Search Documents

By G. Bitsianes

An experimental procedure was developed for studying magnetic roasting on a accurately-controlled laboratory scale. The loss-in-weight method was used and the course of reduction could be followed under a reducing gas atmosphere containing as many as five different components. Some important variables of the operation were checked on a marginal Mesabi iron ore containing porous and dense varieties of hematite as well as pure goethite. The conditions simulated were those for the grate roasting of a coarsely-sized ore burden. Temperature was maintained at 600°C; gas composition at 4.25% CO, 4.25% H2, 17.0% CO2, 15.0% H20, and 59.5% N2,, and gas flow rate at about 1,5 lineal feet per minute. The ore charge was composed of quarter-inch cubes. Under these conditions, the ore porosity was found to be one of the governing variables of the operation. Results showed that an ore size limitation existed as a function of this ore porosity. For efficient magnetic conversion, the size limit was 3/8 inch for very porous ores and about 65 mesh for very dense ores. An anomaly was noted in the weight losses incurred during actual magnetic conversion. For goethitic ores, these were generally about 13 per cent higher than could be accounted for theoretically. The effect was attributed to possible non-stoichiometric structures forming during the reduction process.

Jan 1, 1960

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By R. Fedel-Moen, R. W. L. Kimber, B. D. Williams, S. R. Ragusa

The use o f cyanide to extract gold from ores is widespread. In the process of extracting gold, cyanide may form metal cyanide complexes with a variety of other metals present in the ore. This study was carried out to investigate the biodegradation of the Cu(I)-cyanide complex and tetracyanonickelate under varying pH and nutrient additions. Detailed studies using shake flask cultures and bioreactors showed that naturally occurring bacteria residing on gold-leach-pad ore uti¬lized the Cu(I)-cyanide complex (CuCN) and tetracyano-nickelate, Na2(NiCN4), as carbon and/or nitrogen sources. Ammonium-nitrogen (NH4+-N) and/or cyanate (CNO-) accumulated in solution as the metal cyanide complexes were degraded. The accumulation of cyanate as a product is a concern due to its toxicity. Degradation rates were increased if a growth substrate (peptone, 0.1%) was added to the medium or if bioreactors were primed with peptone before addition of the metal-cyanide complex. Tetracyanonickelate was degraded at pH 8 without added peptone, but it was not degraded at pH 10. The addition of peptone was required for degradation of the Cu(I)-cyanide complex at pH 8 and pH 10. At pH 8, the addition of peptone resulted in the accumulation of cyanate, whereas, at pH 10, cyanate was not detected in the cultures. Biodegradation of metal-cyanide complexes was faster (approximately 1.5 to ten times faster) in bioreactors than in shake flask cultures. The addition of peptone was not required for degradation of metal-cyanide complexes in bioreactors. However, priming the bioreaetor with peptone resulted in higher metal-cyanide degradation rates over multiple cycles.

Jan 1, 2000

By Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comninution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5 x 6.4 m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790 to 1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By David S. Young

All pigments and extenders or fillers whether organic or inorganic fall into the following broad general classes: I. Colored II.-White III. Black IV. Metallic A pigment- is any particulate matter that is essentially insoluble and chemically unaffected by the media into which it is dispersed. According to this very broad definition, colored pigments, white pigments, fillers, extenders, and functional pigments would all be included. The particulate size range would also be quite broad ranging from very fine colloidal particles (~0.01µ) to relatively coarse particles (~100.0µ). This broad definition is usually subdivided into more practical divisions which tend to relate the classification of the pigment to its primary function in the system in which it is used. Hence, the word extender implies that its major purpose may be to extend the system.

Jan 1, 1985

By J. D. McKay

Continuous column flotation parameter testing, to improve operating methodologies, using coarse bubbles on fluorite ore from Nevada, revealed that retention time is the predominant factor affecting column flotation fluorite recoveries. Column height and feed injection location affected fluorite grades and recoveries because they affected particle retention times in the collection and cleaning zones. Other parameters tested, including froth depth, wash water addition, and axial mixing, showed varying results. Four defined zones within the column were found to have characteristic rates of upgrading per vertical foot. Fluorite-gangue separation was more efficient in a column than in a conventional cell at all particle sizes.

Jan 1, 1987

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By C. E. Jordan

Abstract. The U.S. Department of the Interior, Bureau of Mines, as part of its effort to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, is conducting research on the pneumatic recovery of coarse mica. A system of crushers, screens, and zigzag air classifiers is used to concentrate coarse liberated mica particles from mica ore and from the waste tailings of abandoned mica operations. The plus 0.21-millimeter-size mica is effectively recovered by this method. The mica concentrates produced contain over 90 percent mica. The method recovered up to 78 percent of the mica in the samples. As a dry concentration method, the pneumatic-beneficiation technique may be advantageous in areas of limited water resource.

Jan 1, 1980

By Patrick Browne

Drilling programs and the study of active geothermal systems have shown that the reservoir rocks in many fields contain minor quantities of base and precious metals. Commonly, base-metal sulfides occur in the subsurface but, where present, Au, Ag, Hg, As, T1 and Sb rich precipitates deposit near, or at, the surface. Although in some fields (Geysers, Larderello, Tongonan) some of the ore minerals (and others) are relict, there is evidence that they are now depositing in a few systems. Recent work on active hydrothermal systems in New Zealand shows that: (1) Sphalerite, galena, chalcopyrite (forming veins and disseminated discrete crystals) plus rare pentlandite, cobaltite and arsenopyrite, occur at Broadlands, NZ. Rare quantities of base-metal sulfides also occur in cores and cuttings from the geothermal fields of Waiotapu, Kawerau, Tauhara, and Ngawha. Further, Kakimoto (1983) has identified cassiterite, native silver, and trace gold in cores from Tauhara, in the south-eastern part of the Wairakei field. Bore temperatures at the depths from which these minerals were recovered are mostly between 220° and 300°C, but at Broadlands are locally as low as 120°C. The host rocks are Quaternary talc-alkali, silicic lavas and pyroclastic rocks, andesites, dacite and deep Mesozoic greywackes and argillites; however, there is no obvious relationship between mineralization and stratigraphy, permeability or well output. (2) The deposition of amorphous precious metal precipitates (Au, Ag, Hg, As, Sb, T1) from hot springs and well discharges has taken place at Broadlands, Waiotapu and Rotokawa; it also occurs at Kawerau. (3) Water discharging from Frying Pan Lake, Waimangu, is presently depositing siliceous sinter containing up to 4.1% tungsten. A characteristic of mineral-depositing fluids in the New Zealand geothermal fields is their very low salinity (total dissolved salts of 3000 ppm or less but with high CO2); they are of near- neutral alkali chloride composition, although water discharging from Frying Pan Lake has a pH of 4.5, and very low metal contents. Very effective concentration processes (10 times for gold at Broadlands) must occur: in the subsurface these include boiling and rapid cooling but near, and at, the surface, mixing of waters of different pH seems to dominate. In particular, descending acid condensate, derived from separated steam and oxidation of H2S mixes with its parent alkali chloride water, resulting in precipitation of amorphous ore metals. Base-metal sulfides also occur in veins and as disseminated grains in geothermal fields at Tongonan, Leyte and Southern Negros, Philippines. These fields have a porphyry-type setting with host rocks of Miocene andesitic lavas and pyroclastics intruded by diorites so that the fields have undergone complicated thermal histories before cooling to their present base temperatures of about 325°C. Precious metals have precipitated from waters from some wells (Leach, pers. comm.) but they do not, as yet, form ore-grade deposits.

Jan 1, 1984

By S. P. Singh

In order to simulate the operation of coal extraction machines, a portable workability instrument has been designed. Initially, the tests were performed with the instrument on modeling material, which were followed by in situ tests on coal in underground mines. The peak and mean cutting resistance and work done to cut a unit length of coal were determined for coal as well as modeling material. In addition, rebound strength and dynamic penetration tests were also performed in situ. On the basis of the cutting characteristics of coal, a "Workability Index" has been developed and its role in the judicious selection of coal cutting machines has been discussed. With reference to prior works and the strength characteristics of coal, it was found that the coal plow may not be suitable for the seams under investigation and the shearer seems to be the only choice. It has been observed that peak cutting resistance and the "Workability Index" in the case of coal as well as modeling material depend upon compressive strength. The peak cutting resistance exhibited certain dependence upon the Schmidt rebound hardness and dynamic penetration strength of coal in situ.

Jan 1, 1984

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966