Search Documents

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

Jan 1, 1997

By Michael E. Allen

The building of sanitary and storm drainage sewers in urban or environmentally sensitive areas often requires the use of tunnel construction procedures. While hydraulic considerations may require only small diameters, traditional tunneling techniques make small sizes the least economical. Current state-of-the-art techniques using highly mechanized systems of pipe jacking can provide cost effective solutions to the problems of construction of small size tunnels. The characteristics of mechanized pipe jacking allow rapid advances under difficult ground conditions. The basic pipe jacking cycle is used with a variety of excavation systems to permit the contractor to satisfy engineering as well as economic parameters. These characteristics and several of the systems available are outlined.

Jan 1, 1981

By Dominic F. Howarth

Groove deepening (deepening of a groove in rock by successive passes of a rock cutting tool) is a potential operational feature associated with tunnel boring machines. Little research has been undertaken in this area which is of direct practical relevance to the design and application of tunnel boring machines. Laboratory experiments using single, double and triple disc arrays have revealed an important fundamental cycle of events associated with disc cutters when progressively deepening a groove. Furthermore, in contrast to pick cutters, groove deepening by discs is shown to be an efficient operation. This can be directly attributed to the increased interaction between disc cutters due to the increase in magnitude of lateral forces generated as a groove is deepened.

Jan 1, 1981

By Patricia T. Foley

An analysis of the demand for copper shows a widely varying pattern of end use. For example, copper tube is the most popular material for hot water supply in the US and northern Europe, but galvanized steel is used in Japan and plastics are used in developing countries. In addition to such peculiarities of end use, the demand for copper varies among countries depending on the stage of industrialization and the extent that the copper processing industries are developed. Brazil, with its abundant supplies of bauxite and hydroelectric power, uses aluminun in place of copper wherever possible. South Korea, with its export oriented economy and its advanced custom smelting and fabricating industries, favors copper. Understanding the details of demand in different countries enhances statistical derived forecasts and illustrates potential new markets.

Jan 1, 1986

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By McDonald E. Wrenn, Narayani P. Singh, Victor E. Archer, Ceno Saccomanno

Fourteen uranium miners' lungs from Colorado plateau were collected at autopsy and the concentrations of 238U, 234U and 230Th were determined by radiochemical procedures utilizing solvent extraction - alpha spectrometric techniques. The uranium and thorium isotopes are in near equilibrium with average concentrations of 238U, 234U and 230Th being 89.3, 95.2 and 91.1 pCi/kg respectively. The combined average radiation dose rate to lung from these three isotopes is about 24.2 mrad/year at death excluding the unmeasured contribution from the 226Ra and daughters. The average concentration of 230Th is about 65 times higher than the mean concentration of 230Th in lungs of non-miners dying at comparable ages from the same region.

Jan 1, 1981

By S. Barkhoudarian, R. R. Gupta, R. F. Steinberg

A study of the feasibility of using acoustic signals to detect discontinuities ahead of excavation has shown that reflecting interfaces in a homogeneous rock can be easily identified. Moreover, discontinuity interfaces in a very complex field site (where the rock face was weathered, was full of jointed rocks, and had a destressed zone running along the mine walls) could be identified with a reasonable level of confidence, using a cross-correlation technique for signal processing. The results of this study go a long way toward proving the feasibility of the technique. However, further development work is needed to optimize an operating system in a hard rock environment where boring machines are used for excavation.

Jan 1, 1997

By V. Saltas

In the present work, dielectric spectroscopy experiments were conducted on bentonite samples collected from Milos Island, in order to study their electrokinetic behavior in correlation with water content and mild heat treatment. Low-frequency dielectric spectroscopy has proved to be a power tool in the study of the electrical behavior of clay-water systems, because polarization and relaxation processes typically affect response at frequencies below 100 kHz. Therefore, dielectric and conductivity measurements in the frequency range of 10mHz to 1MHz were carried out by means of a high-resolution broadband spectrometer on bentonite samples, at various levels of hydration. The evolution of dielectric response was also examined after annealing of the samples. Experimental data were computer fitted with the empirical Havrilliak?Negami dielectric relaxation function on which a conductivity term was superimposed. The evaluated parameters of the fitting function are shown to be strongly affected by the water content of the measured samples.

Jan 1, 2006

By K. N. Han

The dissolution kinetics of cobalt in iodine/ iodide solutions were investigated using a rotating-disc technique. Variables studied included temperature, rotating speed, concentration of lixiviants and the pH of the solution. The overall dissolution reaction appeared to be limited by the mass transfer of tri-iodide through the diffusion boundary layer with an Arrhenius activation energy of <16.2 kJ/mol (4 kcal/mol) over the temperature range of 2 to 42ºC. The pH of the solution had little effect, as long as the pH of the solution was <8. However, when the pH of the solution became >8, the dissolution rate decreased dramatically, due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1995

By R. W. Smith, S. A. Davis, A. M. Raichur, M. Misra

The flocculation of coal is typically accomplished by the addition of commercially available polymeric flocculants. Recently it was shown that biopolymers derived from microorganisms can also be used. The biopolymers flocculate coal efficiently and make the coal more hydrophobic. This increase in hydrophobicity can be utilized to separate coal flocs and can be used for reducing the moisture content of the flocculated coal. In this regard, flocculation and settling tests using biopolymers and synthetic flocculants were performed on fine coal. The experimental results are discussed and a transport model is presented for the time-dependent settling of fine coal.

Jan 1, 1998

By Wojciech Klecan, John H. Raymer

Baseline quantities of difficult ground and support types were estimated for the Chattahoochee Tunnel using the Rock Mass Rating system. RMR classifies the ground into five categories, ranging from “very good” to “very poor,” based on five main parameters: intact rock strength, RQD, joint spacing, joint condition, and groundwater inflow. For the Chattahoochee Tunnel, these parameters were independently measured in the cores and shown graphically on the boring logs. A 55 matrix was calculated to obtain the statistical distribution of RMR for the project. Three baseline ground types were defined based on the RMR. Geologic mapping inside the tunnel during construction has verified the accuracy of this method.

Jan 1, 2003

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By G. Blackwell, E. Bozorgebrahimi

The trend in open pit mining has been to maintain cost competitiveness through economies of scale, particularly by implementing larger trucks and shovels. This paper considers the potential adverse impact of such scale adjustment, however, on dilution, maintenance, flexibility, and other aspects of operations. It examines the mine production characteristics affected by increased equipment size and attempts to quantify the impact on the overall operation. Reference is made to data from operations that have experienced a variety of equipment size ranges changes over the last decade.

Jan 1, 2003

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By William B. Thayer, James H. Meinholz

The Milwaukee Metropolitan Sewerage District (MMSD) has been working since mid-1977 on a fast track to meet a court-imposed schedule to rehabilitate a large wastewater collection and treatment system at an estimated cost of $1.7 billion. Because of glaciation, the Milwaukee area has an extremely complex geologic environment. The rock surface ranges from outcroppings in the northern and western parts of the area to 76 m (250 ft) below the surface at the mouth of the Milwaukee and Menomonee Rivers. Bedrock beneath the glacial mantle is a thick sequence of early to middle Paleozoic sedimentary rock. To cope with the many complexities of this large public works project, a Program Management Office (PMO) concept has been employed. A Geotechnical Engineering Group was established within the PMO to provide a continuous , unified approach to geotechnical engineering and full disclosure of all geotechnical information in the construction contract documents. It provides qeotechnical engineering to design and construction, develops and maintains a qeotechnical data base, and participates on the claims resource team.

Jan 1, 1983

By Michael R. Smith

Barrick Goldstrike Mines Inc.’s Betze open pit is located at the north end of the Carlin Trend, in Eureka County, NV. Ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County (Fig. 1). The final pit will be about 2440 m long x 1550 m wide (8000 x 5100 ft), elongate in a west-northwesterly direction and about 425 m (1400 ft) deep. The pit straddles the Barrick-Newmont Gold Co. property boundary. History The first hole at the Goldstrike Mine was drilled in 1962. Between 1963 and 1964, 17 shallow holes were drilled with little encouragement, in view of the price of gold at $1.12/g ($35/oz). From 1962 to 1975, several different companies explored the Goldstrike property. In 1975, Pancana Industries acquired the property. In 1976, Pancana’s exploration efforts found sufficient gold mineralization to initiate heap leach production. In 1977, Pancana formed a joint

Jan 1, 1994

By James P. Dorian

Like Russia and Ukraine, Kazakhstan is one of a few former Soviet republics well-endowed in mineral and energy resources (Fig. 1). Kazakhstan is the second largest newly independent Commonwealth state. It possesses major fuel and power centers, including 20 electric power facilities that operate on the more than 300 kt (330,000 st) of coal extracted daily. These power stations supply Central Asia, the Urals and Western Siberia with much needed electricity. Kazakhstan plays a critical role in Central Asia as it serves as both the regions&apos; economic and political hubs. While Kazakhstan already contains a robust and diversified minerals industry, the government is actively pursuing foreign investment to boost production capacity and improve efficiencies in operations. A primary objective of the Kazak government is the expansion of metal processing facilities to improve the country&apos;s long-term export potential. Since 1991, international mining companies have found the investment climate of Kazakhstan relatively favorable. This is due to tremendous efforts by government officials to create sufficient investment legislation and a national minerals policy, while eliminating bureaucratic bottlenecks common to most other former Soviet republics.

Jan 1, 1993

By T. Motzer

Sustainability management and reporting plays an important role in controlling and communicating a company&apos;s efforts in sustainable development. A variety of standards comprising a multitude of indicators often require similar information but with different data quality, level of detail and coverage. This may lead to inconsistencies in external communication because of the difficulties in collection and aggregation of data from different company sites and organisational levels. Using a central database system accessible via internet makes the process of data management more efficient: All relevant information can be collected on-site, with a defined data quality, credibility and consistency. Any type of sustainability indicator can be calculated automatically, once the data is collected. Individual analyses and predefined reports, e.g. GRI G3, can be easily generated and immediately published, making your sustainability communication transparent and reliable.

Jan 1, 2007