Search Documents

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By R. D. Leitch

"INTRODUCTION This report is another of the series on the effect of drouth and low water on the pollution of streams by coalmine drainage. A previous report3 dealt with work on Bennett Branch of Sinnanahoning Creek, Pa. This report deals with the results obtained during a similar study of Black Lick Creek, Two Lick Creek, and Yellow Creek. All of these belong to the same drainage system. Two Lick Creek is a tributary to Black Lick Creek, and in turn Yellow Creek is a tributary to Two Lick Creek, as shown in Figure 1.Black Lick Creek was of such a volume that a seasonal investigation was not entirely feasible. Yellow Creek was found to have mines only near the mouth, except a few of status unknown to the writer at the extreme head-waters, and the stream was also more or less inaccessible for regular and frequent sampling. Two Lick Creek was found to be most suitable of the three.ACKNOWLEDGMENTThe work reported has been carried on under the direction and with the advice of Dr. R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station."

Jul 1, 1931

By Raymond M. Stateham

Climatic conditions are compared with roof fall occurrence from April 1, 1972, to December 31, 1975, by the Bureau of Mines. These comparisons indicate that humidity has a strong influence on roof fall occurrence rates. Cubic regression techniques are used to develop best fit curves. Statistical analysis of these curves indicate that both are sinusoidal and exhibit positive correlation with each other. The sine waves have a period of 1 year with maximum and minimum inflection points in August and February.

Jan 1, 1978

By David F. Gearhart, Thomas M. Barczak

This U.S. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (9 compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 1992

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By Joseph M. Pugliese

The U.S. Bureau of Mines has produced a generic in situ copper mine design manual, which contains a computerized cost model for in situ copper oxide mining. The model specifies (1) site-specific parameters, which must be quantified for mine design, (2) a method for minesite design based on those parameters, and (3) a procedure for assessing economic viability for the mine design. The menu-driven computer program performs calculations for developing commercial mine design specifications, as well as capital and operating costs. The default values are based on 1986 dollars, and indices for updating costs are included. The program also provides discounted-cash-flow rate of return (DCFROR) and allows for sensitivity analyses for an in situ mining operation at any specific undisturbed copper oxide deposit. This report is to be used with the 1990 version of the computer program, which has been made user friendly. It describes the flies, tutorial, input phase, help function, and monitor display of all calculated values and of the DCFROR table. The monitor-displayed discounted initial value of investment and annual operating costs are defined. The dual rate-of-return situation and sensitivity analyses are also briefly discussed. Information is provided on obtaining the computer program on diskette.

Jan 1, 1991

By A. V. Petty

In accordance with its objective to maximize minerals recovery from secondary domestic resources, Bureau of Mines conducted research on recycling chrome refractory wastes. Since 20 pct of the U.S. demand for imported chromite is used in the production of refractories, primarily for the steel, copper, and glass industries, samples of used chrome-containing refractories from copper converter and reverberatory furnaces were investigated to determine their potential for recycling. The samples were beneficiated using a combination of wet magnetic separation, flotation, and leaching techniques, and the concentrates were reformed into briquets for refractory evaluation. Small refractory test specimens produced from the beneficiated concentrates gave modulus of rupture values at 1,350° C comparable to those of commercial mag-chrome brick of similar composition; however, grinding the waste refractories to at least minus 65-mesh was required in order to liberate the metallic copper. Most of the copper was easily recovered using conventional beneficiation techniques, but the finely ground chrome concentrate would require briquetting, calcining, and crushing to produce a coarse grain suitable for recycling into secondary mag-chrome refractories.

Jan 1, 1981

By E. Chin

Natural gas was Bangladesh's only significant exploited mineral. A few other minerals or mineral-based commodities were produced for local consumption. The most valuable were nitrogen fertilizer, salt, cement, and clay for brick.2 The most important mineral industry development of 1987 was the start of modest production of crude oil, the first discovered and produced in the country. PRODUCTION AND TIADE Production of natural gas from the nation's huge reserves continued to increase but was limited by the lack of residential and industrial demand. Gas reserves of 7 trillion to 16 trillion cubic feet were sufficient for far more production than the country could efficiently utilize for many years. The country's consumption-to-reserves ratio was one of the lowest of the developing nations. Mineral exports have been insignificant, comprising a small amount of nitrogen fertilizer. Nitrogenous fertilizer exports could become important when planned new capacity comes on-stream. Mineral imports were dominated by crude petroleum.

Jan 1, 1989

By Walter R. Storms

This paper , which describes the mining methods and costs at the Atwood copper mine in the Lordsburg ( Virginia ) Mining District of Hidalgo County , N. Mex . , is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices , methods , and costs in various mining districts of the United States . The mine and surface plant are situated in the west half of sec . 7 , T. 23 S. , R. 18 W. , about 3 miles by road southwest of the center of Lordsburg , near the old abandoned townsite of Valedon ( see fig . 1 ) . The main line of the Southern Pacific Railroad passes through Lordsburg , as does the paved eastwest U. S. Highway 70-80 . A spur line of the Southern Pacific ends near the mine . A good graded road connects the mine with Lordsburg . The following pages present a brief history of the district , describe the geology , and outline methods of prospecting and exploration, including sampling and estimations of tonnages and values . Development, and mining methods are explained , and transportation , ventilation , drainage ,. safety measures , and organization are described . The wage scale and costs of development and mining comprise the corrcluding sections of this circular .

May 1, 1949

By S. H. Ash

"INTRODUCTION Mine fires have occurred since underground mining of minerals began, and they are still occurring. The technical literature is replete with papers relating to mine fires.Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents require the collection and analyses of samples of the atmospheres surrounding the fire. Such atmos¬pheres are complex mixtures of gases (1, 3, 4, 15, 21, 23).3/SUMMARYExperiences at mine fires (1, 3, 4, 15, 21, 23) have proved conclusively that mine-air analyses furnish the only means of judging what is going on in a mine fire area. Mine-air analyses give evidence of conditions that require immediate protection, govern the order and control the manner in which a fire is fought, show the necessity of bulkheads and establish the places to construct them, indicate whether or not a fire is being controlled or is being extinguished, and govern procedure in sealing and unsealing mine fires.It is commonly believed that danger to life and property from mine-fire atmospheres is greatest in coal mines; this is true only to the degree that the explosion hazard is greater in coal mines than in noncoal mines because of the presence of combustible gases. The problem of gas poisoning is greater in noncoal mines because of the more frequent occurrence of poisonous and innocuous gases, oftentimes the lack of controlled ventilation, and usually greater difficulties in sealing mine-fire areas. Sulfide minerals present a serious hazard in many metal-mine fires when sulfur dioxide is formed. The country rock or ore body itself may contain or be limestone, which may be calcined. Emanations of carbon dioxide are found."

Dec 1, 1950

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

[ ]

Jan 1, 1997

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982

By Steven M. Shope

An essential element of the Bureau of Mines electromagnetic location and communication system for trapped miners is a quantitative knowledge of the surface and above-surface electromagnetic fields created by an underground transmitter. The field solutions given in this report use approximations in which the displacement currents are negligible for low frequencies. The earth is represented by a homogeneous half-space model in which a dipole source is immersed. The vertical magnetic field equipotential contours at and above the surface are graphically mapped. The volumes of the regions bounded by these contours are directly related to the geometrical zones of signal detectability. Knowledge of the detectability zones will enable the proper search strategies to be developed for airborne detection of trapped miners.

Jan 1, 1983

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

By K. Kar, M. Gautam, J. T. Jurewicz

The 10-mm Dorr-Oliver cyclone has been widely used as a personal sampler for size selective sampling of particles within the respirable range (Dp < 10 gm). Because of their inertia, the particles are unable to follow the swirling flow (outer vortex) within the cyclone. The particles migrate to the bottom of the cyclone, depending on their size, and get trapped into the inner vortex which leads to an eventual blow-off from the top of the cyclone. By measuring the size distribution of the particles in the free stream and in the collected sample, the aspiration efficiency of the cyclone can be calculated. Velocity difference between the free stream and sampling velocity. Inlet orientation, particle impaction and deposition, particle inertia and free stream turbulence result in the departure of the aspiration efficiency from unity and this, in turn, leads to inlet bias. Although the effect of inlet bias on sampling efficiency has been investigated in past, the results lack detailed information and show only some general trend. In this effort, a systematic, in-depth experimental work on the effect of inlet bias on the sampling efficiency has been undertaken using non-intrusive Laser Doppler Anemometry (LDA), Aerodynamic Particle Sizer (APS) and impactors.

Mar 1, 1992

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By J. J. Geraghty

U.S. Bureau of Mines researchers investigated the development of an innovative transport system for underground coal mining. A one-half commercial-scale bench model was constructed. Novel magnetic levitation (mag-lev) technology was developed. Frictionless and contact-free transport of a prototype materials container and payload has been demonstrated.

Jan 1, 2010