Search Documents

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003

By S. Badr, R. Mendoza, M. U. Ozbay, M. D. G. Salamon

ABSTRACT: The use of coal pillars at depth is fraught with problems due roof control difficulties and the possible occurrence of coal or pillar bumps. In the USA the largest and most important application of pillars at depth is in longwalling, where chain pillars are the customary supports of the multiple entry developments. At first, the chain pillars were designed using conventional approaches, where the principle is that the strength of the pillar should exceed the load imposed on it. Such approach to design led to larger and larger pillars at great depths, but instead of eliminating, it tended to aggravate the roof control problems. Eventually the idea was born that small sized yielding pillars, which have proved to be successful elsewhere, might provide the answer to this pressing problem as well. The aim of this paper is to study the modes of pillar failure at great depths, using two solution methods. The first of these comprises some elementary solutions obtained with the aid of a simplified conceptualization of the rock mass. This model consists of a strain-softening coal seam sandwiched between two stratified masses. The second approach utilizes FLAC3D, which is a commercially available three-dimensional numerical modeling software package. To gain a better insight, both the strain-softening and ideally plastic Mohr-Coulomb constitutive laws embodied in FLAC3D were exploited. As expected, the width to height ratio of the pillar has proved to be the primary factor that determined the behavior of the pillars. Narrow pillars fail in a stable manner without the occurrence of instabilities. Intermediate w/h ratio pillars under the appropriate loading conditions, may fail suddenly and may even collapse totally. Squat pillars do show the potential for sudden, coal bump like side failure, but because the remaining large width of the inner core, the ruble around the pillar provides sufficient confinement so as to reestablish stability. Finally, the study revealed that the traditional Mohr-Coulomb law does not provide a useful insight into the failure of coal pillars. RESUME: L’utilisation des piliers de charbon dans les mines souterraines de grande profondeur occasionne des problèmes due aux difficultés de control de plafond et possibles fracture ou explosions au niveau des piliers. Aux Etats-Unies d’Amérique, l’utilisation des piliers dans les mines souterraines de charbon comme moyen de support est considèrees comme étant la plus grande et la plus importantes des méthodes utilisée dans le ‘’ longwalling method’’ ou une série des piliers sont disposé de manière à supporter les multiple entrées d’exploitation de charbon. En premier lieu, cette série des piliers étaient construit de manière conventionnelle avec un principe basé sur le fait que le poids exerce sur les piliers doit être inférieur a la force que ces piliers exerce sur le plafond. Ce principe a conduit a ce que le volume des piliers augmente au fur et à mesure que la profondeur au de la mine augmente. Malheureusement, au lieu de résoudre le problème de support, ce principe n’a fait qu’aggraver le problème de contrôle de plafond. Eventuellement une idée s’est dégagé allant du fait que les piliers endommagés de taille moyenne qui se sont avérés être efficaces ailleurs, pourraient fournir un indice à ce particulier problème. Le but de cette recherche est celui d’étudier les différent types de ruptures qu’un pilier peut occasionner lorsqu’il est utilisé a grande profondeur, tout en utilisant deux possible méthodes. La première d’entre elle comprend quelques solutions élémentaires obtenues avec l’aide d’une méthode simplifié et conceptuelle de la masse de la roche. Ce modèle consiste à prendre en sandwich la bande de minerais de charbon entre deux masses stratigraphiques sans pour autant endommager le plafond. La seconde méthode nécessite l’utilisation du ‘’ FLAC3D’’, qui est un logiciel commercialisé disposant d’un modèle numérique en 3 dimensions. Dans le but d’obtenir

Jan 1, 2003

By H. Immink

Keywords: Kyoto Protocol, carbon credits, global warming, energy, auditing Climate change is nowadays being taken increasingly seriously, and the link between global warming and the carbon dioxide released in the generation of energy is coming under increasing scrutiny. The Kyoto Protocol was signed in 1997, after five years of negotiation. So far, about 84 countries have ratified this agreement, under which terms developed countries have strict targets linked to their 1990 level of emissions. However, ?greenhouse gas? (such as carbon dioxide) emissions continue to rise alarmingly. According to the World Resources Institute, greenhouse gas emissions in the USA increased 13% from 1990-2002, while Australia recorded a 22% increase. In contrast, the European Union, a Kyoto signatory, has seen a small decline in its emissions during the same period. This is led by the UK and Germany, who reduced their emissions by 15% and 19% respectively. The concept of ?carbon credits? provides a funding mechanism for companies in the developed world to compensate for some of their CO2 emissions by paying companies (trading credits) elsewhere in the world to undertake projects to bring about reductions in emissions. In the southern African mining industry, it will be possible to get refunded for undertaking voluntary emission-reduction projects. Concern about the environment is creating business opportunities. A preliminary calculation has shown that various projects in South Africa (those in the pipeline, with quite a high likelihood of coming off) could earn a combined total of about R2.5-billion, under the initial phase of the Kyoto Protocol's carbon-credit scheme, which allows developed-country companies to trade credits with developing countries. A number of local companies are planning projects that could comply with the Clean Development Mechanism (CDM), in which they will implement techniques to achieve certified emission reductions (CERs) of greenhouse gases. In order to prevent abuse of such a system involving vast sums of money, vigorous audits need to be carried out. A company has to prove it has made real changes and is not simply conducting business as usual under a cloak of claimed environmental improvements. PricewaterhouseCoopers has applied to become one of only a few international agencies that will be accredited to conduct validation and verification of the credits, by auditing what is called the ?designated operational entity?. An independent validator needs to confirm that the project meets the strict requirements of the Kyoto Protocol. The company has to demonstrate that it?s not business as usual. So, if you refurbished every five years, the next refurbishment is not a good CDM project, unless you can demonstrate that you will do something beyond the maintenance - that is what can be registered. So, Kyoto intends to get additional projects going, and the money for that is actually quite good - prices of 14 euros per ton of carbon dioxide not emitted have been seen. The price depends on who takes the risk for non-delivery if a project doesn?t deliver the emission reductions on time. The highly energy-intensive South African mining industry is heavily dependent on coal. There should be many opportunities for the pyrometallurgical industry to come up with creative ideas to reduce emissions, and there is now an additional financial incentive to encourage this. Companies can actually get money in return for doing these types of projects, in addition to the contribution to corporate social responsibility.

Jan 1, 2006

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

The environmental impact of solid waste materials is closely linked to their potential to produce a hazardous leachate once deposited in a landfill. This potential is conventionally assessed with simple laboratory batch leach tests, which find more and more frequent application also in the minerals and metals industry. Such tests are intended to help distinguish between high and low risk wastes, but are completely unsuitable to allow quantitative prediction or modelling of the long-term leachate generation potential. In the present approach the leachate generation process is perceived as a combination of bulk convective transport, stagnant zone and inner particle diffusion, as well as reaction kinetic effects. Model equations are formulated accordingly. A modelling frame work, WASTESIM, has been developed at UCT, which allows flexible combination of the model components and simulation of leach scenarios. Quantitative model parameters are obtained from a systematic laboratory study on the waste material in question. The combined assessment and modelling approach is demonstrated with a study on Cr (VI) leaching from a ferro-chromium slag material. Although not straightforward, the approach is particularly useful in determining long-term liabilities in the context of waste disposal sites with considerably more reliability than has previously been possible. Keywords: waste deposits, waste leaching, heap leaching, environmental, risk assessment, Cr (VI), ferro-chromium, slag.

Jan 1, 2000

By P. J. Brereton-Stiles, M. S. Rennie, N. Singh

Ferroalloy producers are large-scale users of electrical energy, which in many countries is in short supply and increasingly expensive. Preheating and/or pre-reduction using natural gas, recycled furnace gas or coal fines have lowered the specific use of electricity, but the high energy concentration necessary for most reduction processes can be achieved only by the use of high electric currents. Most countries have insufficient electricity to supply the demands of industry and the domestic consumer, particularly during certain periods of the day and certain times of the year. The generation and distribution of electricity is a large-scale expensive business, which is financed and managed directly or indirectly by government bodies in most countries. Both economic and political imperatives determine how much electrical energy is made available to whom and at what price. In South Africa demand is set to outstrip supply within the next few years, and the local supplier Eskom has moved from a traditional demand tariff pricing structure to a time-of-use tariff pricing so as to limit peak demand usage. This will mean a substantial increase in electricity cost to those users unable or unwilling to reduce consumption during peak periods. The optimal use of the available electrical energy depends both on the process, the furnace size, the configuration and infrastructure of each plant and its cost structure. As the cost and availability of electricity is set to change dynamically, the management of the situation becomes a real time control and optimisation problem. This paper discusses some the process and operational constraints associated with low- or no-load conditions and how to manage the situation. Electrode management will be one of the key issues.

Jan 1, 2004

By G. H. Lind

Seven full and partial pillar extraction operations were visited in New South Wales, Australia, in the early parts of 2001. Certain factors unique to these operations have led to the general success of the safe and economic extraction of these coal pillars. Some of these factors attributable to the overall success of these operations are discussed in this paper. In particular, geotechnical mapping, specific legislation pertaining to pillar extraction, mining methods, the role of temporary supports and training are described. It is found that some of these factors have useful attributes which could be used to design a methodology for extraction of underground coal pillars in the Witbank and Highveld coalfields of South Africa.

Jan 1, 2002

By SDN Wessels, WA Naismith

On 16 July 2004, at 07:10 a collapse of about 1.8 million m3 (about 4 ½ million tonnes) took place on the north wall on Nchanga Open Pit This collapse was the result of a developing instability that was first identified when the benches in this area were exposed during September 2002. The NOP Geotechnical and Survey Departments closely monitored the development of the failure. Control measures were implemented to reduce risk to men and equipment. These measures were continually improved and adjusted in reaction to observations and changing conditions. The purpose of this paper is to describe in detail the monitoring results that were obtained both by traditional methods and the novel Slope Stability Radar System (SSR). Difficulties encountered in establishing critical deformation levels and deformation rates that can be used to predict the onset of collapse are described. Details of the monitoring and control measures, which led to the successful completion of mining in the area, are also described in this paper.

Jan 1, 2005

By Y. Mitani, F. Vallier, T. Esaki

Shear-flow coupling tests are conducted using an original apparatus, and a shear-flow coupling model using Geographic Information System (GIS) is developed in order to evaluate shear-flow coupling properties of a rock joint. Shear-flow coupling tests indicate that the hydraulic conductivity of joint once decreases, and then rapidly increases at the shear displacement near the peak shear stress. The proposed model simulates the test results relatively well. However it indicates that it is difficult to apply the local ‘cubic law’ model in the initial shear stage, in which the change of selective flow path is remarkable. Scher-Fliess-Kopplungsversuche werden mit einem neuartigen Versuchsgerät durchgeführt und mithilfe von Geo-Informationssystemen (GIS) gedeutet, um so ein Modell für die Scher-Fliess-Kopplung in Gebirgstrennflächen zu entwickeln. Die Versuche zeigen, dass die hydraulische Leitfähigkeit zuerst abnimmt, dann aber schnell wieder zunimmt sobald die maximale Scherfestigkeit erreicht ist. Das vorgestellte Modell bildet die Testergebnisse relativ gut nach. Es zeigt auch, dass es schwierig ist, das lokale Cubic Law im Initialstadium der Scherbeanspruchung anzuwenden, in dem die Variationen selektiver Fliesswege gross ist. Les essaies hydro-mécaniques couplés en cisaillement sont réalisés grâce à un appareil éxperimental prototype et un modèle de couplage hydro-mécanique utilisant le S.I.G (systeme d'information géographique) développé dans le but d'évaluer les propriétés hydro-mécaniques des joint rocheux. Les résultats indiquent que la conductivité hydraulique des joints décroit puis augmente rapidement en se rapprochant du pic de cisaillement. Le modèle proposé simule relativement bien les résultats expérimentaux ; mais indique également qu’il est difficile d’appliquer localement la loi cubique au début du cisaillement où, les changements d’orientation dans le réseau d'écoulement sont considerables.

Jan 1, 2003

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By M. Tangstad, B. Monsen, H. Midtgaard, R. Ishak, M. Syvertsen, I. Solheim

Charcoal is an interesting reducing agent because it is produced from growing wood which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. In the biocarbon project the possibilities for using charcoal is investigated as well as other biological based and renewable reductants for ferroalloy production. The background for the project is that the Norwegian ferroalloy producers wish to contribute to reduction of CO2- emissions. This paper focuses on the use of charcoal instead of coke for the production of manganese alloys, and the consequences of doing so. Results from practical SiMn smelting experiments on a pilot scale have previously been reported, where only 12-14 % Si in the metal was obtained when charcoal was used. Recently we have attained satisfactory 18 %Si also for charcoal, but good results are indeed dependant on good furnace performance. There is no tradition for using charcoal for manganese production in Norway. A change from using mainly coke to the use of some charcoal will demand new routines for furnace operation, raw material and off-gas handling. Hence, characteristic properties of charcoal, which may cause change of furnace operation, have been measured and are compared to coke. The following results are presented: ?Thermal abrasion strength together with CO2- reactivity; important parameters for the performance of the upper part of the furnace. ?Coke-bed resistance; it will increase with the use of charcoal (a review of new results). ?Slag reactivity; a relevant method for testing slag reactivity of industrial reductants is of interest. The suggested method can serve for comparing slag reactivities towards graphite.

Jan 1, 2007

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By M. A. W. Bryson

It is well documented that a significant amount of the new PGM (Platinum Group Minerals) production that is coming on stream now, and over the next few years, is to come from the UG-2 reef. Clearly the reservations, or perhaps the perceived reservations, attached to the processing of this ore are no longer there. What were the metallurgical issues that delayed the exploitation of the PGM values from this reef? Traditional furnaces treating Merensky concentrates were not able to accept the concentrate produced from a UG-2 plant due to the relatively high chromite content of this product. The chromite reports to an insoluble spinel phase that accretes in the furnace, resulting in the necessity to shutdown and dig the furnace out periodically. This was clearly not an attractive economic option, so producers stayed away from it in the early days. The Merensky ore had all higher base metal credits anyway, and you needed them to get a matte fall, so there was no driving force to look seriously at the UG-2 reef. Platinum demand at this time could be easily met from the Merensky ore, so the motivation to tackle more complex ores was not there. The low price of PGMs meant that these operations were not particularly profitable and there was little effort directed at improving the operations. Concentrators were generally not run very efficiently and the emphasis was on cost reduction through increasing milling rates.

Jan 1, 2004

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power inputs over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge, which was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2013

By R. P. Jensen

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM Arbitrary Lagrangian Eulerian (ALE) computational techniques allow treatment of gases, liquids and solids in the same simulation. ALE methods include the ability to treat shock waves in gases, liquids and solids and the interaction of shock waves with each other and with media from one of the other categories. ALE codes can also treat explosive detonation and the expansion of the explosive gases and their interaction with air and solids. ALEGRA is a 3-D ALE code that has been developed at Sandia National Laboratories over the past few years. ALEGRA has been applied to a 2-D simulation of presplitting using decoupled explosives in rock blasting with very interesting results. The detonation of the explosive at the bottom of the hole sends a shock wave up the borehole driven by the explosive gas expanding into air. The explosive gas compresses the air against the stemming column where it rebounds and recompresses at the bottom of the borehole. This type of ringing takes several cycles to damp out. The explosively induced expansion of the borehole is also treated by ALEGRA as well as the shock wave imparted to the rock. The presentation of this paper will include several computer animations to aid in understanding this complex phenomenon.

Jan 1, 2000

Rockbursts continue to be a scourge in the mining industry, being responsible for accidents and damage to mining excavations. Although the problem has been present for more than a century, and although much research has been carried out, a solution is still elusive. Determination of, firstly, the demand on the support system imposed in the rockburst and, secondly, the capacity of the support system, cannot be carried out with any confidence, and therefore rockburst support cannot be designed using a conventional design approach. In contrast with the conventional approach, observations of rockburst damage in a mine have revealed a possible alternative approach to rockburst support ? sacrificial support. It was observed, in rockburst events, that a support system consisting of concrete panels restrained by grouted cables was destroyed, and the concrete panels were ejected. However, the rock behind the panels remained apparently undamaged and in place. This behaviour reignited the concept of sacrificial support, conceived more than 20 years ago, and which is described in this paper. The remedial solution implemented on the mine, involving cables wrapped over the panels and retained by grouting into boreholes, has been subjected to rockburst loading and has confirmed the validity of the sacrificial support concept. The concept of sacrificial support may be controversial, but is deliberately presented here with the aim of generating discussions and contributions, and with the ultimate aim of improving safety and reducing rockburst damage in mines. Keywords rockburst, seismicity, seismic waves, rock support, support design.

Jul 1, 2013

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006