Search Documents

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

By Travis Q. Lyday

Gold continued to dominate mineral production in the group of volcanic islands and atolls of Melanesia in the southern Pacific Ocean, which comprise the British Commonwealth nation of Fiji. The Fijian mineral sector, however, remained of minor importance in terms of export earnings, Government revenues, and employment to the economy of the country, which was primarily agrarian with sugar as its mainstay. The Vatukoula gold-silver mine on the north side of the main island of Viti Levu remained the largest and most important mining operation, as well as Fiji's only operating metalliferous mine. In October, Western Mining Corp. (Fiji) Ltd. (WMCF), a wholly owned subsidiary of Australian-registered Western Mining Corp. Holdings Ltd., increased its interest in the Vatukoula joint venture from 10% to 20% by exercising its option with Emperor Gold Mining Co. Ltd., also of Australia. The assumption of mine management operations at Vatukoula in 1983, with its attendant influx of additional capital and technological expertise, enabled WMCF to increase both efficiency and output at the mine during 1984. Higher output was obtained owing to an increase in underground ore production, which was partly offset by a reduction in opencut tonnage, as well as to modifications in the recovery circuit. Rate of recovery increased from about 15% to over 82% of the gold contained in the ore and from about 40% to 45% of the contained silver.

Jan 1, 1986

By Karl R. Becker

Detonators representing a sampling of various domestic commercial delay detonators were fired at various direct-current (dc) firing levels. Results of firings using well-below-recommended firing levels showed marked increases in delay times above the nominal values. There was also a marked increase in variation, to the extent that out-of-sequence firings would be essentially assured in any typical blasting round at these low firing levels. Within the range of recommended levels the effects of current increases were not considered to be of great importance relative to other overriding effects, such as the significant difference noted in average values of detonators from different lots having the same nominal delay. This effect, when combined with the normal variation noted among members from the same lot, would cause out-of-sequence firings with detonators from a neighboring delay period. Where comparisons with results from another study were possible, it was found that both studies observed quite similar variations in delay times about the average values, and a lower probability of out-of-sequence firings for the shorter delay period groups. The criterion of the previous study for assessing the likelihood of observing out-of-sequence firings, when applied to the Bureau of Mines data, properly identified two neighboring delay period groups where out-of-sequence firings would occur.

Jan 1, 1981

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982

By Raja V. Rarnani, Robert L. Frantz

"The Generic Mineral Technology Center for Respirable Dust (GTCRD) was created at The Pennsylvania State University and West Virginia University by a congressional initiative in 1983 responding to recommendations in the 1980 National Academy of Sciences study on the Measurement and Control of Dust in Mines. Many of these recommendations dealt with the need to initiate focused fundamental research for further professional progress in dust control. Long-term, sustained support was emphasized to develop expertise in respirable dust research. In creating this Center, Penn State and West Virginia University were specifically recognized for their expertise in and facilities for research on coal mining and medicine. Today, the Center includes the Massachusetts Institute of Technology, the University of Minnesota, and the Michigan Technology University. The Respirable Dust Center is the only organization that coordinates and integrates the medical, scientific, and engineering aspects of respirable dust disease. The Center works with the U.S. Bureau of Mines (USBM), Mine Safety and Health Administration (MSHA), the National Institute for Occupational Safety and Health (NIOSH), the United Mine Workers of America (UMWA), and the U.S. coal industry in defining the research priorities for the programs of the Center to enhance research synergism.The Center's mission is to enhance the health, safety and productivity of miners by advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs to reduce the incidence and severity of respirable dust disease.All Dust Center activities are focused to be responsive to this mission, which is shared by the several federal agencies closely associated with the GTCRD. While significant progress has made mine atmospheres cleaner and healthier, respirable dust-related disease remains the nation's most pernicious industrial hazard.The goals of the GTCRD were formulated with recognition of the diverse scientific, engineering, and medical aspects of respirable dust, in addition to a need to enhance researcher interaction, as well as education and technology transfer efforts, in the respirable dust area. These goals reflect the needs of the mining industry as determined by the National Academy of Sciences Committee on Measurement and Control of Respirable Dust study done in 1980. The report of this committee encouraged the Bureau of Mines to redirect its research efforts ""...toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust."" The GTCRD's goals, detailed in chapter three of this document, were formulated to mesh with NAS recommendations."

Jan 1, 1995

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

Provide a means through which members of the mining community can easily and readily access information on human factors/ergonomics as it relates to mining. Approach As part of a research study aimed at reducing human error accidents in mining the Bureau of Mines developed a computerized information retrieval system which provides relevant human factors or ergonomics information on 19 mining-related special interest categories.

Jan 1, 1988

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

Lower the respirable dust expo-sure of longwall mine workers by reducing the amount of air-borne respirable dust generated during coal extraction. Approach Increase the moisture content of the coal seam through water infusion before the coal is mined. How Water Infusion Works Increasing the moisture content in coal tends to prevent respirable dust from becoming air-borne during mining and transport. The moisture content of the coal seam can be increased by infusing water into the seam. Water under pressure is forced into the cracks (cleats) of the coal seam through sealed bore-holes. The effectiveness of water infusion is a function of the amount of water the coal seam accepts (its infusibility), which depends on the cleat density (cleat spacing) and cleat size (crack diameter). Thus the effect of water infusion on dust control depends mainly on coal seam characteristics. Water infusion techniques are generally used to restrict the flow of methane gas to the working face; however, the technique provides an alternative dust control method in mines with severe dust problems which limit production.

Jan 1, 1987

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985

By R. A. Friedel

Data on compositions of natural substances are important in the study of possible interrelationships. The similarity of the low molecular weight alkane isomers from crude oil and Fischer-Tropsch catalytic synthesis product has been reported (8).3 A similar composition for the alkane isomers from high-temperature coal carbonization has been found. The composition of the C4 to C 7 alkane isomers from these three sources can be calculated quantitatively with the equations previously developed to calculate alkane isomers in Fischer-Tropsch product. An KM sting reversal of the concentrations of the monomethyl isomers from C6(2 Me > 3 Me) to C7 (3 Me > 2 Me) occurs in all three products; fragmentary comparisons at higher carbon numbers indicate some dissimilarities. Naphthene isomers in the C6 to C7 range for crude oil and high-temperature coal carbonization also have similar compositions. Aliphatic hydrocarbons from low-temperature coal carbonization processes are considerably different, consisting mainly of normal alkanes.

Jan 1, 1968

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

Reduce spillage hazards and contamination when adding hydraulic nil to mining machine reservoirs. Approach An easily transported module, that delivers hydraulic oil directly into mining machines, was built and tested. How It Works The Hydraulic Oil Delivery Module is carried, from the oil storage area to the equipment needing oil, in the bucket of a scoop or other utility vehicle. Oil is pumped into the module reservoir from storage, or out of the module reservoir into the machine being serviced, through a long hydraulic hose. During long-term testing, the 115 foot long delivery hose made it possible to replenish the hydraulic oil in mining machines at the face with only limited interruption to the mining operation. (Figure 1 shows one! version of the module.) The compact Hydraulic, Oil Delivery Module consists of: an oil reservoir: a pump driven by a hydraulic motor; two high pressure, low volume oil lines, filters; and a low pressure, larger capacity delivery hose equipped with quick-connect-couplers. The high pressure oil lines are connected to the scoop's hydraulic power takeoff, which supplies the power to pump oil in or out of the module reservoir.

Jan 1, 1977