Search Documents

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

Geopolymerization is a process by which Al-Si minerals undergo dissolution and polymerization in an alkaline solution to form a monolithic material with a high mechanical strength (Davidovits, 1991; 1994). In this study, Na-feldspar (albite) and K-feldspar (microcline) have been selected to investigate their abilities to undergo geopolymerization. The interaction between alkali metals present in the alkali-feldspars and alkali metal cations contained in alkaline solution during geopolymerization has also been studied. It has been found that both albite and microcline can be applied in geopolymerization to produce geopolymers with a high compressive strength. Although the dissolution of M-feldspar (where M = Na and/or K) in concentrated MOH solution is inhibited when the alkali metal cations of the alkaline solution differ from the alkali metals structured in M-feldspar, the resulting geopolymers are found to demonstrate a higher compressive strength. Moreover, a proper molar ratio of Si/Al in the geopolymeric gel phase and a higher average hardness of the undissolved particles remaining in the geopolymers are found to greatly increase the ultimate compressive strength of the geopolymers.

Jan 1, 2002

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997