Search Documents

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By R. C. D. Phillis

The annual mine planning process is one of the most important tactical/operational steps towards achieving strategic goals. These tactical plans are part of a very comprehensive Mineral Resource Management process, with the natural sequel to planning being execution. The execution of an underground hard rock mine plan is a multi-project environment that comprises many development-construction-equipping-stoping single project paths, which are referred to as ?stoping paths?. The uncertainty that typifies execution of projects comes in the form of untimely disruptions to constituent tasks and/or project paths. Annual mining plans also include quantified objectives for occupational health and safety, production, quality, cost, employee morale, environment, and corporate social investment. Such objectives make for a highly complex environment that management must contend with?complex in the sense that all the paths and objectives have interdependent constraints. Furthermore, at the time of this paper, Sections54*and 55**of the MHSA*** put the onus on management to ensure legislative adherence. It stands to reason that planning estimates allow excess capacity?buffers?that cushions the impact of untimely disruptions. This paper concerns the fact that despite all the buffers allowed for, time, scope, and budget creeps impact on mine planning and threaten its successful execution. As a consequence, the paper deals with buffer management, the essence of Critical Chain Project Management (CCPM). Effective buffer management provided strategic (executive level) updates without losing the tactical/operational detail necessary for job card creation, especially where professional skills and experience are in short supply. Indicative bottom-line results showed CCPM to be highly effective.

Jan 1, 2011

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By A. A. Angelov

This paper presents a unique method of monitoring the effectiveness of the planning process as well as the execution of mine plans. The method primarily determines the degree of deviation from the original mine plans by comparing actual mined areas to initially planned mining areas. The performance of mining operations is also measured by comparing actual and planned tonnages for a particular period. Once the degree of deviation from mine plans has been established the cause/s of the deviation can be determined through a simple fault tree analysis. Accurate identification of the reasons of deviation can aid the mine in selecting possible methods to correct the deviation. It is, however, beyond the scope of this paper to discuss the methods employed in correcting such deviations, as each mining operation will have unique causes of plan deviation and methods of remedying them. Deviations from the plan greatly affect the yields obtainable, which in turn affects the life of mine, thus having negative economic and financial implications. Accordingly, this paper presents a project management method which aims to reduce risk by improving planning systems to ensure optimum overall extraction of coal reserves.

Jan 1, 2010

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By S. Ganguly

Slag samples taken from adjacent to the furnace wall of a submerged arc ferromanganese smelting furnace have been found to contain high concentrations of K2O. To characterize the phase equilibria relevant to these slags experimental studies have been carried out to determine pseudo-ternary sections of the form ?MnO?-CaO-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.65 and 6.0 wt% K2O for temperatures in the range 1523-1673 K. In the pseudo-ternary section investigated the primary phase fields are found to be mullite, 3Al2O3?2SiO2; corundum, Al2O3; spinel, MnO?Al2O3; manganosite solid solution, (Mn,Ca)O; dicalcium silicate,2CaO?SiO2; gehlenite 2CaO?Al2O3?SiO2; anorthite CaO?Al2O3?2SiO2; kalsilite KAlSiO4 and leuciteKAlSi2O6. It was found that the presence of K2O in the slag decreases liquidus temperature in the anorthite and gehlenite primary phase fields. The manganosite primary phase field is expanded in the direction of increased (Al2O3+SiO2) and the liquidus temperatures in the manganosite primary phase field are increased significantly with the presence of K2O in the slag.

Jan 1, 2007

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001