Search Documents

By M. Z. Emad, M. U. Khan, A. ur Rehman

The use of stemming plugs in surface blasting is gaining popularity because of the environmental, technical, and economic advantages. Although previous studies have established the operational effectiveness of different types of stemming plugs, evaluations of the economic and ergonomic impacts are lacking, thereby hindering their application in many mining operations. Consequently, a significant proportion of mining operations end up performing less efficient blasts. We evaluated the effectiveness of three types of stemming plugs by conducting multiple full-scale production blasts. The results show that stemming plugs reduce the need for secondary blasting and increase blast performance. An economicanalysis showed that the incorporation of stemming plugs can reduce blasting costs significantly.

Jul 1, 2021

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By Thomas V. Fame, William E. Porter

"As geological and mining conditions become more complex, and as overall mining economics become more marginal, short- and long-range decision-making regarding multiple-seam surface mining becomes more difficult. The decision-making problem involves a study of economics, cut-off grades and ratios, equipment capabilities, sequencing and selective mining practices.This paper is concerned primarily with multiple-seam mining of bituminous coal. The research has led to the development of an economic decision-making model for use as a day-to-day tool to aid mine operators and pit geologists to decide what and how to mine.The model is designed as an aid for feasibility decision-making in multiple-scam situations and for situations where selective mining is needed or desired. In effect, a simulation of the feasibility and preliminary mine planning phases has been developed. The model is divided into four separate segments: decision-making, simulated mining, cost calculations and the determination of the discounted cash flow return on investment."

Jan 1, 2014

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By R. J. Hundermark, L. R. Nelson

The critical importance of tap-hole design and management to furnace performance and longevity is explored through examining some of the specific matte, metal and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloys smelting and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally core aspects of tap-hole equipment and maintenance are identified that are considered important to securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance.

Jan 1, 2014

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By R. Nyirenda, B. Besa, N. Dzimunya

The accurate estimation of peak particle velocity (PPV) is crucial during the design of bench blasting operations in open pit mines, since the vibrations caused by blasting can significantly affect the integrity of nearby buildings and other structures. Conventional models used to predict blast-induced vibrations are not capable of capturing nonlinear relationships between the different blasting-related parameters. Soft computing techniques, i.e., techniques that are founded on the principles of artificial intelligence, effectively model these complexities. In this paper, we use the random forest (RF) algorithm to develop a model to predict blast-induced ground vibrations from bench blasting using 48 data records. The model was trained and tested using WEKA datamining software. To build this model, a feature selection process using several combinations of Attribute Evaluators and Search Methods under the WEKA Select Attributes tab was performed. The correlation coefficient of the actual data and RF model-predicted data was 0.95, and the weighted average of the relative absolute error (RAE) was 10.9%. The RF model performance was also compared to the equivalent-path-based (EPB) equation on the testing data-set, and it was seen that the RF model can effectively be used to predict PPV. The study also demonstrates that the EPB equation is a suitable empirical method for predicting PPV.

Mar 30, 2023

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

By K McLeod

{Figure 1} The Placer Dome-Western Areas Joint Venture?s South Deep Twin Shaft Complex, has been planned and dreamt of for nearly 20 years. [ ] The gold reserve at the bottom of these shafts is one of the largest single intact gold deposits remaining in the world today, containing an estimated 57 million ounces. This is about the size of the fictitious reserve created by inventive prospectors for the infamous BREEX scam in Kalimantan about ten years ago and about the size of the reserve Harmony claims as its own in it?s current hostile takeover bid for Gold Fields. So it is certainly of the magnitude that dreams are made of. [ ] {Figure 2} The unique orebody lies in a continuous, highly concentrated, thick deposit, an estimated twelve kilometres along dip and a two kilometre wide strike. Due to the thickness of some sections of the reef, up to 60 metres in places, bulk mining methods will be required for it?s extraction. [ ] {Figure 3} The twin shaft system comprises a main shaft which had an initial design depth of 2765m and a ventilation shaft of 2760m, making them the world?s deepest to be sunk in a single lift. The shafts were

Jan 1, 2005

By M. Mokgohloa, T. R. Stacey

Boring of tunnels and shafts in hard rock under high stress conditions is becoming more common as mines and tunnels are developed at greater depths. Under the high stress conditions, fracturing of the often-brittle rock occurs in the walls, backs, and ahead of advancing faces of excavations. Fracturing can have a significant impact on boring activities: sidewall spalling, which affects machine gripper capacity, and fractures can also develop in the rock ahead of the face, leading to blocky rock conditions, which may have a significant effect on machine excavation. Fracturing may develop dynamically, leading to rock bursts manifesting in the form of strain bursts, which can be hazardous and destructive. In brittle rock, fracturing is commonly extensional in nature. The focus of this paper is on fracturing in the face of the excavation. Examples of such fracturing behaviour are described briefly in the paper. Numerical analyses were carried out to predict the initiation of extension fractures and their orientations ahead of excavation surfaces, and the resulting formation of rock slabs/plates, and the stability of these plates. The results should be beneficial for the evaluation of the conditions prior to, and during boring operations.

Nov 27, 2024

By C. E. More

Some observations on 'ancient' mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board's management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

A wide range of drill holes and process streams are sampled for resource estimation, grade control and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2009