Search Documents

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By Wayne L. Johnson

The depth capability of engineering seismographs has been greatly increased by the use of signal enhancement, a technique in which seismic waveforms created by repeated impacts are digitized, stored, and summed. Summation amplifies the signal and partially cancels background noise. This gives a clearer picture of the wave aid makes it possible to determine the travel tune of signals from 'eater depth. Signal enhancement combined with continuous display of waveform, permanent recording of waveform, and precision digital readout of travel time has opened new fields of application in mining and engineering. Recent work has clown that replacement sulfides can be distinguished seismically from country rock at Bistee, Ariz. Work on the Iron Range of Minnesota indication,: that, by using a 300 pound weight as the source, the Biwabik iron Formation can be traced down dip to several hundreds of feet traverses over known areas show that reflections can sometimes be identified. Reflection, if identified preclsely, give a mere accurate estimate of depth and buried topography. Comparison of ( ) and weight drop have given some understanding of low wave amplitude varies win; source candid

Jan 1, 1971

By James Wm. White

Computer-based mine management systems are being used in many surface mines to assign haul trucks, track equipment and manage information. Advances in digital communications allow these systems to be used in underground operations. Underground mine management systems help maximize production by providing gains in equipment and manpower use, drawpoint equalization in block caving operations, preventive maintenance and safety. Current systems use allocated or "locked" train and load-haul-dump (LHD) dispatching. Allocated dispatching rarely optimizes open pit product' on. But it offers an efficient mode of operation underground and where options are more limited. The primary objectives of underground mine management systems are to maximize production and mini¬mize contention time through allocated train, truck or LHD dispatching, traffic control, equipment monitoring and comprehensive reporting. The main components of an underground mine management system include: ? A central computer (personal computer or worksta¬tion) in a central control center. It sends instructions to train, truck or LHD drivers and allows dispatcher interaction. ? A field computer system (FCS). This consists of a touch-screen graphics console (GC) and mobile hub - on each train, truck or LHD to receive and display instructions from the central computer and accept driver input. ? A data radio network based on leaky feeder (data, voice, video) or microcell radios (data only) and advanced token-ring technology. This passes information between the central computer and the FCSs. ? Radio frequency (RF) tags mounted at boxes, weigh bridges, tips and rim tunnel main haulage ways to locate trains or LHDs (Luke, 1993). Such a management system must be in place before implementing computer-based dispatching (Vagenas, 1991) for production optimization.

Jan 1, 1997

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By P. A. C. De Ruiter

The Lower Cretaceous salt deposits of the Gabon Basin and Congo Basin were said down on ton of an Burly Cretaceous Lato Jurassic, continental graben fill that represent!) the rifting phase of the Afro-American continent. The salt 13 characterized by high percentages of potash and magnesium salts and the scarcity of sulphates and carbonates. The salt probably originated from a brine that was already enriched in high-soluble salts before entering the Gabon Congo basins. Their low-solubility equivalents are found in the Cuanza Basin of Angola. Commercial mining of the potash salt is only possible in those onshore areas where it is essentially undisturbed, shallow and of the right chemical composition. These conditions are net in Congo where the Holle mine produces from rich sylvinite deposits.

Jan 1, 1978

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By Robert J. Wright

The purpose of this paper is to propose a classification of uranium deposits that is believed to be well suited to the needs of uranium exploration and resource assessment. By way of background some observations are offered about mineral exploration in general, and uranium in particular. Attention is first given to the we of models in mineral exploration. Some general principles of mineral deposit classification, the basis for model formulation, are then considered. Finally, the uranium classification is presented.

Jan 1, 1979

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler's comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body's actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore's geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968