Search Documents

By J. W. Hawkins

Understanding aquifer properties in surface mine backfill is essential for managing the groundwater flow system as well as controlling the formation and discharge of acid urine drainage. Slug tests (injection and withdrawal) performed on wells in mine spoil may yield two distinctly different response characteristics. One type of response is indicative of a porous media system. The second type of response indicates the presence of a pseudokarst system. The presence of voids or conduits in the backfill is indicated by an almost instantaneous partial recovery of the water level displacement. This rapid recovery is turbulent flow and cannot be analyzed by conventional (Darcian) methods. The turbulent flow may cause the calculated hydraulic conductivity to be less than the actual values. The slug dissipation surface area created by the voids contiguous to the test well add to the known dissipation surface area of the screened interval. This can cause the calculated hydraulic conductivity to be greater than the actual hydraulic conductivity or the aquifer to appear more permeable. Whenever analyzing data from aquifer tests in mine spoil, these potential problems must be kept in mind. In spite of the problems encountered during slug testing of spoil, the aquifer hydraulic parameters derived and the slug responses observed remain useful in the hydrologic characterization of a mine site.

Jan 1, 1994

By A. Papandreou

Industrial wastes nowadays constitute one of the most serious threats for the future of our planet. Researchers around the world have very often proposed many kind of solutions in the management problem of industrial effluents. However in most cases suggested solutions are either too expensive to be applied in industrial scale, or they just transfer the problem (e.g. precipitation creates dangerous sludge) and so they create an even greater problem and threat. In the present study the exploitation of valuable hydraulic and adsorption properties of fly ash is studied. Fly ash can easily and cheaply be shaped into stable pellets. After ageing for a sort period of time, these structures can be used as adsorbents for the removal of heavy metals from industrial effluents. Experiments in aqueous solutions have shown excellent adsorption behavior concerning the removal of cadmium, copper, lead, chromium (III) and zinc. The advantage of this technology, except low cost, is that after saturation the pellets can be easily removed from the liquid phase and stabilized in concrete structures without any problem of desorption or leaching. Moreover in these structures a significant amount of cement in the concrete can be replaced by raw fly ash. (Ashcrete as it is called). The utilization of an industrial byproduct as fly ash in the form of pellets as adsorption means and their stabilization with concrete (or ashcrete) combines the useful properties of a solid waste in the treatment of liquid effluents and constitutes a green low cost technology.

Jan 1, 2006

By Duane Jorgensen

Two types of factors direct the search for gypsum deposits-geologic factors and economic factors. The prime control and major economic factor is the market for the possible products. The major geologic factor is the control of the depositional environment, which determines whether or not a deposit exists within a given market area. After discovery of a deposit, the distinction between economic and geologic factors is not as clear as before, and the geologic characteristics of the deposit become the economic factors in evaluating the deposit for production and processing. The geologic characteristics are concerned with 1) the gypsum rock, 2) the host or country rock, and 3) geologic fluids, such as gas and water. Prospecting includes both original discovery and the continuing information-gathering period. During this time the above three characteristics of the deposit are determined, usually from core drilling, from phenomena observed during drilling, and from the core and hole. Important information and means of gathering it include sample analyses, sample volume, impurities and their distribution, water levels, aquifer tests, permeability measurements, rock strength tests, rock and overburden thicknesses, rock types, and direct observations of water and gas. Data gathered or inferred from all of these determine the mining or quarrying geometry and environment: which in turn determine the equipment, development, production, and processing costs. Impurities in gypsum deposits are very important in manufacturing processes. The impurities and their effects vary widely from inert minerals with little effect to reactive minerals with strong and mostly detrimental effects.

Jan 1, 1978

By Robert S. Saunders

Cast iron tubbing for two centuries was the only practical watertight shaft lining for deep waterbearing formations. However, since World War II composite welded steel and concrete lining has gained favor and today is often preferred. While tubbing may not be applicable in all cases, a good argument can still be made for this time-honored method. Watertight linings are complex structures designed to withstand both hydrostatic fluid pressure, non-uniform loading created by ground forces, and vertical bending caused by subsidence. Resulting stresses in the lining can be high. To date linings have been designed that withstand hydrostatic pressures as high as 1,500 psi. Watertight linings must be robust, constructed of the highest quality materials, and manufactured and installed with precision. Therefore, such linings are expensive. Today's ductile cast iron tubbing is greatly superior to gray iron formerly used for tubbing, and is stronger, and more resistant to corrosion than welded steel lining. Tubbing, unlike steel linings, can be installed in wet conditions and used to control water inflow and stabilize unconsolidated ground as the shaft is deepened. Steel lining requires absolutely dry conditions for welding, which often necessitates expensive ground freezing and a primary lining.

Jan 1, 1985

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By R. Venugopal, T. C. Rao, M. Vanangamudi

Introduction The kinetic approach, to understand a process in detail, has been extensively used in the unit operations of many engineering systems. In green pelletization, the kinetic studies have been mainly oriented towards quantifying the growth mechanism (Kapur and Fuerstenau, 1964; Sastry and Fuerstenau, 1977; Capes and Danckwerts, 1965; Kapur and Fuerstenau, 1966; Kapur, 1972) and in a few cases, relating the rate of growth with added liquid content (Kapur and Fuerstenau, 1964; Newitt and Conway-Jones, 1958). Studies on the kinetics of green pelletization, in terms of the order of the kinetics are virtually non-existent. Sastry and Fuerstenau (1970) classified the agglomeration process into "free in-space" (dilute particle system) and "restricted-in¬space" (highly dispersed particle system) and noted that the former is a second-order process while the latter corresponds to a pseudo first-order rate process. The present paper attempts to describe the kinetics of green pelletization, in terms of order of the kinetics, using pyritiferrous shale as the material system. Experimental Pelletization experiments were carried out using -100 mesh pyritiferrous shale, in a laboratory disc pelletizer, at four intervals of pelletization time (15, 20, 25 and 30 min). The green pellets obtained were size analyzed. The size distribution of pellets has generally been represented by a single parameter such as the mean granule diameter, ratio of maximum and minimum pellet diameter, etc. In the present study, the d50 (50% passing size) of pellets has been considered to represent the size distribution of pellet. Kinetic equations The process of size enlargement is considered analogous to chemical reaction and a general kinetic equation of nth order for growth of pellets is given as

Jan 1, 1990

By Thomas H. Koenning, William E. Bruce

The importance and complexity of the ventilation systems in many underground coal mines necessitates the use of digital computers to model the ventilation networks. The modeling procedures used by the Mine Safety and Health Administration (MSHA) utilize the MSHA-modified Penn State computer program. The basic techniques used by MSHA have been described in detail in NESA (now MSHA) Informational Reports 1066 and 1183 (1. 2). Two basic methods are utilized for modeling underground mine ventilation systems. The first modeling method is the use of actual air-flow, pressure, and fan-performance data acquired during a full air-pressure, air-quantity ventilation survey to develop a mathematical model of the ventilation system. The second modeling method is the design of a ventilation system using data obtained from calculation, from past experience, or from technical literature. The latter method would typically be used to design a ventilation network prior to developing a new mine. Regardless of which method is used for modeling, there is a need to know, or to calculate, appropriate resistance values to be used for airways and for the various ventilation control structures. Such data is typically difficult to obtain and this report is an attempt to summarize typical resistance values which may be used in designing ventilation networks for new mines or in simulating proposed system changes in existing mines. Illustrations are presented to show where some of the resistances typically are located and how they are modeled in mine ventilation net- works.

Jan 1, 1987

By John Wilson

HARRY HINDS: Our first speaker today is Dr. John Wilson. Dr. Wilson is chair and Union Pacific/Rocky Mountain Energy Professor in mining engineering at the University of Missouri-Rolla. He has previously held senior management positions with Trans- African Mining Ltd., Anglo American Corporation, Consolidation Coal Company, Smith International Inc., Adams Resources Inc., and Golder Associates. John started his mining career as a coal miner in the coal fields of northern England. Dr. Wilson received his bachelor of science degree from the University of Durham, his master's degree from the University of Newcastle Upon Tyne, and his doctorate from the University of Witwatersrand, all in mining engineering. Today, Dr. Wilson is going to address the subject "Hiring Recent College Graduates Versus Hiring Experienced Mining Engineers." Please welcome Dr. Wilson. DR. JOHN WILSON: The advantages and disadvantages of hiring engineers directly out of school or those with some experience are often discussed among mining company managers. The choice is essentially dependent on the culture of each company, the company's maturity and strategic direction, and the growth or phaseout plans in vogue at the time of the decision. Generally, major, established mining companies employ entry-level college graduates and train them, introduce them to company culture, include them in a succession plan to replace retirees, fill vacancies, and provide management to direct future growth of the company. However, some large companies take a different approach. During restructuring, down-sizing, etc., some companies do not hire college graduates directly from school. Rather, they tend to recruit from other companies or absorb valuable personnel available following acquisitions or mergers. While this is a logical approach, it seldom provides for the future management and leadership needs of the company. A clear example of this failure is found when reviewing the hiring practices, or lack thereof, in the coal industry of the 1950s.

Jan 1, 1998

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

By Carl Barchet

INTRODUCTION Located on the Colorado River on the Nevada-Arizona border about 56 km (35 miles) southeast of Las Vegas, Nevada, Hoover Dam is a gravity arch dam 221 m (726') high for electric power generation and water supply. The head waters of the dam form a large reservoir, Lake Mead. The dam is equipped with two emergency spillways, one in the Nevada abutment and one in the Arizona abutment. Both spillways which are concrete lined and 15.25 m (50') in diameter, were intended for use only if Lake Mead is full and incoming flow of the Colorado River exceeds the discharge capacity of the turbines and regular bypass conduits. In the spring of 1984, a combination of rain and unusually rapid snow melt required the opening of the spillways for only the second time in the 50 year history of the dam. As in the previous use in 1942, the massive discharge of water through the tunnels resulted in severe damage to the concrete Linings of both tunnels. This damage is the result of cavitation which occurs as the discharge water flows at very high velocities over minor irregularities in the concrete lining. The U.S. Bureau of Reclamation has long been aware of the cavitation effect which occurs during these high volume discharges and has been studying solutions. One solution to the problem is to induce air bubbles into the flowing water to eliminate the vacuum associated with cavitation. This solution had been implemented at Yellowtail, Flaming Gorge, Blue Mesa, and Glen Canyon dams by constructing an aeration slot in the inclined portion of their spillway tunnels. Since the spillways of Hoover Dam were already in need of repair, the BUREC decided to construct similar facilities in each of the two 15.25 m (50') diameter spillways coincidental with the other repairs required.

Jan 1, 1987

By Donald Ross-Watt

Mining project investment concerns the installation of mine capacity for the purpose of generating a stream of future economic benefits. In order to make this type of investment decision, the optimum specifications for the project must first be determined. Then, the economic justification of the investment tin be evaluated based on these specifications. Economic evaluation to guide mining project investment decisions is based on a proposed plan for mining the deposit over its operational life. If single point estimates are made of deposit characteristics and environmental parameters* as the basis for assessing a future stream of economic benefits associated with the investment, a future mining-plan can be optimally fitted to these estimates and, to the extent that such estimates are actually realized, this plan will retain optimality.

Jan 1, 1979

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are. the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread- sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin.

Jan 1, 1987

By Gail B. Knight

INTRODUCTION In May 1984, The Canadian Pacific Railway awarded to the Joint Venture of Foundation of Canada, Ltd. of Toronto, Atlas Construction Co. of Montreal, and S. A. Healy Co. of Chicago the contract for the construction of 27,000 ft of tunnel starting from the east portal. Selkirk contractors, the Joint Venture of Foundation, Atlas and Healy, which had successfully completed for CPR in 1983 the construction of both portal structures for this tunnel, studied several different alternative proposals before presenting its bid pooling each individual company's technical resources and experiences. (Foundation had just completed in association with other companies a similar tunnel project in British Columbia, and the S. A. Healy Co. could provide its experience of more than 40 miles of tunnels excavated by full face boring machines.) Among the alternatives investigated there was a fully circular tunnel to be excavated by a 30 ft diameter TBM, a full section drill and shoot proposal, and a mixed alternative, the "key hole" proposal, consisting of a TBM driven circular top heading followed by benching to design size. Technical, geological and economical considerations determined the alternative that was eventually proposed to CPR. HISTORICAL NOTES The tunnel construction parallels an existing tunnel through the Selkirk mountains that was excavated in 1885. In order to reduce the grade to 1% on the heavily loaded west bound trains, the new tunnel was at a lower elevation and lengthened to almost 9 miles. GEOTECHNICAL INFORMATION CP Rail site investigations began in 1978. The surface rocks in the tunnel construction area are metamorphosed Cambrian and Pre-Cambrian sediments; the underlying formation contains fine and coarse grained rocks presenting different degrees of metamorphism. The

Jan 1, 1987

By Richard M. Michaels

In considering the use of underground space for civil works functions, there are several criteria that must be met if transfer of any of them is to occur. It is important to recognize that these criteria involve social and political as well as conventional engineering and economic considerations. It is the purpose of this report to identify certain of these criteria and develop a set of measures that will permit the evaluation of the potential benefit of transferring civil works functions underground. The work reported here was completed for the ASCE and is contained in the report, Undergound Space, 1973. If one examines the total direct and indirect economic return from the location of civil works in subsurface rather than surface space, sizeable benefits accrue. This occurs largely because design, construction, operating and maintenance costs of these systems are highly dependent upon the forces exerted on these systems by the surface enviroment itself. Transferring of these facilities to underground space would eliminate a large segment of those costs. It is equally true that civil works functions compete with other uses for surface space and generate significant conflicts with these competing uses. Highway construction takes land from other productive uses. Electrical transmission lines conflict in terms of safety and aesthetics with adjacent social activities. Assuming that construction costs can be made equivalent, the analyses in the previous report indicate that the locating of all civil works functions underground would yield an annual net savings to the society of the order of 60 billion dollars. It may be added that the benefits in terms of improved social perfromance would also be substantial. However, it is clear that the benefits from utilization of subsurface

Jan 1, 1974

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By P. J. Macbeth, R. F. Overmyer, K. K. Nielson

INTRODUCTION Over the past several years, Ford, Bacon & Davis Utah Inc. (FB&DU) has been involved in research, development, and engineering activities concerning uranium mill tailings; specifically of interest in this paper are efforts in radon gas exhalation and surface flux attenuation measurements, environmental influences on radon fluxes, and basic research into radon gas behavior. Our projects have included measurements of effectiveness of specific cover material in attenuating radon surface fluxes from mill tailings, characterization of the parameters in cover materials and tailings that influence radon exhalation, long-term tailings stabilization planning, determination of the effects of moisture on radon emanation and diffusion from ores, and determinations of baseline radon fluxes. Our efforts have been sponsored by U.S. Department of Energy, the U.S. Nuclear Regulatory Commission, Tennessee Valley Authority, the commercial uranium industry, and we are presently engaged in efforts for the U.S. Bureau of Mines. Much of the material presented in this paper is taken from our published reports on radon flux attenuation and tailings stabilization (Macbeth et al., 1978; Nielson et al., 1980; Rogers et_ al., 1980; Thamer et al al., 1980). CHARACTERIZATION OF RADON GAS EXHALATION One dimensional diffusion theory based on Fick's laws is the basis for the modeling of radon gas migration through large quantities of porous tailings and cover materials applied over the large areas of tailings piles. Fick's first law relates the gaseous concentration gradients to the flux over the entire surface and defines the effective diffusion coefficient De as: [ ]

Jan 1, 1980

By George E. Aiken, B. R. Jr. Waples

INTRODUCTION In this paper the author will attempt to bridge from the paper work of design and engineering to the reality of implementation. Certain facets of construction are constant to a successful project, no matter the level of technical complexity. Basic to timely, low cost construction are the people assigned to the project. Construction is not accomplished by robots, computers, or speeches; but rather by people. People do however require the avail- ability of equipment and communications to properly complete the work. ORGANIZATION Good organization is the basic requirement of a well implemented construction project. For this paper the author will suggest an organization chart as well as an activity listing that together support the construction activities. There is little difference in the activities or functions needed to construct a small plant or a large one. It is a matter of how much time an individual has to spend on an activity that determines the structure of an organization. The difference between a large and small plant construction job is often described as the multiple hat versus the single hat philosophy. As an example, a resident construction manager on a small job might be the manager, the field engineer, the scheduler, the estimator, and the procurement manager. At some time during a construction

Jan 1, 1986