Search Documents

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By Crone Duncan

The search. for massive sulphide orebodies is steadily being extended to greater depths as well as expanding outward into the large portion of the earth's surface where the sulphide bodies are deeply weathered. Massive sulphide orebodies are generally not large in dimensions. They are not like disseminated type sulphide bodies that form large ground exploration targets that can be detected at greater and greater depths simply by increasing the geometrical spacing between the geophysical transmitter and receiver. In¬creasing the transmitter-receiver spacing with massive sulphide bodies eventually "waters down" the anomaly from the body until it disappears into noise. If high surface conductivity is present, as is common in areas of deep weathering, the problem is compounded by the increasing response of the surface layer, as the receiver-transmitter spacing is expanded. The search to greater depths has important implications other than just detection of the orebody. Drilling costs are increased and the probability of missing the target are increased. Missing an orebody is an expense that is difficult to evaluate in dollars per line mile of survey especially since one does not know the value of what was missed. A ground Pulse EM method has the capabilities of solving the problems of deeper exploration particularly in areas of surface weathering it can attain deep penetration without large coil spacings, it also provides information from a complete range of frequencies. The method has other operational advantages since it is free of geometrical restrictions as to coil alignments and can operate in areas of high power line noise.

Jan 1, 1975

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By Paul Dean Proctor

The world's population by 2000 A. D. may approximate 6.5 billion and the United States' 304 million. South Asian population increases between 1970 and 2000 A. D. will be triple the projected population of North America. Such anticipated dramatic and probably traumatic increases in world population yield grave concern for the standard of living in the world and the United States. The people of the United States currently consume 32 percent of the world's energy and similarly large percentages of the world's mineral raw materials. With only 6 percent of the present world's population and slightly smaller percentage by 2000 A. D., much expanded world-wide production of energy and raw materials will be required to maintain even a standstill living standard. A minimal 2 percent increase per year in the standard of living in the United States and a 4 percent increase elsewhere in the world, beyond the demands of the estimated population increases, suggest the magnitude of the increased need for energy-mineral raw materials and the possible crises the world will face in these areas by 2000 A. D. Mineral engineers and scientists with broad educational backgrounds will be required in greatly increased numbers to help alleviate, and possibly avert, expected energy-mineral raw materials shortages of the next millenium. Explorationists, mineral engineers, commodity economists, environmentalists, city, county, state, and federal mineral materials planners and coordinators, and metallurgists will be among those most needed. AIME membership in the second century of the Institute's history will contribute directly to this personnel pool.

Jan 1, 1971

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By Bill A. Hancock

In Situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of In Situ leaching into a sophisticated system has gained new impetus. In Situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for our nation's energy heeds. In this paper, I will be giving an overview of the merits of the system, as well as the technology, problems, and research in solution mining of uranium.

Jan 1, 1977

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By R. C. Bunge

The success of a mineral separation is commonly assessed from the separation curve, a graph of the recoveries achieved versus the corresponding separator settings. Two values characterize the curve, first the "splitpoint" which is the separator setting that produces a recovery of 50%, and second a measure for the separation sharpness. The splitpoint represents the "mean" while the measure for the separation sharpness represents the "scatter". In modelling the performance of crossflow separations the mean particle behavior is calculated from the force equilibrium that determines the particle trajectory which leads to a deterministic model. The scatter is then represented by a stochastic model. This presentation discusses the modeling of a crossflow separation and some implications with separation theory. The model is shown to successfully predict the performance of a magnetogravimetric separator.

Jan 1, 1992

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By J. E. Russell

The purpose of this paper is to describe an independent study which forecasts Texas coal production, specifically for electric power generation. This study, extending to the year 2000, is justified on the following basis. Texas produces and consumes considerably more electric energy than any other state, has consistently high growth rates in the population and industrial sectors, and has large lignite reserves. Also, since recent forecasts have been criticized as overly optimistic, this study is timely when considering the long lead times required in obtaining new power sources. In the study demand for electric energy was assumed to rest on two dominant factors: 1) overall state of the Texas economy as measured by the Texas Gross State Product (TGSP) and 2) Texas population. Demand models were prepared and tested following a study of several options. A final linear regression demand model with time lags for the two variables was chosen on the basis of good correlations. On the supply side, uncertainties such as impact of nuclear sources, gas-fired cogeneration, and ratio of imported to lignite coal exist. These uncertainties were studied with high and low cases for effects on lignite. Finally a simple supply model was chosen. Results of the study indicate that lignite production in Texas will rise from the current (1984) 40 million tons per year (XTPY) to the range of 77 to 124 MTPY and more probably 100 HTPY in the year 2000.

Jan 1, 1984

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999