Search Documents

By O. Bazhko, F. D. L. Uahengo, Y. R. S. Hara

Although the conventional acid-reductive leaching method effectively extracts copper (Cu) and cobalt (Co) from Cu–Co oxide ores, efforts to enhance hydrometallurgical performance are ongoing. This study evaluates the influence of sulphuric acid (H2SO4) and sodium metabisulphite (Na2S2O5) on metal extraction from Zebesha Cu–Co oxide ore using ferrous sulphate heptahydrate (FeSO4·7H2O) and ferric sulphate (Fe2(SO4)3) as lixiviants. Ore samples (<150 μm) were leached at ambient temperature for two hours, and metal concentrations were determined via X-ray fluorescence analysis. In the FeSO4·7H2O system, Co, Mn, and Ni recoveries increased w=ith Na2S2O5 concentration, reaching a maximum of approximately 80% Co at 150 kg/t, while Cu recovery remained below 5%. Conversely, with Fe2(SO4)3, Cu recovery peaked at 88% at 50 kg/t Na2S2O5, then declined to 79% at 150 kg/t. The addition of H2SO4 improved metal recoveries in both systems. Notably, 60 kg/t H2SO4 yielded 92% Cu extraction in Fe2(SO4)3, while Co, Ni, and Mn remained below 40%. However, in FeSO4·7H2O, Co recovery improved from 40% to 84%. These findings suggest Na2S2O5 is more effective for cobalt extraction with FeSO4·7H2O, whereas H2SO4 enhances copper extraction in Fe2(SO4)3.

Oct 24, 2025

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By Patrick J. Foster

This paper summarises a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialled at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

Mr D. Wilson was born in Vereeniging, where he also completed his schooling, matriculating from General Smuts High School in 1977. Mr K.A. van Gessel was born in 1937. His final studies were conducted at Delft University, where he graduated with an M.Sc. degree in mining engineering. Mr J.G. McCaUum was born in 1938 and matriculated at Jeppe Boys&apos; High School, Johannesburg. Mr H. Scot RusseU started his mining career at Randfontein Estates Gold Mining Co. Witwatersrand, Limited, where he served as temporary Geological Assistant, Sampler, Surveyor, Shift Boss, and Mine Overseer. Mr A.M.P. Henderson was born in 1950, in Kiel, West Germany. Mr J.L. Nel matriculated in 1957. This was folowed by his atainment ofthe folowing degrees: B.Sc. (Chemistry, Physics) in 1961, B.Sc. Hons. (Metalurgy) in 1965, M.Sc. (Metalurgy) in 1967, and MDD (student of the year) in 1981

Jan 1, 1989

By D. J. Adams, W. K. Rymon-Lipinski

Rock engineering plays a crucial role in contributing to sustainable development in South African mining. A framework for this has been created through legislation and structures to encourage the mining industry to have a long and prosperous future. However, rock engineering input is an essential element to achieving success. The most accessible deposits have been mined in South Africa and although large reserves still remain, many of these are difficult to access and will require excellent rock engineering knowledge and skill in the future. This is borne out by the fact that more than 50 % of fatal accidents are related to rock engineering issues. Many of these may be addressed with rock engineering solutions which are not beyond current rock engineering technology. A reduction in fatalities and injuries contributes to a sustainable mining industry.

Jan 1, 2003

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article thefollowing hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the of chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

Professor R.P. King holds a Ph.D. degree in chemical engineering, which he obtained at the University of Manchester in 1963. After that he lectured in the Departments of Chemical Engineering at the Universities of the Witwatersrand and Natal. From 1968 to 1973, he was Leader of the Chemical Engineering Research Group of the National Institute for Metallurgy at the latter University. Mr C.E. Fivaz, Pr. Eng., is Chief Consulting Metallurgist of Rand Mines (Mining & Services) Limited, and is responsible for the metallurgical activities of the Gold and Uranium Division and the Coal and Base Minerals Division of the Group.

Jan 1, 1984

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more &apos;models&apos; available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of &apos;international standards&apos; we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry&apos;s best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By M. Yavuz

Two different methods of fuzzy multiple criteria decision making have been proposed to solve the problem of mining method selection in the paper titled ?Mining method selection by multiple criteria decision making tool, by Bitarafan and Ataei. This problem is really important and also difficult to solve because of the need of handling many criteria simultaneously in the process of decision making. Bitarafan and Ataei have selected 15 criteria for the case study in their paper and those criteria have not been clustered/grouped yet. The number of selected criteria is only 15, although there are more criteria that should be handled in a real case, because they have used Saaty?s method in the section ?Fuzzy multiple attribute decision making? in their paper. Saaty?s method considers the pair wise comparison of criteria and uses random indexed which have already been derived and published. Available random indexes, however, have been derived for maximum 15 criteria so far.

Jan 1, 2007

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

Keywords: Pyrometallurgy, Wits University, research Wits Metallurgy celebrated its centenary in 2004. The department has been at the forefront of education and research and has contributed greatly to the metals and minerals industry, both in South Africa and abroad, in terms of human resources and knowledge generation. A significant number of industry and academic leaders worldwide are Wits Metallurgy graduates. Since its early beginnings, pyrometallurgy has always been part of the curricula and research offered by the department. Pyrometallurgical activities started to expand tremendously from the middle of the 1960s, especially by the formation - together with Mintek - of the Pyrometallurgy Research Group, which continues its internationally recognised research activities today. The research efforts have been concentrated on problems associated particularly with ferroalloy, steel, stainless steel production, and PGM/Cu-Ni sulphide smelting. In recent years, research has been further expanded to physical modelling of pyrometallurgical reactors. Almost all of the specific research projects were handled from a fundamental point of view, and hence a large number of MSc(Eng) and PhD degrees were achieved by candidates under the supervision of the Pyrometallurgy Research Leaders. Moreover, a significant portion of the research results were published in internationally recognized journals and conference proceedings. Among these, Infacon and the Molten Slags, Fluxes and Salts Conference series are worth mentioning. The studies from a fundamental point of view include thermodynamics, phase equilibria, transport phenomena, kinetics, and process dynamic aspects of high temperature processes and systems, both in the solid and liquid states.

Jan 1, 2006

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

[Dr. N.A. Barcza (Chairman) Mr. R.J. Linnell (Vice Chairman) Mr. J. Basson Dr. L.A. Cramer Mr. W.A. Gericke Dr. N.C. Machingawuta Mr. C.S. Mahony Dr. L.R. Nelson Mr. D. St J. Slater Mr. B.J. van der Walt INFACON X TECHNICAL PROGRAMME COMMITTEE Dr. L.R. Nelson (Chairman) Mr. W.A. Gericke (Vice Chairman) Mr. W. Barrett Mr. T.R. Curr Dr. O.F.R.A. Damm Prof. R.H. Eric Mr A.M. Hearn Mr. A.R. Jamieson Dr. N.C. Machingawuta Mrs. L. Mthombeni Mr. F.X. Prins Mr. J. van Tonder ]

Jan 1, 2004

By C. G. Anderson

Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.

Jan 1, 2008

By D. Nyembe, B. Mamba, Antoine F. Mulaba-Bafubiandi

Copper and cobalt are generally electro-won from their aqueous sulphate solutions. After optimised leaching of their ores, concentrates or calcine bearing minerals, the leachate is clarified and suitably purified prior to the electrolytic extraction of the metal of pursuit (Pearcy, 2006). Solvent extraction (SX) using appropriate organic solvents and ion exchange (IX) with relevant resins are known purification processes used for copper and cobalt recovery (Stanely, 1970).As zeolites in general and natural zeolites in particular, demonstrate ion exchange properties (Korkuna et al., 2005), an attempt has been made to use Southern African natural clinoptilolite in the recovery of copper and cobalt from their aqueous sulphate solutions. Initially, synthetic Co and Cu solutions were prepared. Preceded by laboratory ore leachate, plant solutions are to be used. AAS, XRF, XRD, Mossbauer spectroscopy and BET were characterization techniques used. Natural clinoptilolite was used as-received as well as acid activated; and cobalt and copper extractions were performed at room temperature.

Jan 1, 2007

By PC Pistorius, DR Groot

The South African base metals industry has been one mainly focused on the production of metals or metal compounds from primary ores. This is true for metals such as titanium, vanadium, chrome, manganese, cobalt, nickel, copper, zinc and aluminium. The steel making industry has traditionally used a substantial portion of scrap steel, and could thus be considered to be somewhat of an exception. Secondary sources have played much less of a role, possibly due to at least some of the following factors. Scrap material is often of unknown composition, and thus it requires additional chemical analysis, and possibly special treatment. Tonnages are relatively small, and the incorporation of secondary materials is possibly seen to carry undue risk and inadequate benefit. South African consumers are still not very conservation and recycling conscious, which limits the amount of scrap made available. This attitude might also be expected to influence decision makers in these industries. Finally, pressure from environmentally motivated activists locally has not been unduly large. This landscape has been changing, and is continuing to do so. Various municipal authorities such as those of Pretoria, Johannesburg and Cape Town are reporting increasingly limited landspace for waste (Bondolfi, 2007). There are increasing concerns regarding the leaching of hazardous metals such as chromium, mercury and cadmium from landfill waste, especially electronic and electric wastes ? the so-called eWastes. In more developed countries such as the United States of America and Western Europe the problem of eWaste has grown to the extent where legislation has been enacted, such as the Waste Electrical and Electronic Equipment (WEEE) legislation of the EU (European Union Directive 2002/96/EC). The 19th and 20th centuries have seen major technological advances. Relevant to this paper is the availability of centrally generated electrical power, telecommunication, entertainment through recorded and transmitted music and images, the growth and pervasive influence of electronics, and the handling of digital data by computers and microprocessors. These developments have placed ever increasing demands on resources for the manufacture of electrical and electronic equipment, as well as on the generation of electrical power. Most of the resources required are non-renewable: copper, steel, aluminium and other metals, various thermoplastic polymers such as PVC (polyvinyl chloride), polyethylene and ABS ( acrylonitrile-butadiene-styrene), thermosetting polymers such as epoxies, elastomers such as butyl rubber, glasses and ceramics, and composites such as fibre reinforced plastic (fibreglass). The conservation of non-renewable resources inevitably includes recycling. To a certain extent, recycling of materials locally is well established. Thus glass, paper, used oil, car batteries, ferrous scrap such as beverage cans and non-ferrous scrap such as

Jan 1, 2007