Search Documents

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By P. K. Chatterjee

Before coal can be extracted from surface or underground mines, approval must be obtained from state and federal authorities. Permitting is the application process through which such approval is sought. The application includes en environmental impact statement Which focuses on Such topics as subsidence, toxicity of acid mine drainage, pollution levels of rivers and streams, post mining reclamation, and the effect on the hydrological balance of the area. The permitting procedure is extremely time and labor intensive, and requires extensive interdisciplinary knowledge. This paper examines a LISP based permitting procedure which will help to reduce the time taken to prepare and review a permit application.

Jan 1, 1986

By William F. Kane, Eric C. Drumm

Rock slope failures in the Great Smoky Mountains of Tennessee are a continuing problem. A study of the geotechnical factors affecting such slopes was conducted in this geologically complex region. Seven rock slopes, five of which had undergone failure, were identified and mapped. Other parameters were mapped in addition to the standard geologic and geometric parameters. These were joint frequencies across and down the slope, and surface hardness from Schmidt hammer tests. Regression analysis on the various data revealed that Schmidt hammer hardness correlates very well with joint cohesion back-calculated from failure geometries. This approach suggests an alternative means for estimating joint strength.

Jan 1, 1986

By Russell Dittrich

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals doré from ores, principally silver bearing with associated gold coproducts. In late 1995, the Stone Cabin ore body was commissioned and the site began a phased shift from silver dominance to gold dominance. The Knelson concentrator was selected to remove gold from a portion of the cyclone under- flow stream in the grinding circuit.

Jan 1, 1998

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines, are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. Comparative testing of these drill types was performed in Quebec. Based on the test results and on time studies performed in the mines, water-powered drilling was reviewed. The review considered the drilling rates achieved, the infrastructure needed, side effects and health and safety considerations. This study shows that the application of water-powered drills may, under specific conditions, help increase the footage drilled and may improve the working environment. Examples of such applications are presented in the conclusions.

Jan 1, 1997

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By Joe Scheuering, Don Poulter, John Trirnble

Closure of the Grey Eagle Mine tailings impoundment is an example of closing a "wet" tailings impoundment at the cessation of milling operations. This paper presents a summary of tailings cover design and construction, tailings deposition sequences to facilitate closure, construction schedules, costs, and post-closure monitoring. Permit requirements which influenced the design and construction of the tailings are summarized. The performance of the cover and post-closure monitoring issues are also discussed.

Jan 1, 1995

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

By C. D. Elifrits, N. B. Aughenbaugh

Laboratory tests of samples of fine- grained, argellaceous rocks, commonly referred to as shales, have shown that various changes in their moisture content can be correlated with loss of strength. This reaction to a change of in situ conditions at abandoned mine sites when combined with the field relationships at locations where the predominant overburden material is fine-grained, argellaceous, and fractured provides a predictive tool for engineers dealing with subsidence problems. Such a tool should enable engineers to recognize areas that are prone to be affected by surface disturbing subsidence features.

Jan 1, 1987

By L. P. Meade

The need to feed an established talc mill from a crude ore source located closer to the mill prompted the 1986 drilling of a previously mapped, talc-carbonate deposit. This talc-bearing rock had never been considered a potential source of crude talc ore because of the high carbonate content and other deleterious minerals observed in outcrops. Selective mining, in-pit grade control and creative processing have allowed this deposit to be developed into an ore body. By definition, an ore body has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by ore tenor.

Jan 1, 1994

By J. C. Harrison

When Exploraciones Eldorado, S.A. de C.V. finished their first phase of reverse circulation drilling at their La Trinidad property in Sinaloa, Mexico they began immediately with permitting and engineering activities. The first phase of drilling lasted four months and ended in April, 1994. The second phase of drilling ran from May through September of 1994. From May through December, 1994, Exploraciones Eldorado performed the permitting and engineering work for their La Trinidad heap leach mine. The mining permit was submitted to the regulatory agencies in February of 1995 and the first draft of the feasibility study finished one month later. The report outlines the permitting and engineering activities that took place during the second half of 1994.

Jan 1, 1996

A thermomechanistic model was developed for the thermal decomposition of the enargite contained in a copper concentrate at 650° to 750°C in a fluidized bed with an inert atmosphere. At the particle level, the model permits one to predict the thermal profile inside the reacting enargite particles, as well as their thermal cycle. At the macroscopic level, a population-based model coupled to the bubbling-bed fluidized bed model allows one to predict the fractional conversion (dearsenification) of an enargite-bearing copper concentrate.

Jan 1, 2002

By D. Greene

The close integration of mine planning and mine operation continues to be the goal of mine operators. Depending upon the complexity, size and sophistication of the mine, limited success has been achieved in this area. Despite tremendous strides in the development of computer-aided mine planning, digital plans must usually be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in global positioning systems (GPSs), operator displays and mobile computers now enable equipment operators to work directly from on-board digital plans. A computer-aided earthmoving system (CAES) offers reduced survey costs, faster field transition time and improved excavation accuracy, coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 2000

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By M. T. Ityokumbul

Flotation is a surfaced-based separation process that exploits the differences in the hydrophobicities of the components. In the present paper, a review of both established and emerging nonmineral applications of flotation (oil removal, paper de-inking and separation of plastics) is presented and discussed. For each application, the theory of the process is compared and contrasted with mineral flotation. It is shown that the mass-transfer approach to flotation offers a good starting point for the analysis of these separation processes.

Jan 1, 1999

By R. Vergunst, E. A. Devuyst, G. Robbins

By the middle of 1989 Inco will have applied its patented cyanide removal technology to seventeen commercial operations. Removal of cyanide from CIL slurry tailings is applied at Equity Silver and Inco's new 1.200 mtpd mill at Inco/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3.600 mtpd), Canamax's Ketza River (360 mtpd) and Westmin's Silbak Premier (2000 tpd) operations. Repulped tailings from Merrill-Crowe flowsheets are treated at Total Erikson's Mount Skukum (300 mtpd) and Skyline's Johnny Mountain (200 mtpd) mills and barren bleed at Inco/Queenston's McBean mill (500 mtpd). Lynngold's MacLellan mill (1800 mtpd) and ERG (40.000 mtpd) treat pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating and two other plating shops in Ontario. Details regarding some of the above operations are given. Operating and capital cost estimates for various treatment options are discussed.

Jan 1, 1989