Search Documents

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By Gordon M. Bell

Water has received little attention as a variable in flotation, even though it is a known fact that water hardness often has an adverse effect on purity and recovery, particularly on the flotation of non-metallic minerals. Because of this fact, process water used in some flotation plants is treated to reduce hardness to an acceptable level. In the laboratory, distilled water is usually used as the flotation medium in order to standardize conditions, whereas in flotation plants locally available water is used. At Rosiclare Works of Aluminum Company of America, Rosiclare, Illinois, where a vein-type of fluorspar deposit was being processed by flotation to make an acid-grade fluorspar concentrate until February of 1968 when the plant was closed, qualitative correlations had been observed between metallurgy and reagent consumption and the seasons of the year. The observed effects were thought to be due to seasonal variations in the quality of Ohio River water used as the flotation medium. Figure 1 shows the variations in total hardness and chloride contents of Ohio River water at Rosiclare for the period September 1964 through September 1967. During this period, the sulfate content varied from 85 to 245 ppm (as Na2SO4), the calcium from 90 to 160 ppm (as CaCO3) and the magnesium from 50 to 70 ppm (as CaCO3). The data in Figure 1 show that the total hardness and chloride contents are highest in the late summer and fall which are usually periods of low water and lowest in late winter and spring which are usually periods of high water.

Jan 1, 1970

By G. Ahuja

Tests were conducted to investigate the effects of cyclone geometry, operating conditions, and particle size on magnetite classification. The effects of these parameters on the partition curve for narrow size fractions were studied using a 25mm diameter cyclone cleaning -150 µ m coal. Additional tests were run to investigate the effects of geometry and operating conditions on the slurry, solid, and water splits. The relationship between the relative density of the underflow stream and the relative density of separation was also investigated. This paper presents the results from this study.

Jan 1, 1994

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967

By K. Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1993

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

By Paul Piercy

Bougainville Copper Limited operates a porphyry copper mine in Papua New Guinea. The waste dumps will contain 400 to 500 million tomes of rock at the end of nine life. The paper describes investigations carried out over a period of en years and highlights the problems associated with waste lump leaching in a tropical and seismic active region. Aspects discussed include mineralogy, chemical reaction, leaching rates, microbiological activity, dump stability, dump structures, effects of tropical conditions, seismic activity and topography.

Jan 1, 1981

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By Georgene Renner

Due to disturbance of their traditional roosts, caves and tree hollows, more than half of the 44 bat species found in the United States and Canada now live in abandoned and inactive underground mines. The North American Bats and Mines Project was created two years ago by Bat Conservation International Inc. (BCI) in Austin, TX and the Bureau of Land Management (BLM) in response to the issue of mine closure and bat habitat. The partnership provides national coordination among government and private agencies and the mining industry to minimize the loss of bats living in mines. It also trains land managers on how to conduct cost-effective mine assessment and closure to protect both bats and people.

Jan 1, 1996

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By J. A. Mielczarski

An infrared external reflection spectroscopy (ERS) technique has been developed to study the structure of the adsorbed layer of ethyl xanthate formed on copper and natural chalcocite (Cu2S) electrodes. The infrared technique provides information concerning the identity and the orientation of the adsorbed species at monolayer and submonolayer coverages. X-ray photoelectron spectroscopy (XPS) studies have also been conducted to monitor changes at the surface. The results show that the first oxidation peak on the voltammograms for copper and the first and second oxidation peaks on the voltammograms for chalcocite electrodes are not characteristic of a chemisorbed xanthate species, which is contrary to what has been reported by other investigators previously. As evidenced by the XPS spectra, there was an increase in sulfur relative to copper on the copper and chalcocite surfaces over the potential region where these oxidation processes occur. The spectroscopic results (ERS, XPS) indicate that the second and third (on copper) and the third and fourth (on chalcocite) oxidation processes recorded on the voltammograms are due to cuprous ethyl xanthate adsorption. The orientation of the adsorbed molecules of xanthate was observed to change with increasing surface coverage. Therefore, it has been concluded that xanthate can modify the copper and chalcocite surface in two different ways. At lower potentials, xanthate is a source of sulfur for the formation of a sulfur-rich surface. At higher potentials, an adsorption layer of cuprous ethyl xanthate is formed. Contact angle measurements show that both of these processes of xanthate surface modification lead to an increase in the hydrophobicity of the substrates.

Jan 1, 1990

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By Haydn H. Murray

Although alumina constitutes about ii percent of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception off the alumina in bauxite. The United states has a variety of non-bauxite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline syenite. Each of these resources are discussed from the standpoint of geology, geography, processing, potential recovery, and environmental problems. Potential by-products include silica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1982

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By Tim O’Neil

Nearly 4,800 mining professionals and exhibitors occupying 580 booths attended the 2000 SME Annual Meeting and Exhibit, Feb. 28-March 1, in Salt Lake City, UT. The technical program included80 sessions and four specialty symposia: bulk material handling, control 2000, minor elements 2000 and plant operaters. Meeting highlights included the keynote session. Executive shared their perspectives on pivotal issues and approaches to address the challenges of the new millennium. SME has begun planning for its 2001 Annual Meeting, Feb. 26-28, in Denver, CO. The meeting carries the theme “2001 — A Mining Odyssey.” A call for papers has been issued and exhibit space is 80% reserved. For information, visit SME’s website, www.sme-net.org. Or write Box 625002, Littleton, CO 80162-5002,ph 800 763 3132 or 303 973 9550, fax 303 979 3461, or email meetings@smenet.org.

Jan 1, 2000

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By M. R. Yalamanchili, W. H. Jang, Y. Ye, J. D. Miller

Typically, rougher molybdenite flotation and recovery from bulk copper/molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment to depress copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40% and 90% at a concentrate grade of 5% to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Mo concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning resuIts in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/fotation strategy, the process is technically and economically viable and should be suitable for industrial ap¬plication.

Jan 1, 1991