded and has successfully considered the case where there are inhomogeneities in the comminutive wave. However, the main constraint of a homogeneity in the solid being comminuted has hitherto never been overcome. In this paper, a very general derivation of the crack density model is made for inhomogeneous solids by replacing the assumption of homogeneity with an arbitrary function, P(y), which describes the susceptibility of the material to comminution as a function of position. The restraints on this function, P(y), are very broad and, hence, the derivation is extremely general. General use of the equation derived necessitates a detailed a priori knowledge of both the fracture process and of the physical properties of the material being fractured; this knowledge is expressed in open form as, P(y), the linear probability density that a plane of fracture intersects at point y on an arbitrarily oriented line segment of total length xo through the original particle. From these assumptions, a general expression for the cumulative mass distribution of particles resulting from fracture is then postulated. It is: [ ] where, B(x), is a cumulative mass of material finer than size x, r is the average number of crack,, (y), is defined above and xo is the initial particle size. It is shown that suitable assumptions reduce the expression to the theoretical results of Gaudin and Meloy and to special forms of the empirical equations of Rosin-Rammler, Gaudin and Schuhmann. Semi quantitative agreement is demonstrated by Grimshaw with experimental results of a very complex fracture of heterogeneous sandstone blocks. A need is expressed for more theoretical development of P(y), and a more extensive experimental study of both homogeneous and heterogeneous fracture. The full mathematical derivation is presented for the first time in this paper. The general implications of the equation and its application are also discussed.

Jan 1, 1968

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By Ronald J. Roman

As in every business venture, the primary objective of a mining operation is to make money for those who supply the venture capital. Therefore, all decisions concerning the operation of the mining operation should be made in light of the resulting effect on profit. The ultimate control is on profit, but the process is controlled, for example, by aiming for a recovery or concentrate grade knowing its effect on profit. The normal procedure used to determi.ne the profitability of a venture is to "present worth" all costs and incomes back to some arbitrary year zero. Every company has formed a management decision as to what it will require as a minimum return before it will undertake an investment. Once the economic analysis is completed, investment will be made only if the venture shows a positive present worth. If two alternatives are available, the alternative with the larger positive present worth is the one chosen. The same principles can be applied to the selection of a production schedule.

Jan 1, 1971

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By M. J. Zdunczyk

The final 1995 figures on industrial sand and gravel have not yet been compiled by the US Geological Survey (USGS). There is usually about a nine-month lag time in receiving and compiling this information. However, USGS estimates that domestic production of industrial sand and gravel will increase about 4% to 28.2 Mt(31 million st). The average unit price is expected to increase as well. The top five producers during 1995 were Unimin, US Silica, Fairmount Minerals, Oglebay Norton and Morie Co. Glass manufacturing for containers, automobiles and buildings was mixed during 1995. Containers, the largest consumer of silica sand, remained steady, with regional increases. However, silica use in glass containers face increased competition from plastic and recycled glass (cullet). It was reported that the Pepsi Cola announced plans to replace glass containers with plastic during 1996.

Jan 1, 1996

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By Myles E. Robinson

Significant changes in the markets for coal have taken place since World War II, As used in this study the term ?coal? will refer to bituminous coal, The anthracite industry in size, characteristics, and problems differs materially from the bituminous coal industry, These changes have both influenced and been influenced by the mechanization of mines, and by decreased distribution costs, especially in transportation. It is the purpose of this paper to examine these post-war changes, to assess their impact upon the production and distribution of coal, and to explore future market developments in the light of past and present trends and relationships. The layman lacks adequate informatian on the production, demand, and distribution of coal. There are two reasons for this. First, there is a relative lack of statistics coveting the industry, Coal operators and distributors are not required to file with any government agency the type of much more complete statistics filed by the railroads and public utilities with national and State agencies. The Bureau of Mines assembles much useful information on the coal industry, but several areas, including that of investment and finance, have no central depository which can be used to keep the public informed of the nature and extent of the industry and its problems.

Jan 1, 1964

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By R. A. Seitz

Although the role of the collector has long been thought to play a predominant role in coal flotation, recent investigations by the authors show that the frother plays an equally important role. These investigations have included extensive testwork in several coal preparation plants and in the laboratory. The factors which were investigated include the absolute level of collector and frother addition, the ratio of frother to collector additions, the type of frother, and the particle size distribution of the feed. Results from this testwork reveal strong interactions between these factors as well as the necessity of considering these factors in order to optimize the reagent regime.

Jan 1, 1987

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By A. B. Van Cleave

It was first pointed out in 1934 by Gaudin (1) that the "oily" oxidation product of the alkyl xanthate ion-dialkyl dixanthogen, might be the "active flotation agent" on sulphide minerals and there have been a number of studies supporting this hypothesis (2,3,4). However, all of these studies have relied largely on electrochemical evidence. Galena, being a semiconductor, may be used as an electrode in aqueous solution and it was shown that ethyl xanthate ion does not adsorb with charge transfer in the absence of oxygen unless the potential of the galena surface is above -100 mv versus the hydrogen electrode (H2 E). At this potential the galena surface is slightly hydrophobic but does not become strongly hydrophobic unless the potential is raised to 210 mv (versus H2 E). It is suggested that, at potentials of 210 mv or above, ethyl xanthate ions are oxidised to diethyl dixanthogen and that chemisorption of oxygen raises the galena surface to this potential. On the other hand, examination of xanthated galena surfaces by chemical or physical methods (5,6,7) has failed to detect dixanthogen and it has been shown that dixanthogen may be reduced to lead xanthate at a lead sulphide surface. (5,8)*. It was suggested by Leja and Poling (5) that, as dixanthogen is a neutral molecule it would not be repelled by the negatively charged galena surface so that the adsorption was envisaged as taking place through homogeneous oxidation of the xanthate ion to dixanthogen, adsorption and reduction of the dixanthogen to a chemisorbed lead xanthate species. In paper I of this series (11) it was shown that the thiosulphate ion, which forms on galena surfaces in slurries at the pH normally used for flotation, will reduce dixanthogen. There is, therefore, the impasse that the electrochemical evidence requires that xanthate ion be oxidised to dixanthogen at the galena surface while the chemical evidence shows that the reverse reaction takes place.

Jan 1, 1973

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By Lawrence P. Kennedy

The Lynne deposit is a volcanic-to volcaniclastic-hosted, Zn-Pb-Cu-Ag orebody located in the early Proterozoic magmatic terrain of northern Wisconsin. As of February 1991, core drilling has partially delineated a multi-million ton, near-surface, disseminated to massive sulfide deposit. The deposit is hosted by a gently dipping sequence of fragmental rhyolites, felsic tuffs, less abundant dacite to andesite flows, and fine-grained volcanic sediments. The deposit is broadly conformable With the host rock stratigraphy, but the ore zones thicken and coalesce in the central part of the deposit.

Jan 1, 1991

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By William L. Young

I think I should let you in on one of Canada's best-kept secrets, if you will promise not to tell it all over the place. Believe it or not, good, honest, enterprising capitalism is still alive and flourishing north of our common border, and I am living proof that capitalism is still working for the little guy. My personal story of mining development in Canada isn't all that rare -- you've probably heard something like it from other areas and other days several times -- but my case brings it up-to-date. I would like to Tell you briefly the history of Northumberland Mines Limited, a contemporary case of individual enterprise getting a mining operation underway. And if I can do it you probably can too.

Jan 1, 1981

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023