Search Documents

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By B. Emwanu, R. A. Raju

The implementation of new technology in mining can be likened to a paradoxical situation or dilemma, where, on one hand, major mining projects are not able to solicit investor funding unless it is proven that the business cases were developed using tried and tested mining methods. On the other hand, new and innovative mining technology and mining methods need first to demonstrate and prove themselves under real production conditions over a reasonable period before they can be considered bankable feasibility studies in the mining industry. This dilemma locks new mining technology investments in a continuous cycle of underinvestment. Technological innovations are particularly relevant to the mining industry, which deals with the challenges of depleting access to resources, requiring new solutions to remain sustainable and competitive. In the last decade, the mining industry has come to realise that technological innovations can directly contribute to its sustained competitive advantage (Sanchez, Hartlieb, 2020), helping to reduce costs, lessen environmental impact, increase production, and improve mineral recovery. While understanding barriers and drivers for technology adoption is important for the success of technology implementation efforts and the sustainability of the mining sector (Muduli et al., 2013), this paper suggests strategies to exit the dilemma, proposing a preliminary framework.

Oct 24, 2025

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

A method, based on the macroscopic population balance equation allowing the dynamic simulation of a multistage adsorption plant given an arbitrary rate expression, is described. The partial differential equations resulting from this method are simplified using the method of characteristics. The simplified equations can then be solved using standard ODE integration techniques. The procedure is illustrated by means of data typical of a CIP application. Requirements for data structures which allow the incorporation of the carbon-in-pulp (CIP) model (and other unit models) into a general metallurgical simulator are described. Based on these considerations, it is concluded that more generality in the description of distributed quantities such as loading and particle size is provided by the use of mass density at fixed class boundaries, rather than discrete masses within fixed classes as has hitherto been used by ore-dressing simulators.

Jan 1, 1987

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

By P. Kitobo, T. Nduba, D. Mbay, J. B. Vangu, R. Ciband

The flotation plant tailings at Kamoa Copper Mine concentrator were found to contain a high proportion of extremely fine particles. The potential issues with settling these fine solids were resolved by the use of a poly-di-allyl-di-methyl ammonium chloride (DADMAC) coagulant, Flobead DB 45 VHM, in conjunction with a standard anionic polyacrylamide flocculant. This paper outlines some of the issues encountered and how they were resolved at the Kamoa concentrator. The potential to use this process and technology at other sites is also considered

Jan 1, 2023

By A. Marek

The safe and optimal installation of roof support remains one of the biggest challenges in underground mining today. Traditional hand-held, roofbolt installation in conventional mining has been replaced, in a lot of mining operations, by mechanized equipment. This was a first step to moving the operators out of the unsafe working environment and a start on the trend toward a changed support regime in mechanized mining. However, the challenge of handling of the drill steel itself, as well as inserting resin cartridges and bolts, remains a major hazard and the cause of many lost-time injuries. The paper describes and discusses developments in this area, of mechanized bolting and on-board automation, presenting solutions to known problems, achievements to date, and future developments. The solutions presented will identify with addressing customer needs while touching on possibilities for further technology changes, keeping focus on the safety aspect for operators and the need to bring the operators even further away from the unsafe working environment. The-state-of-the-art technology in mechanized bolting equipment is presented and a brief outlook on the past, current, and future developments is given.

Jan 1, 2012

By H. Lieberwirth, M. Klichowicz

The comminution at grain size level for the liberation of valuable minerals usually requires the highest size-specific energy. Therefore, the full understanding of the comminution process at this level is essential. Models based on the Discrete Element Method (DEM) could be a helpful tool for this purpose. In those, the mineral microstructure, which has a dominant influence on the fracture behaviour, can be described in great detail. One major concern, however, is the missing representativeness of simulated models. In this study, a method to overcome this limitation is presented. The authors show how a realistic microstructure can be implemented into a particle bed comminution simulation using a two-dimensional Bonded Particle Model (BPM). The improved algorithm based modelling approach is exemplarily compared to an equivalent real experiment. Thereby, the focus is set on the analysis of the interfacial breakage and the capability of the simulation to reproduce the experimental results. The comparison of the results shows that simulations at grain size level allow a more detailed evaluation of the fracturing behaviour. This is of special interest as the aim of comminution in mineral processing is not only the size reduction of coarse particles, but an efficient liberation of the valuable components. Hence, simulations with automatically generated real mineral microstructures will help to further improve the efficiency of ore processing. Keywords: Discrete Element Method, grain modelling, particle bed comminution, realistic synthetic

Jan 1, 2020

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020

By H. S. Baloyi, J. J. Rust

Spiral concentrators are widely applied to beneficiate commodities such as Cr2O3, mineral sands, and ferrochrome. The application of spirals for heavy minerals has been limited to a feed top size of 1 mm. At particle sizes larger than this, friction retards heavy particles and the particles' primary velocity approaches zero, resulting in a solids build-up, therefore inhibiting further separation. Recently, a new Multotec SC25 spiral model was introduced to the industry, which aids in beneficiating particles of up to 3 mm, with successes having been demonstrated in ferrochrome slag and titanium-bearing minerals. This spiral also has potential in electronic waste applications. This paper examines the applicability of the SC25 spiral in coarse Cr2O3 recovery. This stems from the fact that junior chrome miners tend to discard particles larger than 1 mm as they neither have milling nor dense media circuits. Also, alluvial chrome miners discard +1 mm even though this size fraction contains recoverable and liberated Cr2O3. The SC25 spiral has shown better Cr2O3 separation efficiencies than the SC21 model and with higher SiO2 rejection at saleable grades, thus providing an additional revenue stream specifically for the coarser (+820 μm) size fractions. Keywords: Spiral concentrators, chromite recovery, specific gravity, SC25 spiral, coarse spiral

Jan 1, 2020

By G. Voiloshnikov, P. Koblova, Ye. Musin

Preg-robbing activity of the carbonaceous matter negatively impacts the process of precious metals recovery from gold-bearing ores and concentrates. In this paper, ore heap leaching (HL) using a blinding agent which inhibits ‘preg-robbing’ is a promising method. A carbonaceous ‘preg-robbing’ gold ore with head gold grade of 1.92 g/t from a Russian deposit was studied. Corg was 1.12%. In accordance with the Irgiredmet technique, preg-robbing activity was 65.3%. Surfactant reagent DN was used as the blinding agent. Column tests on the ore HL were conducted using two options. They were: a conventional flow sheet (Column 1) and a flow sheet with the reagent addition (Column 2). Gold recovery in Column 1 was 55.39% while gold recovery in Column 2 was 68.48%. The test results confirmed the efficiency of reagent DN. Keywords: Carbonaceous ore, organic blanking, preg-robbing, recovery

Jan 1, 2020

By S. Polansky, J. Kolacz

The new sorting system has been developed to achieve efficient separation at low mineral content levels. The system employs high resolution X-ray sensors providing multi-energy analysis, thus giving maximal information about processed materials measurable by X-ray radiography. It makes it possible to analyse the internal structure of the particles and directly detect inclusion of minerals and metals like copper or gold. The paper describes sorting application examples for zinc, lead, copper and gold ore with low metal content below 0.1% of Cu. The sorting system still allows high efficiency analysis, quantification and removal of rock particles representing waste fraction with no metal or a negligible amount being uneconomic to process. This brings a huge advantage during pre-concentration, where almost no losses of valuable minerals in the waste fraction can be achieved. The presented sorting system has been developed by Comex and X-MINE EU Project Consortium. Keywords: X-ray sorting, ore sorting, XRF analysis, XRT analysis

Jan 1, 2020

By L. S. Bicalho, W. J. Rodrigues, P. M. A. Rollo, P. R. G. Brandão, W. C. da Silva

Quadrilátero Ferrífero is an important mineral province located in Minas Gerais state, responsible for a substantial amount of iron production in Brazil. Among the concentration methods for iron ore practised by the mining companies in this region, the most important is the reverse cationic flotation. Dolomite iron formations, with the presence of hematite, quartz and dolomite, occur in several areas of mining and, with the deepening of the deposits, this type of ore, with low iron content and more complex mineralogy occurs frequently. Carbonaceous minerals, mainly dolomite, present a technological challenge for the concentration of iron ore by flotation. In the present study, the concentration of iron ore with 6% of dolomite content was evaluated. Bench flotation trials indicated that conventional iron ore flotation is not selective to float dolomite, thus compromising the iron content in the final concentrate. Alternative flotation routes were evaluated, and a selective condition was reached to float both quartz and dolomite using the combination of the cationic collector Flotigam 16424 with an anionic collector Flotinor 16551. It was demonstrated that the flotation of dolomite was improved with the combined use of both collectors in the cleaner stage, and by a previous quartz flotation in the rougher stage. Zeta potential analysis indicated specific adsorption as the adsorption mechanism between Flotinor 16551 and dolomite, confirming the high selectivity observed in the bench flotation tests. Keywords: Flotation, iron ore, dolomite

Jan 1, 2020

By J. E. Gebhardt, B. Temel Mckenna, W. Lee, C. S. Macomber

X-ray diffraction (XRD) data was extracted from various sources to develop qualitative ternary and tetrahedral plots differentiating mineralogy, bond work index (BWi) and hardness of ore bodies at different mine sites. A large number of historic reports and compiled characterization laboratory data were used to create a searchable "data lake." The data lake provides a means to locate, consolidate, and visually represent XRD from disparate sources. Visualizations with large amounts of mineral ore XRD characterization data provide a qualitative assessment of ore properties, including comminution qualities such as material hardness. The visual map can be employed to quickly estimate expected ore character and behavior, given XRD analysis of samples from newly characterized and unfamiliar ore. Keywords: Mineralogy, Characterization, Comminution, Database, Ternary, Tetrahedral

Jan 1, 2020