Search Documents

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau's efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By R. A. Franks, J. C. Edwards, L. Yuan

To determine the critical air velocity for preventing smoke rollback, diesel-fuel fire experiments were conducted in the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory’s Safety Research Coal Mine. Such information is necessary for preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 to 300 kW depending on the fuel tray area. Airflow in the 2-m- (6.6-ft-) high, 2.9-m- (9.5-ft-) wide coal mine entry was regulated during the course of each experiment. The airflow was measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor and was recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light-obscuration monitors, ionization smoke sensors and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics fire dynamics simulator.

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Stanley K. Haines

This Bureau of Mines publication comprises 19 tables of data concerning domestic barite production and consumption, imports, and world production for the years 1880 to 1976. Barite is vital to the petroleum industry, with 90 percent of domestic consumption used in drilling muds. Domestic production has traditionally fallen short of consumption: in 1976, 41 percent of the 2.2 million tons consumed was imported. World production of barite increased from 269,000 tons in 1923 to 5.2 million tons in 1975 but is in danger of falling short of future demand. The compiled data provide a comprehensive base of information.

Jan 1, 1978

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By E. R. Maize

[In %-port of Invcstiptionn 7452 ,g dcniing with roof ~wet,ent in the Cmcibla r~ine, rof&apos;erence .,as m.da to the f~ct tiwt timker decny war, bsing studied at tho tine of writing. Thic napor, written a3er completion of that ~tudy, describ~s t1l.e ~mrl&apos;: and sunlharizea the fiats obtained. Ifhen tlle stu* oi roof novement bras be,- at Cxcible tw igeas \%.ere a6-r;incsd. on decay of tiriber Q: scne of :he olficialr;: (I.) 9:la.t timber decay v:as unustmlly rapid in ,tho Ciuoiblc mins, ,m?. ((2) that timber coated with rock ri..~st deixiyad morrl mpirlly thnn those %hat vsrc not so coated. Thsx ::ore no records by which tkeso &apos;iaeas could &apos;L;e tertcc?, ard it cnpsarefi vise to make a limite6 in- vo3tiption, p~.rticu!.ai.ly of +.he effect of roc!< dusting on decny, as rock ductirg is nn importnnt mer-ns of ~rc-,rcnt?;~g cad-dust eql-osions. ]

Jan 1, 1941

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950&apos;s; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By James Westfield

Following is a brief resume of the Division&apos;s activities that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1961

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.