Search Documents

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

By A. K. Sinha

Despite the tremendous efforts and costs incurred by the industry and regulatory agencies to prevent premature roof failures in underground mines, roof falls continue to occur frequently due to the very unpredictable geological conditions and dynamic nature of mining operations. In fact, roof falls continue to be the largest contributor to coal mine fatalities. The failure of a mine roof generally occurs following a prolonged, gradual degradation in its physical conditions. An electronic mine roof monitoring system has been developed and tested in operating mining sections. It monitors mine roof degradation on a continuous basis. The field test results are presented and discussed.

Jan 1, 1987

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By Ed L. Schrader

Kaolin of the Georgia-south Carolina "Clay Belt" are used in a wide variety of filler and extender applications. Sane applications specifically require the performance enhancement delivered by incorporating kaolin into the product formulations. Other applications are less specific in requirements for an inert mineral filler. In order to be a feasible candidate for filling and extending, a mineral or mineral product must be generally inert (except where specific interaction with the filled medium is desired), inexpensive, easily handled and transported in a variety of forms, accessible to a broad segment of the desired market, and must exist in sufficiently large ore reserves as to assure production for many years. Of course, more precise requirements are necessary in specific applications of a prospective filler material.

Jan 1, 1985

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection&apos;units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer&apos;s preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By Walter E. Kramer

The advantages derived from the use of pellet burdens in blast furnaces are so great, that hematite ores are being converted into pellets in greater quantities each year. The conversion of these ores into pellets appears on the surface to be relatively simple. In reality, this is not so. Serious difficulties are encountered in drying these pellets that do not exist in the drying of taconite concentrate pellets. The ores that present problems are goethite and earthy hematites. Green pellets prepared from these ores have very law shock temperatures, 200-600° F. The shock temperature of a green pellet according to our definition is the highest initial temperature to which a green pellet may be exposed without suffering decrepitation. Decrepitation may involve spalling, fracturing or total disintegration. The poor shock properties of these green pellets result from the inability of the vaporized water to escape freely and easily as it is formed with¬out affecting the integrity of the pellet. As a consequence, the pellets must be carefully dried prior to induration. This careful treatment is costly. The slow drying process restricts productivity and requires larger furnaces than desired. The use of an additive to elevate the shock temperature of the green pellets would increase productivity. Bentonite is used in some pellet plants to improve balling but it raises the shock temperature only slightly. Nalco became interested in the shock temperature problem because of its activity in the development of organic pelletizing aids for taconite concentrates. The findings reported here are an outgrowth of our experimental work on the development of shock temperature additives.

Jan 1, 1967

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Ross W. Smith

Many studies have been made of the microflotation of quartz (1,2,3,4,5,6) and alumina (3,5,6, 7,8) using various anionic and cationic hetero- polar hydrocarbon surfactants as collectors. A few studies have been made on these minerals using amphoteric hydrocarbon collectors ( 9,10, 11,12) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors (13,14). The present investigation compares microflotation response of the two minerals in hydocarbon and fluorocarbon collector systems of the anionic, cationic and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1979

By Hemendra N. Kalia

The target to double the coal production by 1995 presents a formidable challenge to the coal mining industry. The mines of future, probably will be located in relatively difficult geological environment because of the exhaustion of the well defined bedded and easily minable deposits. To compound the problems of mining industry will be the reliance of power plants need for coal. The coal must reach the power plants on schedule to avoid expensive blackouts and brown¬outs. It will be imperative that the mines operate without interruptions and at designed capacities. The parameters which have been traditionally responsible for the interrup¬tions of production are: breakdown of production machinery, labor management relations and geological anomalies. Of these three problems, solutions for the first two can be arrived at by developing procedures to correct the situation. A planned maintenance and preventive maintenance program will go a long way in minimizing the equipment breakdowns. Labor relations will eventually improve as the miners begin to enjoy long-term employment. However, with the geological problems, the situation will probably continue to deteriorate and would require careful planning to minimize the impact of geological problems on production and safety. Some of the geological aspects which interfere with production are: faults, washouts, slips and slickensides, water bearing overlying strata, impuri¬ties in the coal seam, and presence of expansive clays in the coal floor. The design of large capacity mines will have to incorporate the geological distur¬bances and mine through them it may become very uneconomical to abandon producing sections because of the presence of the geological anomalies. This paper discus¬ses the geological aspects of coal mining which should receive consideration from the inception of the mining ventures. Pertinent geological aspects are discussed to develop the data base which will aid in evolving safe and efficient mine layouts.

Jan 1, 1976

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By John M. Karpinski

A method and equipment have been developed Tor measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional .to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts, The results are interpreted in terms of the flaw theory of brittle fracture.

Jan 1, 1964

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores&apos; as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By Wallace W. Key

Problems of marketing industrial minerals to chemical manufacturers are manifold. In addition to the difficulty of establishing demarcation lines between "crude" and "processed" industrial (nonmetallic) minerals, and "industrial mineral compounds" further uncertainty exists because some chemical manufacturers do not talk the same language as the industrial mineral producer. For example, paint technologists use "rutile" and "anatase" to describe highly refined chemical compounds. The earth scientists use these terms to describe naturally occurring minerals. Further, marketing research problems are intensified because of the overlapping data of the Standard Industrial Classifications (SIC) groups, and the inexactness of "Chemical Industry," "Chemical and Allied Products Industries," and "Chemical Process Industries," which are widely variable in meaning but are often used interchangeably. Bureau of Mines information Circular 8244, "Minerals for Chemical Manufacturing," was the out¬growth of an attempt to unravel some of the problems caused by overlap of statistical data compared with actual industry practices. Using this study as a base, specific industrial mineral applications of some important sub-industry groups were analyzed for the; California chemical industry. Differences between local and national practices were compared. Practices usually differed, depending on cost and availability of alternate minerals, climate, idiosyncrasies, local regulations, and other conditions. Bureau of Mines Information Circular 8260, "Mineral Fillers for the California Pesticides Industry," is the first such analysis of, a sub-industry group. Other such studies are underway. Obtaining national data is easy, but to be able to compile meaningful information which can be revealed on a regional and State basis generally is difficult and often impossible. This paper will briefly emphasize some of the industrial mineral problems encountered, and bring out the needs and benefits being derived through the continued cooperation of authoritative officials concerned with supply and consumption of industrial minerals in government and industry.

Jan 1, 1965

By C. E. Jordan

The fundamental characteristics of ultrafine chalcopyrite flotation were investigated by the Bureau of Mines to establish techniques to improve recovery of ultrafine chalcopyrite. Intense agitation during conditioning was found to improve flotation recovery of the ultrafine chalcopyrite. A split-circuit flotation design, treating the plus 38-µm-size ore by the conventional method and treating the minus 38-µm-size ore with intense agitation conditioning followed by flotation, recovered 95.6 pct of the copper in a 28.3-pct-copper concentrate, This was a 5-pct increase in copper recovery over the conventional chalcopyrite flotation method.

Jan 1, 1986

By H. R. Green

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as Significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the required actual stream velocity. It was originally planned to utilize a series of charts and nomographs for the design procedure. A nomograph, based on data given in Taggart&apos;s Handbook of Mineral Dressing (1), was developed to determine the solids transport velocity. The velocity thus determined was used with Manning charts to determine the launder slope .and configuration as though the fluid were water. It was planned to utilize a "slope adjustment factor" to increase the slope to compensate for the apparent viscosity of the slurry. All attempts to develop a suitable correction factor failed. This failure was principally due to the complex relationship of viscosity to the required slope. It was then decided to revise the entire approach. Specifically, the present procedure is based on the Darcy-Weisbach flow equation, which is rationally preferable to the Manning equation. The Camp (2) equation is used for the solids transport velocity. The necessity of reference to the Moody curves for the Darcy friction factor is avoided by using the Colebrook and White (3) equation. The resulting mathematics require iterative solutions for several of the unknowns.

Jan 1, 1978

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines&apos; program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau&apos;s continuous residue processing plant, College Park Metallurgy Research center.&apos; The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960