Search Documents

By Henry P. Ehrlinger III, Latif Khan, John M. Lytle

The primary purpose of this project was to produce and test coal concentrates made from coal preparation plant waste fines for use in a slurry-fed gasifier. Concentrates from several individual waste streams were examined to determine their amenability as feedstock for a slurry-fed, slagging, entrained-flow gasifier. The tests included analyses of the plant feed and product, material balances, and estimates of gasification reactivity and of pumpability. The following preparation plant fines were examined: • fresh rejects produced in a plant processing underground- mined Springfield Coal • fresh rejects produced in a plant processing underground- mined Herrin Coal • fresh rejects produced in a plant processing surface-mined Springfield Coal and Herrin Coal • Five-year old impounded fines rejected during processing of underground mined Herrin Coal. At high coal recoveries the Btu content of the concentrates was greater than the Btu content of the utility product from the plant. The coal recovered from fines was found to be entirely acceptable for gasification and pumping without additives.

Jan 1, 1995

By Norman D. Harte, George W. Holl

The development of the most important tool used in Site Testing is reviewed briefly and the application of the information gained is described. The operation of Site Testing and pregrouting of underground excavations is dealt with in detail. Practical experiences (and pitfalls into which the inexperienced might fall) are recorded. But for the application of Site Testing and grouting of shafts, tunnels and other excavations, vast areas of the present goldfields in South Africa would remain unexploitable.

Jan 1, 1981

By Tomb. T. F., R. A. Haney

During the past several years, the Mine Safety and Health Administration (MSHA) has conducted studies in underground mining operations to obtain information on occupational exposures to diesel particulate (DP), mine environmental DP levels and on the effectiveness of methodologies used to control DP. The studies conducted were representative of four coal mines and 10 metal mines. The metal mines included two lead-zinc mines, one limestone mine, two potash mines, one zinc mine and four salt mines. Three of the four coal mines were using disposable diesel exhaust filters to remove particulate from the exhaust and one was using a reusable wire mesh filter. Results of these studies indicate that average DP levels in coal mines not using exhaust filters range from 0.9 to 2.1 mg/m3, The use of exhaust filtration devices reduced these levels by about 50% to 90%. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1996

By V. Srajer

This paper deals with the problem of efficiently selecting the most appropriate loading and hauling equipment for surface mines. Problems and factors that affect productivity and operating cost are identified. During the course of collecting the information for this study, mining companies and equipment manufacturers were interviewed to define their selection practices. The majority of mining companies prepare general specifications and ask the suppliers to mate those specifications to their product line. The mining company then evaluates various proposals on the basis of the best available deal. The following 'mines from western Canada provided information for this study: Coal Mountain, Line Creek, Quintette, Westar's Harmer mine from the Province of British Columbia, and Coal Valley, Gregg River, Highvale, Luscar from the Province of Alberta.

Jan 1, 1989

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994

By D. E. Ranta, Leigh A. Readdy

Defining classes of ore using geostatistical methods that match historical classifications has presented problems in the past. A simplistic and practical approach to this problem is presented. An example of the approach is presented using a porphyry-type system as a case study. The technique described uses area of drill-hole influence and known conditions from similar deposits, or the production history of the deposit being studied. It provides a practical bridging mechanism for defining the class of ore on a block-by-block basis using the error of estimation value developed during kriging. The approach provides a filtering method that refocuses attention on the adequacy of drill-hole spacing.

Jan 1, 1992

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Yiming Sun, John Stolz, Jakob Walter, Drew Mason

The Courthouse Commons SEM Tunnel was excavated within 6 feet of cover beneath two buildings in downtown San Diego utilizing high-precision geotechnical instrumentation. The excavated dimensions are approximately 25 feet in diameter and 328 feet in length connecting two in-service detentionlevel security buildings. Presupport includes large-diameter grouted canopy pipes and smaller pipe spiles. Initial support consists of fiber-reinforced shotcrete with lattice girders. This paper presents observed ground and structure behavior and lessons learned. During construction an unanticipated brick structure was encountered, and methods were developed to improve adhesion of shotcrete to sandy soil and to reduce rebound

Dec 1, 2022

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By Jerry Demchuk, Allan Flemming, Stephan Day

Luscar Ltd. is currently developing open pit mining plans for the Telkwa Coal Project. Most waste rock is predicted to be non-acid generating but a proportion (less than 20%) is potentially acid generating. The waste management plan includes in-pit and ex-pit disposal of blended and till-capped waste rock, segregation and in-pit encapsulation of strongly potentially acid generating materials, and in-pit underwater disposal of coarse and fine tailings. The paper will present the steps used to design the waste management plan including the development of geochemical design criteria using various tests and theoretical and practical knowledge of waste behaviour.

Jan 1, 2000

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987

By Charles T. Staniek

Following a dragline relocation at Agrico's Fort Green phosphate mine in 1986, the recovery plant experienced a significant decrease in flotation performance. Through weeks of trial and error testing, we discovered we could restore recoveries by conditioning feed at pH's higher than we had used historically. The higher pH's essentially increased flotation cell kinetics, although we still do not understand the exact mechanism at work. Armed with new-found appreciation of pH modification, we initiated a program to determine the optimum modifier for us, from both a performance and environmental perspective. Environmental considerations were important because ammonia, the standard industry modifier, is a plant nutrient and higher usage rates could affect the quality, of our recycle process water. This paper describes the research and development work spanning a 3 year period that culminated in making a major change in our reagent suite when we replaced ammonia with soda ash on a permanent full-time basis.

Jan 1, 1993

By Bruce Congleton

The Florida phosphate industry is a leader in environmental control, both in terms of dollars spent and significant achievements. For instance, since 1960 the phosphate industry has spent over $71 million for air pollution and control devices, including installation, research and development and maintenance. Water pollution control expenditures also total in the millions, with over $69 million spent in the same 10 year period. The industry also is a leader in water conservation measures, having spent nearly $ 18 million since 1966 for conservation devices. Since phosphate is mined by strip mining, land reclamation plays an important part in the environmental control picture. Here again, the phosphate industry has met the challenge with a voluntary program of reclamation which accounts for over 20,000 acres of land useable after mining has taken place. In terms of progress in environmental control, the industry has been able over the years to solve within the limits of technology the fluoride emission problems it once had, and is currently at work solving sulfur dioxide and particulate problems. In just the past year the industry also has been extremely successful in limiting phosphorus and nitrogen discharges into area streams. The industry continues to cooperate with state and local pollution control officials on matters of environmental control, and future plans include even closer cooperation and assistance, as well as increased expenditures.

Jan 1, 1972

By Ora H. Rostad

Some gold production was obtained from placer deposits in Puerto Rico during the period of Spanish colonial rule, but most of the gold was produced prior to 1536. There had been no significant hard rock mining, other than in quarries for road metal or construction purposes or for raw materials to make cement, prior to 1954 when the government of the Commonwealth of Puerto Rico recognized that changes in the mining code were necessary to stimulate exploration for metalliferous ore deposits. The Puerto Rican Legislature passed an act (No. 6), which was approved on Oct. 6, 1954, that reiterated that the title to all "commercial minerals" is vested in the Commonwealth of Puerto Rico. The act provided for the establishment of a Mining Commission, stipulated the power% with which the Mining Commission was vested, and provided that no one may dispose of "commercial minerals" in Puerto Rico without a Commonwealth grant issued on its behalf by the Mining Commission. Act No. 6 also provided for prospecting permits, mining leases, and grants. The Mining Commission, by authority granted to it by Act No. 6, adopted regulations effective Nov. 21, 1957, relating to prospecting, leasing, and producing commercial minerals in Puerto Rico. Royalty rates were also specified for various types of deposits at different annual tonnage production levels.

Jan 1, 1991

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By I. Nishkov, L. Alexandrova

The kinetics of froth flotation and the three-phase contact (TPC) parameters are studied at temperatures varying from 20°C to 40°C. The material floated consists of glass spheres and a quartz particles with various diameters. Dodecylamine hydrocloride (DDAHCI) is used as a collector. The equilibrium three-phase contact angle is measured with a microscope technique using the modified Mingins-Scheludko method. Using a Wilhelmy method, the temperature effect on the surface tension of the DDAHCI solution is determined. The formation of the thin film on a polished plate of vitreous silica and the expansion of TPC is monitored by means of a metallographic microscope and recorded on a attached camera at different temperatures. The experimental data show an intensification of the flotation kinetics at 30 and 40°C in the case of small particles. Such an intensification is not observed with the larger particles. The cause for intensification of the flotation kinetics is sought for in the dependence of the TPC rate of expansion and induction time on temperature.

Jan 1, 1995

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, G. M. Walker, N. Iles, R. D. Chandler, Regis Stana, B. Duddy, Patrick Zhang

Phosphoric acid is a major raw material for the production of ammonium phosphate (AP) that is used as an intermediate in fertilizer production. Impurities within commercial grade wet process phosphoric acid are important in producing a fertilizer granule with good handling properties. The impurities identified as being important are; iron (III), aluminium and fluorine-containing compounds. Results show that the viscosity of the AP slurry produced increases by increasing the amount of impurity in the acid. Bench scale tests have been successfully replicated on a plant scale leading to a better understanding of the composition of impurity levels within phosphoric acid required to produce a high quality, free flowing, hard, spherical and non-caking granular fertilizer.

Jan 1, 2002