Search Documents

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

The first neutrinos in nature ever detected by man were "caught" in a unique laboratory some 3 km (over 2 miles) underground in one of the world's deepest mine shafts at East Rand Proprietary Mines (ERPM), Boksburg. Only 100 m from where gold is being mined from the rock face a small team of South African and American physicists work on one of the most fascinating and important fundamental research projects that is currently exciting the imagination of the scientific world. Neutrinos are sub-atomic particles just as are protons, neutrons and electrons, but they are unique in that they have neither electric charge nor mass. Cosmic neutrinos travel at the speed of light and penetrate stars and planets. Even a million kilometres of solid lead would not provide a satisfactory shield against them. Stars are believed to "burn" by means of nuclear reactions which produce enormous fluxes of neutrinos. The sun, for example, illuminates the earth with visible light, but also bathes it with neutrinos. After World War II, two American physicists, Profs Frederick Reines and Clyde Cowan, experimenting at a large nuclear reactor, succeeded in obtaining direct evidence of the existence of the laboratory-produced neutrino. It then became very important to establish whether neutrinos also existed in nature. This knowledge would lead to a greater understanding of the forces of nuclear physics, of the behaviour of nuclear particles and, indeed, is also relevant to astrophysics. From the start it was clear that the search for "natural" neutrinos would be difficult. Questions which arose were- * how could they be traced if they were without mass or electric charge? * how could other nuclear particles be screened off? * could these not be wrongly detected, or even prevent accurate detection of neutrinos? Neutrinos were known to be produced along with charged particles, by the reaction of primary cosmic rays with the constituents of the atmosphere. It was also known that when the neutrinos collided with matter, they themselves produced the same type of charged particle which could be detected if the unwanted charged particles from the atmosphere could be screened off. What was needed, therefore, was a laboratory where the particles produced in the atmosphere could be screened out, yet which would receive and detect the particles produced by the neutrons' collision with the matter (solid rock) in the vicinity of the laboratory. This meant that scientists either had to build a laboratory with an enormously thick lead shield for their detection work. . . or they could go as near as possible to the centre of the earth where only charged nuclear particles of the very highest energies could penetrate. ERPM was clearly the most suitable place in the world where so effective a "neutrino trap" could be set. Under more than 3 000 m of solid rock the apparatus for detecting neutrinos is well shielded against unwanted nuclear particles produced in the cosmic radiation which can reach the laboratory only in a steeply vertical trajectory. Other particles are easily stopped by the great thickness of rock. The air-conditioned laboratory is at one end of a 150 m long tunnel, 2,5 m high and wide, blasted from the rock. The electronic recording equipment is housed here, while the rest of the tunnel is filled with the detection system. When a charged particle passes through a detector element, it produces a minute flash of light which is recorded and which triggers a flash-tube array. This then defines the trajectory of the charged particle, which is also recorded on film for analysis. So far 82 neutrinos have been detected, 50 at the present level and 32 at a higher level, and the findings have borne out the physicists' theoretical expectations. In this joint project Profs Reines, J. P. F. Sellschop, Director of the Witwatersrand University's Nuclear Research Unit and M. F. Crouch of the Case-Western Reserve University of Ohio are the Chief Investigators. This unique endeavour has been made possible by financial support from the US Atomic Energy Commission, the University of the Witwatersrand and the Chamber of Mines of South Africa, as well as by the cooperation of the management and men of ERPM.

By R. C. J. Goode, W. S. Rapson, W. R. Lawrie, L. W. P. Van Der Bosch

W. R. Lawrie (Member): As all the Institute members present are aware, the Ninth Commonwealth Mining and Metallurgical Congress was held in Great Britain from 3rd to 24th May, 1969. The Congress opened in London and the first week was devoted to technical sessions. Several receptions and other forms of entertainment were held in the evenings. The Congress was attended by some 1 200 delegates, many of whom were accompanied by their wives. As can be imagined a large organisation was needed to cater for all the whims of these delegates, to arrange accommodation and to provide transport for the technical trips, for the receptions and for the sight-seeing tours. Papers presented at the technical sessions proved of great interest. It was stimulating to hear of the developments taking place in the various branches of mining and metallurgy. The discussions which developed between men from so many different countries were thought provoking, led to new friendships and most of us made valuable contacts for the future. There were 141 papers presented in the one week. They were given in four separate halls with two, three and sometimes four papers coming up for discussion in each of the three sessions per day in each hall. Among the more interesting subjects were those concerning off-shore drilling and the facilities for production of petroleum and natural gas. Beach mining at Consolidated Diamond Mines drew a large audience. Automation, mechanization and other technical developments were well described and we were brought up to date with modern techniques of mineral prospecting. There was general discussion on the future of the mineral industries together with comments on the consumption and price trends of these metals and minerals. The future of uranium, of vital interest to us in South Africa, came in for much debate. During the first week, besides attending the technical sessions and seeing some of the sights of London, we were royally entertained. There was a banquet, attended by some I 400 people, where we were welcomed by Princess Alexandra, a reception by H.M. Government in the Banqueting House, and we were entertained at the House of Lords on a terrace overlooking the bustling and rather muddy river Thames. Then there was the visit to the Glyndebourne Opera. It is only in London that at 3 o'clock of an afternoon, nearly 1 000 people all togged up in dress suits and long dresses and carrying packets of sandwiches for supper could arrive at a station to catch a train, and not even cause a stir of interest or a raised eyebrow! This is the way we travelled 60 miles to the opera from London. Surely there can be no more picturesque or romantic a setting for an opera than this large 400-year old red brick manor house nestling in the green valleys of the unspoilt Sussex countryside. It was a glorious evening and though we returned somewhat late and tired, not one of us would have missed this experience. After the first week in London there was a choice of tours of one week to London and the Home Counties, Cornwall, a Geological tour to Scotland, South Wales, and North England. These were followed by further one week tours to Yorkshire and Lancashire, Scotland, West Country and Midlands, a Geological tour of Wales, and a Mining and Geological tour to Jurassic Iron Mines. We then returned to London for the final session and closing banquet. Post-congress tours were arranged to Europe and to Ireland. It was a wonderful Congress, a great experience, we made many friends and may there be many more congresses! . L. W. P. van den Bosch (Member): Much has already been said in appreciation of the excellent organisation and arrangements made for the delegates who attended this Congress. This report is confined to a brief discussion of the personal impressions gained from the papers presented and the technical visits attended. The papers covered a wide variety of subjects ranging from highly theoretical observations to practical descriptions of operations. There were three main themes, VIZ: 1. The attention given to research and its forceful application to practical operation. 2. A steady development in mechanization and automation leading to savings in manpower. 3. Improvization, modernization and adaptation of exisitng facilities. Thoughts on these themes can best be illustrated by comments on some of the industries visited. COAL The National Coal Board (N.C.B.) has been most progressive and all of us have heard of the Bevercotes Colliery with its completely automatic mining and coal handling equipment. This was not, unfortunately, on show but there is no doubt that this is one of the greatest advances in coal mining leading towards continuous production. Coal in Britain is fighting for its life against oil, North Sea gas, imported gases and nuclear power. Output is dropping, the less efficient collieries are closing down and efficiencies are steadily rising as the following tabulation indicates: In 1931: 1 million men produced 300 million tons of coal In 1947: 0.7 million men produced 230 million tons of coal In 1968: 0.4 million men produced 160 million tons of coal

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

By M. I. Brittan

Discussion Dr R. E. Robinson (Fellow): The author must be congratulated on a very meticulous and self-contained piece of work. It is indeed a pleasure to read a paper that is so clearly and systematically laid out, and where the conclusions and the testwork conducted have been so clearly described. The paper is complete in itself, which makes it very difficult for someone who is not intimately involved in the whole Torco project to make any comments on its content. However, two points that, strictly speaking, fall outside the scope of the paper are of considerable interest. The first relates to the particle size of the material treated. In the paper, the testwork is confined to one standard particle size (minus 60 plus 100 mesh). The essential feature of the paper is to indicate that the rate-controlling reaction in the whole segregation process is the rate of reaction of the ore particles with the reducing agent and the hydrogen chloride. One wonders, therefore, to what extent this relatively slow rate of reaction is affected by the particle size of the ore itself. One imagines that the reaction must take place by contact of the hydrogen chloride with the surface of the mineral particles, and it is reasonable to suspect that the rate of diffusion of the copper ions to the surface is a relatively slow process and is thus the limiting factor in this particular rate of reaction. It is possible, for example, that the improvement obtained, when the ore is subjected to reducing conditions before the chlorination, is due to a breakdown in the crystal structure of the original particle. This breakdown is brought about by the reduction and by the consequent increase in surface area available for reaction with hydrogen chloride. Can the author indicate whether any work has been done along these lines, and whether it has been established that the reaction depends on the surface area available? The second point relates to the application of this kinetic study to the actual operation of a Torco reactor. It was once planned to feed the sodium chloride, together with the reducing agent, into the top of the segregation chamber. In the paper, the author mentions that it has now been established that the segregation chamber behaves, to all intents and purposes, as a fluidized bed, and that there is, therefore, a rapid evolution of gas in the lower regions of the chamber, which, it is imagined, displaces the gas phase rapidly. Since the reaction between sodium chloride, water vapour, and the aluminium silicates in the ore is extremely rapid, one wonders how much of the hydrogen chloride produced is removed from the reaction zone before it has had time to react with the copper minerals. The extremely low consumption of sodium chloride (which is a vital feature of the Torco process) must depend on an extremely rapid circulation of the hydrogen chloride gas to all the ore particles in the segregation chamber. One wonders, therefore, if a system for the introduction of the sodium chloride into the bottom regions of the chamber might not result in even greater efficiency in the utilization of sodium chloride. ProC D. D. Howat (Fellow): All of us who have been concerned with the study of chemical reactions at high temperatures are keenly interested in kinetics and are well aware that this is not an easy study experimentally. Dr. Brittan is to be congratulated on the development of neat experimental methods and for his full discussion of the results obtained. Although the segregation process for the extraction of copper from oxide and silicate ores has been known for almost fifty years, the fundamental chemical and physical changes involved have been little understood and the fundamental data are very scanty. The work now in progress at A.A.R.L., together with that sponsored by the Anglo American Corporation in other research institutions throughout the world, is bound to produce new fundamental data and a much more complete understanding of this rather fascinating process. It is already apparent that some of the old and well-worn chemical reactions that were postulated to occur, just cannot take place in the way which was formerly accepted. Dr Brittan's work, carefully conducted and thoroughly analyzed as it has been, still leaves us with one great outstanding problem. The thermodynamic data and the possible reactions set out in Table I (page 281) of his paper leave us asking, in complete despair, how can copper be converted into a volatile chloride in the presence of HCl, CO and carbon at temperatures about 800°C? The thermodynamics all combine to show that copper should be reduced to metal as the first step in the process. This brings us right up against the second problem. If copper were reduced to the metal how would HCI convert it to the volatile chloride? On top of these problems is the unknown reason for the very high speed of reaction between CO, HCI and the ground copper ore. Still further into the region of the unknown is the reaction by which gaseous hydrochloric acid is produced in the actual process. Perhaps Dr Brittan is feeling grateful that he doesn't have to try to explain this reaction-at this stage of the research programme at least. The results very clearly show that both CO and HCl gas are essential for rapid production of the volatile copper chloride. Dr Brittan states that 18 minutes were required to attain 83 per cent extraction with HCl gas alone and this was reduced to 4 minutes when CO was

Jan 2, 1970

A Seminar to discuss 'Reactivity of Line in Steel Making' was held in the auditorium of Iscor's Headquarters Building in Pretoria on the 5th August, 1971. The Institute organised this Seminar on the occasion of the visit of Dr Obst of the Rheinische Kalkstein Werke GMBH, Wuelfrath, West Germany. The latter is one of the largest lime companies in the world and Dr Obst is in charge of their research laboratory. He and his co-workers have earned a reputation for their research into reactivity of lime in steel making. This work is also of great importance to the steel industry in this country, particularly with the changes which are occurring with the introduction of basic oxygen furnaces. Some 80 persons representing most of the major steel companies attended this Seminar. Dr Obst presented his most interesting paper which he illustrated with projector slides. This paper is printed in full in this journal. This was followed by several contributions and active discussions. The first contribution was made by Dr T. B. Beeton of the Research and Development Department, Iscor. He gave a brief summary of the studies on reactive lime carried out at Iscor since 1968. Their work was particularly related to the selection and definition of the various reactivity tests and the correlation of these with plant results. He demonstrated that the DIN methods, particularly the Din (40°) test, gave the best results and reported that good agreement had been reached between Iscor, Highveld and Northern Lime on future test procedures. Mr B. Lowther of The Northern Lime Company then dealt with problems associated with the production of high reactive lime. The rotary kilns at The Northern Lime plant at Lime Acres are particularly suitable for the production of high-reactive lime, because this type of kiln lends itself to accurate control of temperatures and retention times. Several problems, however, exist. Because of the long haul distances and the deterioration of reactive lime by absorption of CO2 and water, high reactive lime is not suitable for most customers. To constantly be changing kiln conditions to produce relatively small quantities of high-reactive lime, therefore, causes problems. Highveld Steel at present is the only company requiring high-reactive lime and a satisfactory product is now being produced at a cost because kiln capacity is reduced and fuel costs are higher. Dr P. R. Jochens, of the National Institute for Metallurgy then submitted data to show how the reactivity of soft burnt reactive lime deteriorated due to long railage hauls. Detailed sampling of trucks had been carried out leaving the lime works and on receipt at Highveld and it was demonstrated that there was deterioration in the top layers of the truck. This top layer protected the balance of the lime which is still in good condition on arrival at Highveld. Exposure to atmosphere by further handling and storage into the bunkers at Highveld, however, resulted in further severe deterioration in the lime reactivity and the lime when finally fed to the Basic Oxygen Furnace is reduced to one third to one quarter of the original reactivity value. The same deterioration does not occur with normal run of kiln lime, which is burnt harder, but still has a satisfactory reactivity for most purposes. Mr A. A. Hejja of the Department of Metallurgy, Witwatersrand University then made a contribution on the metallurgical aspects of the use of lime of different reactivities in the Basic Oxygen Furnace and the effect on desulphurization efficiencies. He gave a wealth of data on actual tests which had been carried out and came up with the surprising conclusion that the deterioration of high-reactive lime due to transport did not have as serious an effect on the efficiency of desulphurization as one would have expected. The efficiency was good provided high-reactive lime in the first instance had been produced, irrespective of whether it had deteriorated thereafter. Poor efficiency was obtained only when the lime in the first instance was produced in an unreactive form. The temperature rise in the Basic Oxygen Furnace also has a definite effect. If lime is introduced when the temperature is too high, soft burnt reactive lime becomes hard burnt and unreactive before it can dissolve in the slag. Use of ferromanganese slag assists dissolution of lime. There was a great deal of discussion following these contributions. Particular interest was expres8ed in the special lime described by Dr Obst. This consists of a mixture of fine lime which is premixed with fluxes and either briquetted or pelletised. The question of injecting finely ground lime as an alternative was also discussed. Both these systems eliminate the necessity for highly reactive lime. With smaller lime particles, larger surfaces are exposed thereby ensuring more rapid dissolution in the molten slag. The discussions generally were lively and informative and all present derived benefit from learning of the experiences of others. The valuable contribution made by our German visitor, Dr Obst, was particularly appreciated. The instantaneous English-German translation service which was provided, greatly facilitated discussions.

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

By G. Chambovet

Applied geophysical methods such as the surface seismic method have been applied for many years and in many places, mainly for oil exploration and to a lesser extent for mineral deposits? exploration in sedimentary basins. The seismic method fundamental is based on the variations of acoustic impedance in a layered earth model and such variations at each main geological interface create reflected waves that are processed and imaged in order to output a clear picture of the subsurface structure. The geology of South Africa was historically, and even until recently, considered as unfit for seismic exploration and the mines were always reluctant to spend any portions of their exploration budgets on these techniques. Hard rocks and high P-waves velocities were creating quite a hopeless model for any mine geologist or geophysicist (if any), unsuitable for the proper use of seismic waves to image their subsurface problems. Boreholes were considered the only reliable tool to derive a geological image of the mine structural features and were linked sometimes with surface methods such as aero-magnetism. The obvious flaw of this methodology was the inability to derive a continuous image from a discrete set of measurement points. Surface 3D seismic is the tool that gives a reliable solution from the initial model extracted from the boreholes, as even the aero-magnetism mapping gives a flat image, unable to show any depth correlation from well to well. The first 3D surface seismic surveys were recorded in the early Nineties only for the gold mines of the Witwatersrand, after a series of serious new shaft sinking failures. The wrong geological locations of these shafts resulted in financial loss of several hundred million rands. The era of3D seismic just started in South Africa and till 1997, all seismic done in the country was for gold exploration with geological target depths close to the oil exploration average depth of investigation. A very important breakthrough was reached when the depth accuracy of the seismic image was tested in real scale as the stopes were surveyed. An error of amplitude of 20 m was usual when true depth was compared with the seismic image predicted depth and shape. This accuracy, completely unknown in oil exploration, started to gain supporters of seismic methods in the mining community but the cash problems and the concentration/disappearance of gold mines in the late Nineties, led to the belief that seismic would be just a very short exploration activity for the mining sector. ort exploration activity for the mining sector. But starting in 1998 with Impala, a tremendous and continuous 3D surface seismic activity occurred in the platinum mining sector. The seismic world got used to new terms such a Merensky and UG2, which have replaced the VCR and black reef. If the primary expectation of platinum surface 3D seismic was to determine and ascertain new shaft locations, as for the gold mines, the quality of seismic data led the mine geologists to require smaller and smaller imaging of geological objects. In addition to the main structural image, small faults, potholes, and shear zone were common expectations of platinum seismic. In a constant velocity environment, what saved the day was the sharp density contrast between the PGM reef and the embedding geology. A good contrast of impedance exists in the whole Bushveld and is sufficient to have enough reflected waves from the PGM main layers to build a high quality seismic image of the subsurface. Recent advances in technology have led in less than 10years to major improvements in the seismic acquisition by using high frequency vibrating seismic sources, but also in processing and interpretation. With these latest improvements, seismic can detect objects of 7.5 m size, either fault throws, flexures, etc. The PGM formations of the Eastern limb of the Bushveld Complex are now accessible for seismic imaging, with cost per square kilometre comparable to the borehole cost of the same surface unit. The economically acceptable seismic surveys can be used for UG2 structural imaging up to a depth of 210 m below surface. Linked with borehole information, 3D seismic today offers a wide range of information for mine development: structural imaging, small fault detection, pothole and shear zone identification. All users of 3D seismic have also used this technique as a tool in the process to qualify their mineral reserves and especially from the category ?inferred? to the category ?measured?. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. The current high demand on platinum, pushes the seismic towards new technologies to be implemented in order to improve the final image. Using surface and borehole seismic together or acquiring seismic surveys with multi-component receivers have been just introduced in South Africa. In less than 10 years, surface seismic by adapting its methods to the special case of the Bushveld, became a mandatory step in mine development and ore resources evaluation. As part of the ?seismic? world we are proud to be a major player the ?surge? of platinum exploration and production in these last years and we will certainly increase our synergy with the mine sectors in the exciting coming years.

Jan 1, 2006

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By L. Bloch

Most mine safety initiatives in South Africa are doomed to limited success because of one simple fact: they are a-historical and un-cultural and do not deal with the serious ?legacy issues? that still negatively impact on safety, production, and relationships. We in the SA mining industry continually use imported, foreign safety concepts and systems that will not work fully in a South African context. ?The 4th Wave: Culture-Based Behavioural Safety?, as developed by Lance Bloch, an international award-winning clinical psychologist with 12 years? experience in the mining industry - focused mostly on Platinum - is making waves. He has been very successful in creating people-centred, empowered, high-performance safety cultures wherever he has worked. Not only does the 4th Wave transform the corporate culture of a mine, improving safety and production and building an environment of Ubuntu, but it also uses people?s cultures as a means of winning hearts and minds in the battle for safe production. Powerful relationships are built through engagement at all levels, leading to all being focused on the best needs of the company and its constituents as a whole. The programmes are no less than nation-building - something most necessary in the industry, with the pressures from community, unions, the DMR, and politicians. This presentation will describe and discuss the 4th Wave as an advance on previous safety technology and programmes, as particularly relevant to platinum mining in South Africa today.

Jan 1, 2012

By K. A. Moxham

The ARM 1100 was described in a paper presented at the 6th International Symposium on Mine Mechanization and Automation in September 2001. It started operation underground at Rowland Shaft in early 2002. This paper covers the results of those trials that resulted in more than 1 100square metres of UG2 being mined.

Jan 1, 2004

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

By I. V. Filippova, Y. Foucaud, M. Badawi, O. Barrès, L. O. Filippov, S. Lebègue

Sodium silicate (Na2SiO3) is one of the most common reagents used in the froth flotation process, in which it is an efficient dispersant as well as a powerful gangue minerals depressant. Due to its high affinity with a lot of minerals, mostly silicates, it adsorbs on their surfaces and prevents the adsorption of the collectors, maintaining them hydrophilic. Hence, Na2SiO3 is widely used in the flotation separation of rare earth minerals, zinc minerals, iron minerals, scheelite, fluorite, apatite, and many other minerals. For decades, authors have demonstrated higher efficiency of Na2SiO3 when it is used in combination with sodium carbonate (Na2CO3), a common pH regulator. Among many well-known depressants, this system presented the best efficiency for many ores, including the Tabuaço scheelitebearing skarn studied herein. However, the mechanisms resulting in these strong positive synergistic effects are not well understood at the moment. Hence, the response surface methodology (RSM) was applied to this ore, considered as a case study, to optimize the depressing conditions and to study deeply the flotation behavior of this system. Strong synergistic effects between the two reagents were exhibited by the RSM, mostly affecting the scheelite, fluorite, and calcium-bearing silicates recoveries. This was attributed to surface carbonation of the minerals by Na2CO3, subsequently leading to a better depression by Na2SiO3. Overall, a 1:1 ratio between the two reagents displayed the best results in terms of WO3 grade and recovery. To gain understanding in the molecular mechanisms responsible for the aforementioned synergistic effects, FTIR studies were combined with state-of-the-art molecular modelling (Ab Initio Molecular Dynamics at 300 K) on fluorite, an archetype of calcium minerals. Keywords: Synergistic effects, scheelite, depressants, FTIR, DFT calculations

Jan 1, 2020

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By M. -B. Kime

This study applies attainable region analysis to optimise cobalt recovery from oxidised ores via reductive leaching with sulphur dioxide and sulphuric acid. The attainable region framework enables systematic visualisation of trade-offs between cobalt yield and sulphur dioxide loss, guiding reactor network design beyond conventional mass balance modelling. Experimental column leaching trials, supported by validation runs, were conducted under controlled flow and reagent conditions. Kinetic parameters for cobalt dissolution and sulphur dioxide consumption were used to simulate reactor trajectories and construct attainable region envelopes. To ensure hydrodynamic realism, residence time distribution tests confirmed partial plug flow behaviour with dispersion effects, justifying the use of hybrid reactor models in the attainable region simulations. The results revealed that increasing recirculation ratios improves cobalt yield while reducing sulphur dioxide losses, with attainable efficiencies exceeding 90% cobalt recovery and < 20% sulphur dioxide loss. Importantly, the study proposes practical reactor network configurations for future implementation, including staged percolation columns with intermediate mixing zones, oscillatory flow reactors, and modular fluidised bed systems. These designs offer scalable pathways to translate attainable region-based optimisations into industrial practice. Compared to traditional modelling, attainable region analysis provides a geometric decision support tool that captures multi-objective trade-offs and reactor interactions, offering novel insights for continuous leaching system design. This work advances the application of attainable region methodology in minerals engineering by bridging theoretical optimisation with practical reactor design, supporting sustainable cobalt recovery from both primary ores and recycled feedstocks.

Mar 30, 2026

By Kevin Peacocke

The future of Gravity ? Primary mineral recovery ? Enhancement of existing process efficiency ? Pre-Concentration ? Alternative? or ?New? production

Jan 1, 2006

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014