Search Documents

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By C. Dale Elifrits

Observations made from laboratory analysis of samples of fine-grained argillaceous materials (shales) subjected to various changes in moisture content have been correlated to loss of strength in the rock material. This reaction to a change in in-situ conditions (subsequent to mining) at a mine site combined with the observed relationships of surface-disturbing subsidence features at locations where the predominant overburden material is fine-grained, provides a predictive tool for the subsidence engineer.

Jan 1, 1983

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986

By M. A. Mahtab

This paper presents the results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block-caving method. The two-dimensional finite element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1975

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem' in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By M. Kehnemuyi

The U.S. Department of Energy is charged, by federal law, with the responsibility for developing and implementing programs for long- term storage and terminal disposal of high- level radioactive wastes from both commercial and defense nuclear operations. Approximately 288,000 cubic meters of defense high-level wastes are currently in storage at the government's Hanford Reservation in the State of Washington, the Savannah River Plant in South Carolina, and the Idaho Chemical Processing Plant in Idaho (U.S. Department of Energy, 1980a). High-level wastes from commercial nuclear power production are stored in water pools or basins at various power plant sites. At the end of 1980, approximately 7.460 metric tons of uranium, contained within 28,300 fuel assemblies was in storage at various reactor basins. Although the present inventory of defense wastes are many times larger in volume and in total level of radioactivity than the commercial wastes, in the future, the latter will constitute a substantial quantity of wastes that will have to be disposed of. The present electric generating capactiy of nuclear power plants in the United States is 56.5 Gigawatts-electric (GWe). The amount of spent fuel that would be discharged and accumulated by the year 2000 from these operating reactors would be 38,000 metric tons. With a projected growth of the nuclear industry to 180 GWe in the year 2000, the amount of spent fuel accumulated at the turn of the century could reach 89,000 metric tons of uranium or approximately 318,000 assemblies. In any case, whether one postulates a no growth pattern or one where nuclear power provides its share in the country's electric generating capacity in the next two decades, a means for safe and environmentally accept- able disposal of high-level nuclear wastes must be found. Storage of commercial wastes in water basins, either at reactor (AR) sites or at away from reactor (AFR) sites, and storage of reprocessed defense wastes in surface or near surface tanks is a temporary solution and is not an alternative for permanent disposal.

Jan 1, 1981

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By J. L. Roll

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) and the regulations promulgated for that "Act" have resulted in changes to surface mining operations in order to comply with the stringent federally enforced reclamation requirements for prime farmland. In many instances the operator has modified surface mining operations to meet the prime farmland requirements through changes to mining equipment operation, addition of new equipment targeted for reclamation or the use of totally different mining techniques. The major challenge to mine operators has been how to use existing mining equipment to meet the requirements of the "Act." Freeman United Coal Mining Company opened the first new large surface coal mine in Illinois following passage of the "Act." The Industry Mine, located near Macomb, Illinois started mining operations during March of 1982 and was required therefore, to meet all of the requirements of the "Act" including prime farmland restoration. At the Industry Mine a shovel and a cross-pit bucket wheel excavator (wheel) are used for overburden removal and the wheel is addition- ally utilized to assist in reclamation operations. The wheel mines the subsoil thereby elliminating scraper placement of that subsoil and the attendant compaction problems with scraper placed subsoil. The wheel is used to convey topsoil stock- piles from the highwall to the mined overburden in order to lessen scraper traffic and possible compaction on the graded overburden during top- soil removal and replacement. Close control of the operation of the wheel yields more uniform wheel spoil ridges which then require less grading prior to topsoil replacement.

Jan 1, 1986

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By Wayne Hilgedick

Peabody Coal Company is the nation's largest producer of coal and is headquartered in St. Louis, Missouri. In 1978 Peabody divisionalized its operations to establish more responsive and effective mine management. Peabody Coal Company's Arizona Division operates two large surface mines, the Black Mesa and Kayenta Mines. Both are located in northeastern Arizona, approximately 30 miles from Kayenta, Arizona, on the Navajo and Hopi Indian Reservations. The Black Mesa Mine produces 4 to 5 million tons of coal per year and the Kayenta Mine produces 7 to 8 million tons per year. Coal from the Black Mesa Mine is transported 274 miles by coal slurry pipeline to the Mohave Generating Plant located on the Nevada/Arizona border at Bullhead City, Arizona. This plant is jointly owned by Southern California Edison, the Los Angeles Department of Water and Power, Nevada Power Company and Salt River Project Agriculture Improvement and Power District.

Jan 1, 1983

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

By Donald E. Steif

The Tower Mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine, its operation, application, and performance for wet grinding.

Jan 1, 1984