Search Documents

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By C. A. Born

AMAX Inc. climax's mine-mill complex at Climax, Colorado is best known for its molybdenite production: 50,000 TPY of molybdenite flotation concentrate (95% MoS2) from mill heads containing 0.35% molybdenite. Less recognized are the byproducts that are concentrated from the tails generated in the rougher flotation circuit (see Figure 1). Climax recovers a heavy mineral concentrate by passing the rougher tailings from molybdenite flotation over Humphrey spirals (Figure 2a). This concentrate is floated using xanthate at pH 4 to remove sulfides, principally pyrite. The tails from the pyrite float are then cleaned of quartz, feldspar and light minerals by tabling (Figure 2b). Amine flotation follows at pH 1.5 and 75°C to float monazite (Figure 2c). The present circuit at Climax dries the monazite flotation tailings and utilizes high intensity cross-belt magnetic separation Figure 2d) to generate a high grade wolframite concentrate and a low-grade cassiterite product, both of which are contaminated with the mineral brannerite, (UO, TiO, UO2)TiO3. The uranium specifications have recently become difficult to meet due to the increasing percentage of brannerite reporting in the mill feed. A plant is being built utilizing hot sulfuric acid and sodium chlorate to leach this uranium from the monazite flotation tailings prior to their being fed to the wolframite- cassiterite magnetic separators. This modification is the subject of our paper.

Jan 1, 1975

By P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous Chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By T. H. Ueng

Solving ventilation networks of natural air splitting is a classical problem in mine ventilation. A common approach to this problem is to formulate it based on Kirchhoff's voltage and current laws and obtain the solution by an iterative technique known as the Hardy Cross method. In this paper, it is shown that the problem can be formulated and analyzed as an unconstrained optimization (minimization) problem. The computational experience with the method of conjugate gradients is also discussed.

Jan 1, 1984

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By Layton C. Binon

Exploration budgets are commonly determined by "rules of thumb" such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve the goals of the company. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1981

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By Xiaochao Shu, Kun Wang, Fanwei Meng, Rui Tao

Rapidly searching for carbonatite-related rare earth element (REE) mineralized systems is of paramount importance to explorers, because these systems provide the world’s most significant supply of REE. Biotite and barite are suitable indicator minerals that can offer reliable elemental geochemical information used for REE exploration. In this study, we provided an elemental geochemical dataset of biotite and barite from Cenozoic REE deposits in the eastern Tibetan Plateau, and compared the obtained data to those of biotite and barite forming in other geological settings. The F (i.e., fluorine) contents in carbonatite-hosted biotites are highly variable, with biotites from mineralized carbonatite complexes having much higher values (1.05–2.37 apfu, where apfu = atoms per formula unit) than their counterparts from barren carbonatite complexes (≤ 1 apfu). It is therefore believed that the presence of high-F biotites can be regarded as a sign for predicting REE reservoirs. Barites in REE mineralized systems contain much higher (even one or to orders of magnitude) total REE contents (ΣREE >100 μg/g) relative to those species forming in carbonate-hosted fluorite-barite deposits and open marine environments. This means that the high ΣREE concentration of barite can serve as an effective index for REE exploration. The above information is integrated into a REE exploration program in which the areas with strong local tectonism along cratonic edges are priority exploration targets, and high-F biotites and REE-rich barites can serve as direct indices for rapidly identifying carbonatiterelated REE mineralized systems at a strategic distance from other geological settings.

Jun 9, 2023

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By B. Arvidson

Computer-controlled machine sorting may, if properly applied, have a dramatic effect on overall economics of a mine operation. Radiometric and photometric sorters have been used for many years and new developments will be reported, such as a sorter for fine particles and a conductivity/magnetic sorter. Application examples with emphasis on precious metals will be given. Economics for some of the projects will be reviewed and discussed. Sorting underground is shown to be particularly attractive, but machine sorting would be profitable in most cases based on savings in transportation and milling/beneficiation costs only.

Jan 1, 1987

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012