Search Documents

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By H. L. Barwood

Luminescence excited by electron bombardment, or cathodoluminescence (CL), is a very useful tool in petrographic examination of rocks, minerals and ores. Differences in luminescence colors and intensities allow detection and delineation of mineral species and composition zones difficult to separate visually by normal polarized light microscopy. The cold cathode CL chamber at Indiana University is used with a binocular microscope that has interchangeable attachments for a normal film camera, a digital camera and a fiber optic spectrometer. This allows imaging of the specimens as well as limited spectrographic analysis of the emitted luminescence. The chamber on this CL unit is large enough to accommodate several thin sections, polished mounts, grain mounts or rock slices at one time. Luminescence petrographic techniques were used to study alkali syenites and carbonatites from the Arkansas. Alkali feldspars in the syenites reveal a history of growth, fenitization and replacement through color and intensity differences. Primary orthoclase luminesces bright blue and is often zoned with a duller blue overgrowth of microcline. Fenitization of the feldspars is demonstrated by dull to bright red luminescence and replacement veins of albite often have a bright yellow green luminescence. Late microcline and perthites from the syenite pegmatites have a dull yellow to orange luminescence. Easily visible on this background of feldspars are grains of apatite (yellow), fluorite (violet), zircon (greenish), sodalite (orange) and mosandrite (green). Complex pseudoleucite syenites from Magnet Cove, Arkansas show similar minerals but also include xenolithic quartz (violet), manganwollastonite (bright orange), benitoite (intense blue) and lorenzenite (green). Carbonatites from Arkansas contain a wide variety of calcite textures and intensities of luminescence. Grains of carbonatite in well cuttings are easily distinguished from sedimentary calcites by their complex “flame” luminescence and the frequent presence of euhedral apatite grains (yellow). Apatite crystals separated from the Arkansas River Valley carbonatites by acid digestion show complex zoning. The cores of these apatites are yellow luminescing due to CL activation by Mn enrichment while the rims are violet luminescing due to REE enrichment. Complex zonation between the cores and rims is easily visible using CL.

Jan 1, 2001

Recent advances in GPS, machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50mm (2 inches).Some of the outcomes possible are: precise selective mining – even when the ore is visually indistinguishable from waste: tracking grade and tonnage of every ore parcel through the mine: real time productivity monitoring: detailed post accident safety analysis: tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2004

By Sohta Takatsu, Hachiroh Mizubata, Shigeki Kudoh, Kazuya Takekuni, Yoshinori Yamada

A special type of shotcrete is used to improve the performance of open-type TBM in difficult situations. The Hakamagoshi and Johana tunnels are expressway evacuation tunnels of 3.2 km and 5.1 km in length, respectively (total 9.1 km) that were excavated by one open-type TBM. The geological conditions at the sites were estimated to be good before excavation. However, 95% of the rock turned out to be two ranking orders worse than the estimated classes. Therefore, we used a special shotcrete for bad rock conditions, and succeeded in excavating the tunnel at an average rate of 270 m/month.

Jan 1, 2001

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Axel Nitschke, Josef Arnold

Bochum’s Underground Lot 306 was characterised by a confined site and unique tunnelling methods. A highly mechanized construction concept was developed to achieve high progress rates. Bespoke backup systems for muck disposal and material supply were used. For the first time in suburban tunnelling, wet shotcrete, batched onsite, was applied. A three-storey underground car park had to be undermined with only1.5 m of overburden and had to be lifted several times by “compensation grout in.” An existing operational two-lane metro tunnel was enlarged without any major impact on train operation.

Jan 1, 2005

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160ºC and 1,380 kPa (200 psi) oxygen overpressure, DEW to produce LME Grade A cathode, recycling of the lean electrolyte to the pressure leaching step and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of the lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an ?acid-autogenous? process referred to as the ?MT-DEW-SX? process. This paper (Part III) discusses the steps taken to develop and complete a large-scale demonstration of the process at Bagdad, Arizona, in 2005.

Jan 1, 2007

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999