Search Documents

By P. Somasundaran

Beneficiation by froth flotation, which exploits the difference in surface properties of minerals, has been a promising method for coal cleaning. However, dissolved mineral species present in coal flotation systems can interact with particles and other species leading to drastic effects on flotation. Particularly, precipitation or adsorption of such species on the particles can alter their surface properties and thus influence the efficiency of coal cleaning. In this work, the bulk and surface precipitation of the dissolved mineral species present in Pittsburgh No. 8 coal was investigated under controlled experimental conditions. Changes in the surface properties of coal due to the precipitation were monitored by following zeta potential. Solution potential data were used to elucidate the mechanism of the precipitation. The effect of the precipitation of the dissolved species on the floatability of coal was found to be marked.

Jan 1, 1995

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By Christopher Haycocks, Randolph Reed, Erik C. Westman

The industrial Source Complex (ISC3) model is the accepted standard used to predict emissions of particulate matter less tan 10µm in diameter (PM10) from industrial operations. This model, however, over-predicts PM10 emissions from surface mining operations, making permits harder to obtain. The over-prediction is likely due to the fact that the model applies emissions from mobile (dynamic) sources to stationary (static) areas. Utilizing a Gaussian dispersion equation, a Dynamic Component Program was created to correct the over-prediction of the model and results in a much more realistic modeling of actual conditions from mobile sources.

Jan 1, 2002

By F. F. Aplan

Rather than reiterate what is well known about the flotation of the non-sulfide minerals, emphasis has been placed on those separations which are not so effective. These difficult separations are largely connected with problems of selectivity in the flotation of the base metal oxides, the other slightly soluble minerals, the insoluble oxides and the naturally floatable minerals. The paper discusses possible methods of improving selectivity between similar species and of improving selectivity against the gangue minerals.

Jan 1, 1994

By Chen Chuanqing

The Mining design system is a CAE (Computer Aided Engineering) software and was developed as designer-oriented, interactive mode software to perform geological and mining design calculation and graphics. To perform geology and mining design, the deposit model files created by the software "Deposit Modelling System", are transferred to the environment of graphics support software, then a specially developed drafting submodule can be selected to proceed to interactive graphics design. If it is necessary to calculate the grade and quantity of a particular part of the ore-body, another submodule will be called and run. The resulting file is 'transferred back, and the recalculation program takes the data from the file and refers to the deposit model file to create a summary reserve report: The minimum hardware configuration of the system are IBM-AT Basic work station with high resolution graphic monitor and peripherals needed are digitizer, plotter, printer.

Jan 1, 1989

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996

By G. Oswald

The fatty acid flotation process has been used to produce phosphate for decades, yet the chemical mechanism involved has never been thoroughly investigated. A basic knowledge of the process is lacking, and as such, industry has had to develop their own guidelines for the design and operation of conditioning and flotation equipment. These guidelines are the result of many trial and error attempts, and are not by any means universally endorsed. There are almost as many opinions about how to operate a plant as there are practitioners of the art. This paper covers the currently recommended rules for design as viewed by one practicing phosphate metallurgist.

Jan 1, 1993

By Carol Cox Russell

More than two thousand abandoned mines within the Animas watershed in Southwestern Colorado are being prioritized for remediation by the Animas River Stakeholders Group (ARSG). Phased collection and assessment of information progressed from large scale to site specific. Prioritization was based on existing or potential environmental impact and technical feasibility of remediation as measured by dissolved Cd, Cu, and/or Zn in the discharge; indicators of habitat degradation; aquatic life in streams; cumulative impacts at the point of compliance; cost effectiveness; treatiblity/feasibility; and cultural and historic preservation.

Jan 1, 2000

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

By C. L. Schneider, R. P. King

Size distributions and liberation spectra were measured in samples taken from 10 streams in a taconite milling circuit under normal operating conditions. The size distributions were deter- mined by sieving and the liberation spectra by image analysis using the linear-intercept method with proper stereological correction. The measured data were used to validate a simulation of the milling circuit using MODSIM which included the calculation of both size distributions and liberation spectra. Both the measured data and the simulator showed that liberated magnetite was returned to the mill in the cyclone underflow. The simulation will be used to improve the economic performance of the plant.

Jan 1, 1995

By Timothy M. Dyhr, Marie Garrett

The Cannon Mine gold project has been perceived as unique for being developed in an area characterized by orchards and suburban residences. The Cannon Mine was permitted and developed successfully in this setting. However, the ability of companies to permit, develop and operate mines in mated areas is becoming more difficult as a result of opposition by residents and increasingly stringent regulation. The challenge to the mining operator in the future on otherwise economically attractive mineral deposits will be the ability to explore and develop these types of projects successfully and cost- effectively

Jan 1, 1987

By A. Maréchal

It has been shown since a few years that the problem of estimating recoverable reserves should be solved by using specialized statistical techniques : whenever the selected blocks are chosen without any other constraint than a cut-off grade criterion, the problem of estimating the corresponding tonnage-grade curve is resolved by estimating the local histogram of block grades. Two major statistical techniques are currently used by geostatisticians to estimate local histograms : the "average conditional distribution" technique (Parker, Journel, Dixon 1979) and the disjunctive kriging technique. (Matheron, 1976, Jackson, Maréchal, 1979). Both have proved to be applicable in practice, with their pros and conconcerning their practibility and versatility.

Jan 1, 1982

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979

By K. V. S. Sastry

Pelletization, sintering, and pressure compaction are the most common methods used to agglomerate ore concentrates. Over the last 20 years agglomeration has grown enormously in popularity and has become a standard unit operation in the nonferrous, cement, fertilizer, and ceramic industries. However, it is in the processing of iron ores and the preparation of blast furnace feed that agglomeration is used most and its application has grown fastest (Ball, et al., 1973; and Sastry, 1977). This chapter deals with an account of the current practices and future trends in the application of computers relative to an overview of the process design and engineering considerations of the unit operation of agglomeration.

Jan 1, 1979

By J. Paraszczak

With regards to the cost and profitability of a mining operation, the performance of the equipment employed is one of the key issues. Cost and profitability depend on, among other factors, the reliability and availability of the equipment. In an attempt to reduce equipment downtime, it is indispensable to collect and analyze reliable data and information on failures and maintenance actions. This paper reviews common problems encountered in this respect, with particular emphasis on the lack of uniform terminology and methodology. Recommendations concerning the standardiztion of reliability and maintainability concepts and measures are given. Regarding the benefits that the latter may bring, the paper concludes with a proposal for an industry-wide initiative in this respect.

Jan 1, 2002

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991