Search Documents

By H. Colijn

The problem of the freezing of moist raw materials, such as concentrates, in railroad cars during winter shipment has been a continuing source of both economic and operational trouble to the industry and to the railroad companies. The difficulties center around the discharging of frozen cargoes into the plant materials handling system. Because of cargo freezing, appreciable delays in car-dumping schedules occur each winter and cause additional expense for demurrage charges and for slowdown of plant operations. In one plant during one winter, a car dumper rated at 40 cars per day could dump only 3 cars per day in bad weather. Delays became so serious one winter, that 500 cars held in the yard became so badly frozen, that they were sent to the southern part of the United States to thaw after they accumulated an average of two months demurrage charges. These delays in car unloading become critical if unit or integral train concept is applied to the movement of raw materials. Anticipated savings in transportation costs through better equipment utilization are largely based on rapid loading and unloading cycles of whole trainloads. If freezing problems cannot be adequately solved, unit train operations cannot be operated to achieve the potentially large reductions in transportation costs. The freezing problem may tend to become even greater in the years ahead, because the unit train concept will allow the trains to run faster and consequently the heat loss will be accelerated due to the larger heat transfer coefficient. A compensating factor, however, will be the shorter travel time. Further, the sources of raw materials being mined are located farther north than before and the ambient temperatures during transit are going to be lower.

Jan 1, 1976

By Ashis Bhattacherjee, Bijay Mihir Kunar

A literature review on quantitative analysis of mine safety studies revealed that investigators use a wide range of statistical techniques for the analysis of mine injury data. Researchers have addressed the various issues of accident causation and prevention through analysis of mine injury data collected from mines. These studies are generally based on historical accident/injury data without considering the injured person/population at risk. In this paper, a public health approach, based on scientific methods of epidemiology, is presented to address mine safety issues. Epidemiology is the scientific study of disease and injury patterns among populations in time and space. Originally, epidemiology was concerned with epidemics of communicable diseases. Then it was extended to non-communicable diseases. Safety researchers found that epidemiologic methods are the best tools for injury research, because the occurrences of injury and the occurrences of disease are quite similar. As a result, some researchers started applying this concept to injury research. This paper presents some of the techniques used in epidemiologic studies and illustrates the application of a case-control study design to evaluate the role of some risk factors associated with injuries in underground coal mines. In this study, the injured persons were identified and, simultaneously, interviews were conducted to find the significant risk factors responsible for occupational injuries in coal mines.

Jan 1, 2011

By Shiou-Chuan Sun

Notwithstanding the fact that unsaturated fatty acids are used in preference to saturated acids for most flotation purposes, information regarding their collecting properties is sketchy. Keck, Eggleston, and Lowry1 reported in 1939 that the collecting power of fatty acids on hematite decreased in the order of oleic, lauric, myristic, palmitic, and caprylic acid. Keck and Jasberg2 described in the same year that "unsaturated oleic acid with 18 carbon atoms was a better collector than saturated stearic acid" for floating magnetite. Gaudin and Cole3 stated in 1953 that the double bonds of oleic and linoleic acid were not oxidized during the flotation of fluorite, whereas the double bonds of linolenic acid were measurably altered even after one single flotation step. In August, 1953, Hukki and Vartiainen4 concluded that the collecting power of palmitic, oleic, linoleic, and linolenic acids on ilmenite, magnetite, pyrite, and rutile increased with an increasing number of double bonds in the acid molecules. This was subsequently proved to be generally true for the flotation of mapganese5, phosphate6, and magnetite7. The above cited literature indicates that, prior to the present paper, only about ten minerals were tested with pure unsaturated fatty acids as collectors.

Jan 1, 1959

By R. D. Hansen

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures do exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers end some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1985

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry's remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy's efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By A. Heriba

Cyanide is highly toxic to humans and other organisms. Concentrations of RCN as low as 0.05 ppm can be lethal to fish (Scott and Ingle', 1981). In wet climates and in colder climates where natural degradation is slow, it is becoming mandatory to destroy cyanides in effluents before they can be discharged. The disposal of spent gold ore as tailings from cyanide heap leach processing facilities is a matter of concern to the public, the mining industry, and regulatory agencies. South Dakota mining laws and regulations require that spent ore be neutralized to a suitable level with respect to cyanide before disposal (Durkin, 1990). To safeguard the environment and protect ground-water and surface-water supplies adequately, a reliable test is needed to determine the amount of cyanide in the solid spent ore.

Jan 1, 1993

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By Brianna Eiter, Max Barham, Tim Bauerle

Fatigue-related risk is a persistent safety concern for the mining industry. However, fatigue and sleepiness are often treated interchangeably, which can lead to confusion and potentially less effective reduction of safety risk. To provide clarity, we present an overview of similarities and differences between work-related fatigue risk and sleepiness including definitions, theories, measurements, and mitigation strategies. As a supplement, a summative visual model which highlights these similarities and differences is presented. Expanding industry knowledge in this area will assist safety professionals in crafting more targeted risk management practices appropriate for work-related fatigue risk, sleepiness, or both.

Dec 19, 2023

By Kazumasa Taguchi

At the Kakogawa works of Kobe Steel. Ltd., the agglomeration facilities are composed of a pelletizing plant and sintering plant. This aim is to utilize raw materials efficiently and stabilize the raw material resources. Therefore at Kakogawa works, the blast furnaces (BF) have been operated with high pellet ratio and various developments for pellet properties have been achieved to improve the blast furnace performance. These developments include dolomite-fluxed pellets, new-porous pellets and crushed pellets. As a results of these improvements, pellets have achieved almost the same performance as sinter at high temperature regarding properties such as the softening, melting and reduction behaviour. However, some problems on shape have remained to be solved. Spherical pellets flow easily into the center of the furnace and form mixed layers of pellets and cokes. Therefore, in BF operations with these pellets it becomes more difficult to keep proper and stable gas distribution.

Jan 1, 1983

By Alexander N. Winchell

"Location. The Cuyuna iron district extends from the region of Kimberly, near the Center of Aitkin County, Minnesota, south-westward through Deerwood, Ironton, and Brainerd, across Crow Wing and Todd counties, across the Mississippi River, and for an unknown distance farther southwest in the same direction. It is known that the Huronian rocks, in which the ores of the Cuyuna district are found, reappear near the western border f Minnesota, but no ores have been found in this region. The district has a length of more than sixty miles, but the more important portion as now known 'is confined to Crow Wing County in an area which is less than thirty miles in its longest dimension. The commercial headquarters for the district are in the city f Brainerd, on the Mississippi River.History. The discovery of iron ore in the Cuyuna district was accomplished with no aid from surface outcrops, but solely through the use of the dip needle. The mantle of glacial drift overlying the iron formation varies from twenty-five to 359 feet in thickness, and it was by means f the magnetic attraction of the iron bearing rocks that their presence was discovered with the dip needle by Cuyler Adams, about 1895. The general geologic map of Minnesota, published by the State Geological Survey in 1909, showed the extension of the Huronian rocks of the Mesabi district passing through this area. Two years later, Leith published a sketch showing the hypothetic extension of the iron bearing formation through the same area. The first drilling was done in 1903, near Deerwood, Minn., by Cuyler Adams, and exploration was continued to the present time in increasing amount. The Northern Pacific Railway extends throughout the length of the district and affords an easy outlet for the ores. The Soo Line Railway completed a spur into the district in 1910. Both roads carry the ore to the docks at Supe¬rior, Wis., the average haul being about ninety miles. Shipments began in 1911, the Kennedy mine being the first producer. By 1918, the number of shippers reached twenty-seven, with a total output of nearly two and one-half million tons for that year."

Jan 1, 1920

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By Joaquin Ruiz

Naica consists of at least 10 mantos and 40 chimneys that have produced over 15 million tens of ore with 10% Zn, 13% Pb and 13 oz/ton Ag. The ore occurs in thick-bedded, folded Cretaceous limestone. Fractures and 26 Ma old felsite dikes with an initial strontium isotopic ratio of 0.708 localize the mineralization. The mantos follow the dikes and have abundant early skarn with manganohedenbergite, calcic garnet, idocrase, quartz, calcite, wollastonite, schellite and later sulfides. The chimneys arise from the mantos and change from silicate-rich to silicate-free sulfide limestone replacements. Carbon, oxygen and sulfur isotope data on carbonates, silicates, sulfides and sulfates are compatible with a single evolving (magmatic?) fluid.

Jan 1, 1985

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

By T. I. Martinovic

A major investigative' program was conducted on the development of an acceptable substitute organic binder for bentonite for the pelletizing of the Iron Ore Company of Canada's Carol concentrate. The first phase of the program covered an evaluation of several organic binders in laboratory tire balling in order to identify the most promising potential organic binders. Based on the green ball quality obtained, Peridur C-10, Alchem 8C26 and peat moss were selected for full scale pot-grate testwork. The selected binders were tested with various pelletizing mixes (acid, dolomite, limestone and fully fluxed). The pot-grate test results showed that an acceptable pellet quality can be produced with the use of Peridur C-10.

Jan 1, 1989