Search Documents

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By R. T. Swinderman

This paper discusses a series of tests designed to help answer the age old question: ?How much does the belt cleaner wear my belt?? The experimental set up and test method are described. The main variables are: belt cleaner blade materials, cleaning pressures, cleaning angles, belt speeds, and belt top cover grade. The bulk material used is a standard test-grade silica sand. The measured results include: blade mass loss, belt mass loss, and cleaning efficiency.

Jan 1, 2010

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This paper describes the successful mechanized extraction of coal pillars in 11 panels using the fish-tail method from 2010 to 2017 at Pinoura Mine in India. This method proved its potential of coal recovery with efficient strata control under weak roof due to faster rate of extraction in a single lift. Observations of strata and snook behavior during the field studies in different panels of the mine are included.

By B. R. Addison

In the Spring of 1991, Georgia Marble Company of Arizona (GMCOA), acquired the Andrada Marble Company located near Vail, Arizona, approximately 32 km southeast of Tucson. The Georgia Marble Company operation consists of an open pit quarry and a recently constructed, state of the art calcium carbonate milling and processing facility. The open pit quarry exposes white, crystalline, CaCO3, Escabrosa limestone that meets our customer criteria for Consumer and Industrial Filler applications. The Georgia Marble Company Arizona Division facility is designed and engineered to produce a wide range of milled calcium carbonate that includes finely ground and coarse screened products.

Jan 1, 1994

By T. B. Szwilski

The paper gives an account of the development of a mine health and safety program in China from 1987 to 1996. The project was funded by the United Nations Development Program and managed by the International Labor Office (ILO). The objective was to strengthen the capability of the National Safety Training Center (NSTC), located near Beijing to train more than 2,000 engineers per year, and provide consulting and informational services to 39 safety training centers and coal mines. Presently China has the highest mortality rate in the world for coal mine operations, the greater incidence occurring at the many thousands of small, unlicensed underground mines.

Jan 1, 1998

By D. C. Shumway

Mining in Cushenbury Canyon began in 1860 when John Cushenbury left his Holcomb Valley gold prospect and discovered a silver vein in the limestones of the present day Cushenbury Mine. Cushenbury Canyon is located along the western boundary of the Mojave Desert in Southern California and on the north slope of the San Bernardino Mountains. The Holcomb Valley, immediately southeast of Cushenbury Canyon was the most prolific gold producer in Southern California. Gold mining dominated the area until World War II when interest in the Lucerne Valley Limestone deposits was peaked by the construction of the Kaiser Steel Plant in Fontana, California. The steel making process required large amounts of metallurgical grade limestone and Kaiser geologists located claims in most of the limestone deposits. Kaiser Cement constructed a cement plant and limestone mine in Cushenbury Canyon in 1956. Kaiser Cement modernized the facility in 1982 to a four stage preheater-precalciner system. Mitsubishi Cement Corp. purchased the property in April, 1988, and through further system modifications have created the most efficient and modern cement plant in the United States.

Jan 1, 1992

By Terrence Chatwin, Michael Sweeney, Steve Accardo

Sutter Gold Venture excavated an exploration decline into a mineralized zone in the Sutter Creek gold mining district. Delays in obtaining the conditional-use permit resulted in 7 to 10 million gallons of water accumulation in the decline containing elevated dissolved arsenic. Sutter received a permit to land apply the water after reducing the arsenic concentration to 0.05 mg/L. Initially the water was treated by co- precipitation arsenic with ferric hydroxide. Operational difficulties of this treatment system resulted in Sutter pursuing alternative treatment methods. The activated alumina adsorpting was selected due to its flexibility and ease of operation. Operating and maintenance data and costs will be presented.

Jan 1, 1995

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

By Alexander Filimonov, Yury Bloshteyn

Ventilation of gas mines keeps necessary sanitation and hygienic conditions for labor in mines and increases the safety by dilution and removal of hazardous and dangerous gases in accordance with the safety rules. Several different concepts exist at the present time to design mine ventilation control systems. But technical ideas have been developed inadequately and technological solutions have not been investigated experimentally enough to build a serviceable system. This paper presents a new concept of high- efficiency mine ventilation process control system (MVPCS). The methods of modern system engineering (Kalman, 1969) are used to establish its functional and algorithmic structure. A three level hierarchical principle of system building is considered.

Jan 1, 1991

By Odin D. Christensen

Gold deposits of the Carlin Trend occur within sedimentary rocks deposited across the Paleozoic continental margin. Lithologically dissimilar units, juxtaposed along the Roberts Mountains Thrust Fault system, constitute three distinct stratigraphic packages: autochthonous miogeoclinal carbonates, allochthonous eugeoclinal siliciclastic rocks, and an overlying coarse clastic overlap assemblage. Gold deposits occur within all three stratigraphic packages, with economic concentrations localized at structural and stratigraphic settings similar to those which host petroleum traps. Along structural breaks, gold is selectively concentrated within favorable stratigraphic units. Host stratigraphy controls the character of the ore, including average grade, grade variability, physical properties and metallurgical response.

Jan 1, 1989

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By Lisa Shevenell

Three pits at the Getchell Mine contained water during a hiatus in mining activity (1968-1983). For this period, expected concentrations of As, C1, SO4 and TDS resulting solely 16om evaporative concentration were computed. Computed values are 1.6 to 2.3 times greater than those measured in local groundwaters. However, computed values fix As, SO4 and TDS are lower than measured values in the pit lakes. In some cases, the computed values are only 8% of the measured pit lake values, indicating a major control on water quality via water-rock interactions. In contrast, computed C1 values exceed measured pit lake concentrations.

Jan 1, 2000

By André Vervoort

The roof behaviour in room and pillar panels during the development of roadways and the subsequent pillar extraction was monitored underground and numerical simulations were conducted. For several underground sites, a satisfactory, correlation was found between underground measurements and three-dimensional numerical simulations using a boundary element code in the linear elastic domain. However, to simulate bed separation, and roof block collapses more complex models were required, of which examples are presented.

Jan 1, 1992

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Steven Brown, Richard Stephenson, Richard Partch, Hongyu Wang

Filler technology has enjoyed a revolution in attention and achievement in the past half century. The genesis of the advancements is greater find a mental understanding of the synthetic chemistries for and physical properties of colloidal matter and instrumentation capable of characterizing particle size, shape and surface features. Several advanced chemical methods for processing powders are now employed in ceramic, electronic, imaging, medicinal and plastic technology. This presentation will highlight solution phase synthetic methods for in situ coating of fillers such as SiC, Al2O3, AlN and SiO2 and some properties of the product solids.

Jan 1, 2003

By Kenneth N. Han, Peter Mam-soo Kim

The extraction behavior of gold in ammoniacal solutions in the presence of bromine as an oxidant has been studied. The effect of concentration of ammonia, bromine, and pH of the solution on the rate of dissolution of gold was investigated. The dissolution behavior has been analyzed using electrochemical method, and its results were compared with direct leaching tests using gold powder. The overall dissolution of gold in ammoniacal solution containing bromine was found be affected significantly by pH of the solution and the concentration of bromine. The rate expression found in this study has the following form.

Jan 1, 2005

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010