Search Documents

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By Roy Greenfield

During the detection phase, several procedures can be used to improve the signal-to-noise ratio (SIN) . • Subarrays of up to 10 seismometers should be used. The apparent failure to obtain improvement in SIN in the Westinghouse subarrav work is probably due to excessive noise in the electronics. The spacings needed for sensors in the subarray must still be established. • The sensors should be buried. Even burial to a few feet will probably give appreciable reduction of noise. A deeper burial will probably further reduce the noise; and, if the seismometers can be put below the weathered layer, the signal level will probably be increased. The reduction in noise by burial will be especially effective during high noise periods due to wind or rain. • Before attempting detection, the waveforms should be bandpass filtered. The bandpass should go from 25 Hz to an upper frequency of 100 to 200 Hz. Further measurements with a low noise system must be done before the signal-to-noise ratio can be determined for the 100 to 200 Hz range. Any narrow band noise should be removed by notch filters. • If noise levels differ among seismometers of a subarray, weights inversely proportional to the noise power should be applied to the seismometers. • Automatic methods of screening data for possible signal arrivals should be developed, but the final determination that the signal on a subarray output appears to be from a miner should be made by an analyst. Detection of "signal" on several subarrays should be required for positive identification. In the location phase, after detection: • If repeated signals are received, they should be coherently added (stacked) to give as good a SIN as possible for use in determining signal arrival times, to be used in location computations. The miner should, if possible, repeat the signal 25 to 50 times.

Jan 1, 1974

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

By Alla D. Mah

The energies of combustion of zirconium carbide and hafnium carbide were measured by combustion calorimetry and the heats of combustion and formation. of zirconium carbide and hafnium carbide were derived . The results are-- ZrC AH298.15 ( combustion) = -308.60 ± 0.55 kcal /mole , AH298.15 ( formation) -47.0 ± 0.6 kcal /mole , AH298.15 = HfC (combustion ) = -306.08 ± 0.20 kcal/mole , AH298.15 ( formation) -52.3 ± 0.4 kcal /mole . = INTRODUCTION This report contains the results of calorimetric measurements to obtain the heats of formation of zirconium carbide ( ZrC) and hafnium carbide ( HfC) . The work was conducted as part of a Bureau of Mines program for determining the heats of formation of oxides , carbides , and nitrides by combustion calorimetry . Combustion calorimetry is one of the most precise calorimetric techniques . The chief obstacle to obtaining accurate heat of formation values for carbides , and the chief reason for the variation in the results of different investigators , is the lack of purity of the carbide samples . Corrections for impurities always involve assumptions which lead to uncertainties . In general , a large impurity correction is accompanied by a large uncertainty in the final result .

Jan 1, 1964

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921

By Pablo Velasco

The Ecuadorean mineral sector and overall economy have retained their traditional dependence upon the production and export of hydrocarbon products. Exports of crude oil and its products accounted for 62% of the country's export earnings in 1985. Ecuador's major mineral commodities produced and exported were cement, gold, limestone, liquefied natural gas, liquefied petroleum gas, natural gas, natural gasoline, crude petroleum and condensate, raw steel, semimanufactured steel products, and sulfur.

Jan 1, 1987

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

Avoid accidents that can occur when applying belt dressing from an aerosol can, particularly when can pressure has dropped or when spraying against wind. Approach Use a garde-type sprayer. How It Works Commercially available garden-type sprayers can be used for applying conveyor belt dressing from 12 feet away, or more. Pressure is easily raised and maintained at about 50 psi. Most sprayers have a hand pump, but a battery-powered cordless model is also available. Garden-type sprayers are available in various sizes from 11/2 to 18 gallons, with the larger models wheel mounted. The 3-gallon model evaluated by the Bureau has a shoulder carrying strap, which gives additional safety advantages. Use of the strap frees both hands for climbing ladders or holding onto catwalk rails. When spraying, one hand can remain on a handhold to lessen the chances of touching a moving belt.

Jan 1, 1980

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987