Search Documents

In April 2012, work started on one of the most ambitious construction projects of Austria?s ÖBB-Infrastruktur AG ? the New Semmering Base Tunnel. Scheduled for completion in 2024, the 27.3 km (17 mile) tunnel through the Semmering range will cut the journey time on the south railway connecting Lower Austria and Styria. Before con-struction can begin at the entrance portal and tunnel bores, the work concentrates on the above ground sections with the clearance and excavation of the entrance ramp site. The slope is currently being excavated by the Baubeteiligungsge-sellschaft m.b.H. BBG-GRAZ. The cut face is shored up with shotcrete and permanent self-drilling anchors produced by Minova MAI, an economical bolting solution for softer rock formations. After completing the surface construction work, the twin-bore, single-track tunnel will be cut through the Semmering by conventional and continuous excavation beginning in 2015. Once completed, the New Semmering Base Tunnel will be one of the longest rail tunnels in Austria. It will act as a vital link on the route crossing Europe?s heartland from Northern Germany to Italy, which currently has to climb the steep Semmering pass between Gloggnitz and Mürzzuschlag on a historic mountain railway recognized as one of the UNESCO World Heritage sites. The old route imposes considerable limitations on heavy freight trans-port, and passenger trains have to slow down to a speed of around 50 kph (31 mph). The New Semmering Base Tunnel will bypass this bottleneck and cut 30 minutes off the journey time between Vienna and Graz. It represents a particular advantage for freight traffic, since the new route?s minimal incline of 8.4 percent removes all obstacles for even heavy freight trains.

Jan 1, 2013

By Pieter Barendsen

INTRODUCTION One of the main problems in tunneling without the use of explosives lies in the development of tools which, at an economically acceptable level, are capable of continuous breakage of the rock, resulting in a fragmentation suitable for a smooth, uninterrupted transportation of the muck away from the tunnel face. Tools employed on tunneling machines have, so far, always been of the mechanical kind which break up the rock by a crushing and shearing action. Other methods of rock breaking are possible but, even if some of them have reached the laboratory testing stage, nearly all of them are still too "exotic" to be of any practical use in the immediate future. One must admit, however, that some highly interesting results are beginning to be reported from the USA on the use of high pressure water jets for the destruction of rock through erosion, a field pioneered in Europe(USSR and Great Britain). Mechanical breakage of the rock is effected by inducing stresses exceeding its compressive/shear strength, by loading it with a wedge of cone shaped tool, until cracks are formed and chips loosened. In order to allow the tools to act upon the rock face continuously, they are commonly shaped as rotating bodies, "roller bits" or "disc cutters", spinning freely and mounted on a revolving boring head of tunnel diameter. The thrust of the tools against the face is generally exerted in a direction which is parallel to the tunnel axis.

Jan 1, 1997

In 1990, US mine production of barite increased 54.1 %. Barite consumption, sold or used by grinding plants, increased by 27.6%. Imports were about the same as 1989. World mine production in¬creased 12.3%, according to the US Bureau of Mines. The value of domestically produced barite, fob mine, decreased 12.7%, according to the Bureau. The declared value, cif US port, of all imported crude barite during the year 1990 increased from $40.27/t ($36.54 per st) in 1989 to $40.61/t ($36.84 per st). Nevada continued to be the leading producer of barite with 82% of the total, followed by Georgia and Missouri. It is estimated that 750/c, of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This includes barium chemicals and fillers in paper, plastics, and glass. Tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1990. The average number of rotary rigs operating, (1010), was 16.2% more than the 1989 average of 869 in the US.

Jan 1, 1991

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there .is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages.

Jan 1, 1981

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By E. G. Kelly

Because of the nature of the breakage in the Barmac vertical spindle impactor, the 80% reduction ratio is very small, so that when the energy efficiency is calculated by Bond's method, it appears to be very low. However, the product size distribution contains a high proportion of fines. It is argued that the production of these fines accounts for the high energy consumption, and Bond's method is modified to account for this, by considering the crusher to be, effectively, a number of smaller crushers in parallel, each having a different reduction ratio.

Jan 1, 1988

By E. Fahrenkrog

An intelligent supervisor developed using expert system tools and applied to a crushing plant is presented in this paper. The structure of this supervisor, based on a model of a human operator, consists of a Knowledge base containing a qualitative model of the process, and a Rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of systems to supervise the automatic operation of a plant.

Jan 1, 1989

By A. E. Isaacson

The Bureau of Mines is studying the effect of supercritical water, at 4000 C and 3,500 psi and subcritical water at lower temperatures and pressures. on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By F. W. Pereira

The Montana Talc ore body was discovered in the summer of 1983, in the Gravelly Range, approximately 25 miles south of Ennis, Montana. Initial drilling indicated a plus-million-ton ore body of high-purity talc. Preliminary analyses were performed on the ore cuttings, .including chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. The results indicated the talc was similar to that currently being marketed from Montana and probably would have good commercial value.

Jan 1, 1989

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By Carrie Smith

The 2025 Women in Mining USA National Conference, held April 15-18 at the Grand Hyatt Riverwalk in San Antonio, TX, brought together hundreds of professionals for a fourday event focused on empowering women and creating space for all individuals in the industry. Under the theme “Empowering the Future of Mining,” the conference served as a dynamic platform for professional development, knowledge-sharing and cross-sector collaboration. Organized by Women in Mining USA (WIM USA), whose mission is to foster equity, sustainability and leadership in mining, the event featured an extensive agenda including workshops, keynote speeches, panel discussions and networking opportunities. Attendees ranged from industry veterans to emerging professionals and students, united by a shared commitment to progress within one of the world’s most essential and traditionally maledominated sectors.

Jun 1, 2025

By Carrie Smith

In 1972, in Denver, CO, five women with a shared goal joined forces to create the first formal space for women in the mining industry: Women in Mining USA (WIM USA). When the organization first took shape, few could have predicted that a small gathering of women would grow into one of the most influential organizations that would advocate for inclusion in the industry. Now, more than 50 years later, the group remains a vital network for professionals across the United States with a diverse array of membership and chapters.

Jan 1, 2026

Automated drilling in surface mines is here, it?s successful, and it?s already at work in mines around the globe. Coal, copper, iron and gold mines in large mining countries such as Canada, Australia, South Africa, the United States and Chile are meeting mining objectives previously ruled out as unattainable. Pit Viper automation enables operators to accomplish more objectives safely. Operator assist functions like AutoLevel, AutoDrill, Auto Rod Changer and multi-rig teleremote control are a few of the features mines are using to gain consistent, sustainable productivity.

By Gary PE Beerkircher

A brief history of banana screen development and evolution will be presented along with the operational advantages of the large banana screens available in the industry today. Applications of the large banana screens will be presented as well as the economic advantages that the use of large banana screens can offer to the Mining lndustry today. Banana screen installations in metal, non- metal and coal mining applications will be presented.

Jan 1, 1997

By Rex L. Outzen

Houston International Minerals Borealis Project is an open pit heap leach operation. The operation uses open pit mining, two stage crushing, agglomeration, heap leaching, zinc precipitation and induction refining to produce approximately 50,000 ounces of gold per year. Due to the ore being extremely ameanable to heap leach processing techniques, low manpower requirements and efficient management, the operation is one of the lowest cost gold producing operations in the United States.

Jan 1, 1984

By Thomas J. Lien

AMAX Coal Company has constructed the first commercial demonstration sub-bituminous coal dryer at its Belle Ayr Mine south of Gillette, Wyoming. This 215 ton per hour facility is projected to produce 165 tons per hour of dried coal at 10 percent moisture and 10,800 Btulpound (6,000 KCIkg). Approximately 43 tons per hour of water will be removed from the coal and seven tons per hour of coal burned as fuel.

Jan 1, 1989

By J. H. Ahn, J. E. Gebhardt, W. K. Tolley

Color measurements were made for pure minerals, mineral mixtures and flolation froths loaded with different minerals. The research objective eras to correlate color with the composition of mineral streams. An industrially available system consisting of a fiber-optic-based illuminator and detector was used to measure color. The color values of binary mineral mixtures varied according to the type and proportion of minerals in the mixture. The measured color values of mineralized froths in the laboratory and in a commercial flotation circuit were dependent on the amount and type of minerals present.

Jan 1, 1994