Search Documents

By S. Ersayin, I. Iwasaki

The application of a magnetic field was shown to be effective in controlling iron losses in a pilot-scale cationic silica fIotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42-m3 (50 cu ft) WEMCO flotation cell are reported. Major losses of iron units in froth products were in the -25-µm (-500-mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The "as-received" sample was sufficiently magnetized, and no further benefit was gained by the magnetizing treatment. The selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be readily installed in existing equipment. Key words: Iron ore, Flotation, Taconite concentrates, Cationic silica flotation, Magnetic field, Flexible magnetic sheet, Magnetizing, Demagnetizing

Jan 1, 2003

By William H. Schiffbauer

Research is being conducted toward making underground mining equipment autonomous. This will facilitate improvements in safety by relieving workers of dangerous tasks and will increase production by providing more accurate control with less down time.. A Bureau of Mines developed microcomputer network has enhanced this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of intelligent sensors, computers, and microcontrollers. Descriptions of the mining machine, the mining machine control computer, control algorithms, -the microcomputer network architecture, and communication protocols are discussed.

Jan 1, 1989

By A. E. Strakele, M. W. Springett, S. N. Watowich, W. F. Matlack, E. Yeomans, S. L. Manske, B. Yeomans

The Mesquite gold deposit is a large, low-grade "disseminated" ore body located in the Chocolate Mountains 65 km (40 miles) northeast of El Centro, CA. The deposit is tabular in geometry with a gentle southwest dip, concordant to a sequence of quartzofeldspathic to mafic gneisses. The host gneisses are amphibolite grade and intruded by synkinematic leucogranite and pegmatite. Reset potassium-argon (K-Ar) dates of 32 to 38 m.y. on mineral separates from gneiss in the ore body are suspected to reflect the age of mineralization. The hypo gene mineralization was introduced with siliceous breccias and -quartz veinlets and consisted of argentiferous native gold associated with minor pyrite and other base metal sulfides. Fluid inclusion study of gangue quartz indicates that the hydrothermal system contained a 225°C (437°F) boiling, 1 wt % NaCl equivalent solution with a small amount of CO2-A high degree of post-mineral faulting and fracture has resulted in deep oxidation and has obscured the original geometry and hypo gene mineralization of the ore body.

Jan 1, 1987

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By G. Schmelzer

The disposal and reintroduction into recycling of residues produced by today's industrial society is not only a problem of much public debate in the countries concerned but also an increasingly prominent topic in science and research. In the treatment of most types of waste, ecological as well as economic considerations are important factors. In view of this, not only will future expenditures for treatment and processing become more significant but also, on the other hand, the savings and profits resulting from recycling. The situation described above reflects the inherent problems in the treatment of solid residues produced by waste incineration plants. The incineration of municipal waste produced approx. 2.7 - 2.8 million tonnes of solid residues in 1993 in the Federal Republic of Germany, which in part included still considerable amounts of organic and inorganic pollutants that could potentially be released into the environment. The most significant of these in terms of volume is incinerator ash at approx. 2.4 million tonnes. Through the use of innovative processing techniques, attempts are being made to convert the residues into a form that remains environmentally neutral over the longest period of time possible. One such group of techniques includes smelting technologies. After it has undergone specialised treatment, mineral incinerator ash is converted into environmentally neutral and reusable glass (vitrification) since, besides a reduction in the volume of the residues by approx. 90%, the main goal is a complete immobilisation and destruction of inorganic and organic pollutants respectively. These glasses, after they have been reshaped, are resold as commercial products such as damming or form glass.

Jan 1, 1995

By Clete Stephan, John Urosek, Ian Anderson

The Endeavour Colliery is operated by Powercoal Pty Ltd. It is located in the Central Coast of New South Wales, Australia. The mine has been in operation for about 30 years, producing around 600,000 tons of export coal annually from two production sections. On June 28. 1995, an explosion occurred underground in the 300 Panel at approximately 9:50 a.m.. There were thirty miners underground at the time of the explosion, all of whom were safely evacuated. From June 29 through July 10, personnel did not enter the mine. However, gas samples of the mine atmosphere were obtained from underground monitoring stations and analyzed. Samples were also obtained from boreholes that were drilled from an adjacent mine. On July 10, the atmosphere at the underground monitoring locations and at the boreholes appeared stable with minimal risk of combustion occurring underground. Plans were developed to begin the recovery of the underground workings. The recovery of the underground workings was completed on July 13. The underground investigation of the explosion began on July 14. The investigation was conducted by the New South Wales Department of Mineral Resources. Technical assistance was pro- vided by the United States Department of Labor's Mine Safety and Health Administration (MSHA).

Jan 1, 1997

One of the largest mining shows in the world is set take place April 15-18 in Santiago, Chile. Expomin 2008 is expected to attract more than 60,000 professionals from around the world who are involved in all aspects of the mining industry. Expomin has become an important place for mining leaders to meet, organizers said, ?with great expectations for the development of new business in international markets.? This is the 10th Expomin. The event, held every two years, is expected to at-tract exhibitors from more than 25 countries, representing nearly 1,000 companies and more than 3,000 brands related to the mining industry, organizers said. Most all of the world?s largest equipment manufacturers and suppliers ? surface and underground ? will be represented. The importance of the event to the Chilean and international mining industry can be seen by the increase in size of the exhibition ? 13 percent more surface space in 2008, compared with the 2006 Expomin. The exhibit will be broken down into four pavilions, covering 34,054 m2 (355,570 sq ft). An outdoor area for the large mining equipment will cover 16,120 m2 (173,520 sq ft).

Jan 1, 2008

By U. E. Paakkinen

Progress in computer control of flotation circuits has developed parallel with advances in reliability of on-stream X-ray analysis (Cooper, 1976). Attainment of acceptable results with X-ray fluorescence analysis over the past ten years has led to application of computer control in more than 30 concentrators. Gains in applying flotation control also have given incentive to improving measurement and control devices for other essential functions in control systems. At the same time, advancing technology has made available computer systems having characteristics practical and economical for the physical environments of concentrators and ore processing plants. Benefits from flotation control have centered on increased efficiency in mineral separations, derived by stabilizing circuit operation subject to changing ore characteristics. The gains have been most evident in processing complex ores for multiple concentrate products. In many cases, particularly when coupled with grinding control, the economic results from on-line control have been substantial compared to investments in monitoring and control equipment.

Jan 1, 1979

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By W. M. Husslage, M. E. Kock, T. Bakker, R. H. Heerema

Permeability in the blast furnace shaft is adversely affected by low-temperature reduction degradation of sinters. The fundamental cause of this is the expansion of the iron oxide phase resulting from the reduction of hematite to magnetite. The present study shows that expansion behavior during the hematite/magnetite reduction .step and the resulting microstructure are strongly influenced by the reduction temperature (partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed that can explain the dilation behavior and the magnetite microstructure. The results provide better insight into the reduction degradation behavior.

Jan 1, 2000

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By A. Redfern, B. G. D. Smart

The ultimate objective of the development work presented in the paper is to devise an appropriate method for relating powered support specification to geological conditions and mining practice, thus enabling the longwall method of coalmining to be successfully implemented throughout the varied coalfields of the world. The paper begins with a review of various methods previously used to determine support rating, each method being analysed with regard to its source, the logic and theory which constitute the method, and subsequent recommendations. An alternative approach is then proposed, the Powered supports being considered to be one of three foundations, sharing load with coal ahead of the faceline which acts as another foundation, and the waste behind the supports which acts as the remaining foundation. The load/deflection characteristics of the coal and waste, which in turn are related to geological conditions and mining practice, are shown to affect the load transfer on to and hence the specification of the powered support. In particular the characteristic of the waste foundation is shown to be affected by the caving mechanism, an alternative form to that mechanism accepted for British conditions being proposed and designated "parting-plane-controlled" caving. A finite element solution for a beam on elastic foundations was used to translate the above concepts into numerical results, these results being compared with data from Indian and Chinese operating conditions. The Indian case study examines the effect of using a conventional chock type of support in a one-web back mode when mining towards a roof break generated ahead of the face, while the Chinese case study compares measured subsidence over a longwall with "blocky" roof conditions with the model results. The comparisons are encouraging, suggesting that the approach used is worthy of further development.

Jan 1, 1986

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By R. H. Lesernann

Copper has held up extremely well as we have moved through the trough of the economic cycle. In the aluminum, lead and zinc industries at least half of the Western World production was unable to cover its operating costs at the prices prevailing throughout most of 1991. In copper, less than 10 percent of production ran in the red last year. Most of that was in Peru where the government has not allowed its currency to devalue at the same pace as inflation. Thus, mining company revenues in local currency terms have risen very modestly while costs have escalated tremendously. Excluding such governmentally imposed distortions, virtually every mine in the Western World ran at a profit last year. While copper producers have to be extremely happy about staying in the black through the trough of the consumption cycle, consumers have to be worried. They must be asking themselves, "If copper held at over $1.00 in a year when consumption declined, how high will prices go when demand picks up?" Consumers are accustomed to paying high prices at the peak of the cycle, but they are also accustomed to paying low prices at the trough of the cycle. What went wrong this time?

Jan 1, 1992

In 1989, United States mine production of barite decreased 13% while world mine production decreased by 8.6%, according to the US Bureau of Mines. Consumption, sold or used by grinding plants, decreased by 21.2%. And imports decreased by 12.8%. The value of domestically produced barite, fob mine, increased 17.4%, according to the Bureau. The declared value cif US port of all imported crude barite during 1989 increased from $38.10/t ($34.56 per st) in 1988 to $40.27/t($36.54 per st). Nevada continued to be the leading producer of barite with 77% of the total, followed by Georgia and Missouri. The Bureau of Mines estimates 75% of the domestic mine production was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass, or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the nonoilfield sector. Of the total consumption used by grinding plants and chemical manufacturers, it is estimated that 80% was used in drilling fluids. The other 20% was used in the non-oilfield sector, including barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1989. The average number of rotary rigs operating was 869, 7.2% less than the average of 936 in 1988. Crude barite imports were down 12.8% from 1988. Imports accounted for 73.8% of the barite consumed (apparent) in the US. China continued to be the leading exporter of crude barite ore to the United States with 63% of total crude ore imports. India followed with 27.4%, Peru 4.3%, Chile 2.9%, and Canada and Mexico, each with 1.1 %. About 97% of the imported barite ore was used in the oilfield sector.

Jan 1, 1990

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By J. M. Applegate, C. L. Morgan

Introduction In the same way that a blueprint communicates informa¬tion about a structure, a systems architecture should provide information that guides the construction and implementation of a computing system. Taking the blueprint analogy a step further, a plot plan can also show where, in the "bigger picture," a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: • the primary purpose of computer-based systems rela¬tive to particular tasks or operations, • the relationship of the systems to each other and an indication of their interaction and dependencies, • the relationship of the systems relative to the organiza¬tion and its objectives, • indications of where IS/IT resources can best be allo¬cated to support the organization and • the overall context in which new systems and technolo¬gies can be assessed for both their impacts on current systems and on the organization itself. In theory, a well-designed systems architecture should allow an organization to focus its resources on those aspects of its business that matter most, thus, leveraging investments in information technology to a competitive advantage. In addition, the way that a computing systems architecture is represented should be un¬derstandable to non-IT staff, and it should be eas¬ily recognized by the people it supports. This pa¬per attempts to show that a meaningful systems model exists and that its applica¬tion to mining can achieve the desired results. The following discus¬sion is based on the au¬thors interpretation of a concept referred to as the computer integrated manu¬acturing (CIM) model, as developed by Allen-Bradley. An inherent strength of the CIM approach is that the model combines aspects of business-reporting structures with the manufacturing process itself. What results is a systems frame¬work that is aligned with relevant business processes and is, therefore, easier for non-IS/IT personnel to interpret. The successful application of the CIM model can be seen in a large number of both discrete and process-manufacturing facilities throughout the United States. This paper provides a brief overview of the CIM model and then describes how the model can be applied at a conceptual level to the mining industry. Finally, this paper proposes an extension to the CIM model that the authors believe will make it easier to understand and apply. CIM model As shown on Fig. 1, the CIM model begins with the most detailed levels of process equipment and works its way up to the highest level of consolidated financial reporting. Systems at each level are characterized by common attributes, users, time frames, etc., providing a clear picture of their interac¬tion. Further analysis of the relationships between systems and between levels provides insight into the opportunities for integration. Regardless of the industry or processes involved, the CIM model provides a framework in which the characteristics of systems and the data they manage can be predicted based on the nature of the business function they support. In general, as data moves upward from the lower rungs of the CIM model, it changes from de¬scribing the physical na¬ture of a process to describ¬ing its financial aspects (e.g., from productivity to cost). The time frame to which data applies also transitions from a very short duration, perhaps only milliseconds, to financial or regulatory reporting time frames that may span years. In a simi¬

Jan 1, 2000