Search Documents

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By H. R. Shell

The systems MgO-MgFa-SiO2, at 2 and 4 weight-percent Li2O and at 3.8 and 7.7 weight-percent Na2O were investigated by solid state reaction at 1,200° C. The results are summarized in four ternary diagrams. Besides the expected humites and simpler silicates or fluorides, proto-amphibole and water-swelling fluormicas or fluormontmorillonoids were found in the systems containing lithium and monoclinic fluoramphiboles, water-swelling fluormicas or fluormont-morillonoids, and nonwater-swelling fluormicas were found in the systems containing sodium. These latter compounds were not in the base system MgO-MgF2-SiO2.

Jan 1, 1962

By W. R. Huff

Yield stress and plastic viscosity values, determined from shear rate-shear stress relationships, were found to be a linear function of coal concentration for coal-water slurries containing 40, 45, 50, and 55 weight-percent of powdered coal. In the laminar region, the flow is described by an equation derived from the fact that the square root of the shear stress varied linearily with the square root of the shear rate. In the turbulent region, the friction factor was found to be inversely proportional to the velocity to the 0.12 power.

Jan 1, 1965

By Thomas M. Barczak

he stiffness characteristics of longwall shields were investigated in this Bureau of Mines study. Since longwall strata activity is characterized by roof-to-floor and face-to-waste displacements, a model with two degrees of freedom was used to describe the load-displacement relationship of the shield structure. The model considers the support as an elastic body and relates horizontal and vertical resultant forces acting on the support to associated displacements as a function of the stiffness of the support structure. Stiffness coefficients under full canopy and base contact configurations were determined by controlled displacement loading of longwall shields in the Bureau's Mine Roof Simulator (MRS). Three two-legged longwall shields of different manufacture were investigated. The stiffness characteristics of these shields were evaluated relative to two parameters, namely, shield height and setting pressure. The test results indicate a reduction in shield stiffness for increasing height. Setting pressure was found to have less of an effect on shield stiffness, producing only a slight increase in stiffness as setting pressure increased. Similar trends were observed for all three shields, indicating a similarity in stiffness characteristics for shields of the same basic configuration.

Jan 1, 1988

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By J. F. Barkley

As part of the work of serving as Chairman of Subcommittee 3, Health and Industrial Requirements, of the American Society of Mechanical Engineers' Committee on Air-Pollution Controls, the author assembled the following information on accepted maximum permissible concentrations of air pollutants from the standpoints of health, damage to vegetation, damage to property, and requirements of industrial processes. A search in technical literature was made followed by direct inquiry to all State governments as to their regulations. The subcommittee membership - G. D. Clayton, senior sanitary engineer, Public Health Service, United States Department of Health, Education, and Welfare, Detroit, Mich., Dr. L. Greenburg, commissioner; Department of Air Pollution Control, New York, N.Y., Dr. M. Katz, Defence Research Chemical Laboratories, Ottawa, Ontario, Canada, and Dr. H. H. Schrenk, research director, Industrial Hygiene Foundation of America, Inc., Mellon Institute, Pittsburgh, Pa. - reviewed the information and made very helpful comments and corrections.

Jan 1, 1954

By A. W. Khair, S. J. Jung

"A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.1. INTRODUCTIONMuch research in the past has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in cutting process. However the mechanisms of energy dissipation or failure criteria for rocks in cutting process in order to evaluate the efficiency of energy requirements in specific rock fragmentation is not well understood. The formation of a crater in rock under the impact blow of a bit has been observed experimentally (Hartman, 1959). It is known that directly beneath the edge of the bit the rock is crushed into fine powder, toward the sides of the crater it chips out into relatively large fragments. (Sikarskie & Cheatham, 1973). Singh et al. (1967) investigated the cratering process under the two different conditions of static and dynamic loading. They found that the amount of energy consumed per unit volume of crater is unequal for the two different loading conditions. A complex network of fractures often extends downward and laterally into the rock below the bit. The surface of the specimens showed that the dynamic loading damaged larger area then the static loading."

Jan 1, 1989

By Owen W. Terry

During the summer of 1943 the Bureau of Mines conducted an investigation and program of churn drilling on the McIlhon and adjoining Pearson land in the Mineral Point district of Iowa County, Wis. Sixteen holes, aggregating 1,570 feet .of bore, were completed. The work was undertaken as part of a general investigation of the zinc-and lead-producing area of southwestern Wisconsin at a time when great effort was being made to increase the production of Metals important to the war program. The Bureau's drilling program supplemented a previous drilling pro-gram conducted by the Vinegar Hill Zinc Co., and demonstrated the presence of a strongly mineralized zone at relatively shallow depths.

Jan 1, 1948

By Oliver Bowles

[In an endeavor to promote greater efficiency in the lime industry, the United States Bureau of Mines is preparing a series of preliminary reports dealing with particular problems of the industry. Through the circulation of these reports, it is hoped that sufficient interest may develop among lime-plant operators to prompt them to discuss with the bureau their our experiences with these problems. By such an interchange of ideas, it is believed that conclusion may be reached which will be of practical benefit to try entire industry. The first report, "Stripping problems it Limestone quarries of the Shenondoah Valley", Serial No. 2401, was issued during October, 1922. This report t is the second of the series. It is hoped that may operators will contribute additions to the information now at hand.]

Jan 1, 1922

By P. L. Woolf

Oil was successfully injected into the tuyeres of the Bureau of Mines experimental blast furnace. Determinations were made for the minimum oil addition necessary to permit the maximum available blast temperature of 2,250° F. and the maximum oil rates at blast temperatures of 1,900°, 2,000°, and 2,100° F. From these tests, the upper and lower levels of high-temperature heat input, which limit the smoothly operating furnace, were established. Substantial coke saving was realized with maximum oil injection. Oil-to-coke replacement ratios have been calculated for various conditions, and oil is compared with natural gas and moisture in somewhat general terms. A study of the effect of variations in slag volume and basicity on the sulfur content of the metal at high sulfur loads was made.

Jan 1, 1963

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK – ALTMETER SURVEY WITHOUT PLTTMETER TEMPERATURE CCRRECTION DATA INPUT

Jan 1, 1977

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By Walter R. Storms

This paper, which describes the mining methods of the Potash Co. of America in Eddy County, N. Mex., is one of a series being prepared by the Mining Branch, of the Bureau of Mines on mining practices and methods in various mining districts of the United States. 4, T. The mine and plant of Potash Co. of America are situated in sec. 20 S., R.. 30, E.,. N. M. P. M., about 22 miles by paved road northeast of Carlsbad (fig. 1). A spur line of the Atchison, Topeka & Santa Fe Railroad also connects the mine with Carlsbad.

Apr 1, 1948

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By S. D. Maksimovic

The Bureau of Mines identified and evaluated major sources of quartz dust during overburden drilling at a surface coal mine, The relative contribution of each source to the total dust hazard was estimated, using personal gravimetric and instantaneous dust-sampling devices. No attempt was made to determine actual dust generation rates. The major sources of dust at the drill rig during dry drilling opera-tions were the collector dump, drill shroud leakage, and drill stem seal leakage, These sources contributed 90 pct of the respirable dust and 89 pet of the respirable quartz dust generated during drilling, The collector dump cycle (21.6 pct of total drilling time) accounted for 38 pct of the respirable dust and 41 pct of the respirable quartz dust, with peak dust concentrations reaching 68 mg/m3. Shroud and drill stem leakage contributed 28 and 24 pct of the respirable dust and 32 and 16 pct of the respirable quartz dust, respectively. A dragline and second drill rig contributed the remaining 10 pct of dust and 11 pct of quartz dust. Gravimetric dust samples collected inside the drill cab and outside, near the cab door, averaged 1.65 and 1.43 mg/m3, respectively, with 6 pct respirable quartz.

Jan 1, 1985

By Michael D. Fenton

Bauxite resources were primarily in Africa, Asia, Oceania, and South America. Only five countries combined, Australia, Brazil, Guinea, India, and Jamaica, contained most of the total world reserves available for extraction under current economic conditions and accounted for nearly 80 % of world production of bauxite. World bauxite and alumina production declined and prices for smelter-grade alumina remained below the $200/mt level during 1993 because of growing aluminum inventories on international markets and declining worldwide demand. The United States imported bauxite primarily from Australia, Brazil, Guinea, and Jamaica. U.S. alumina plant capacity remained essentially unchanged throughout 1993, but apparent capacity utilization decreased by the close of 1993. Chromium Most of the world's known resources and reserves of chromite are located in India, Kazakhstan, South Africa, and Zimbabwe. India, Kazakhstan, and South Africa accounted for 73 % of world production of chromite. The two largest producers of chromite, Kazakhstan and South Africa, were in the process of major economic and political change during 1993. South Africa's production and exports of chromite continued to fall during 1993, because of weak international demand and a flood of cheap metal from the former U.S.S.R. and China into world markets. Despite a significant increase in production, South Africa's ferrochrome producers continued to operate below capacity in 1993. Prior o the dissolution of the U.S.S.R., Kazakhstan was a major internal supplier of chromite ore to the U.S.S.R. consumer, but subsequent decline in demand led to a downward trend of chromite production in Kazakhstan and increasing exports to Europe during 1992 and 1993. The United States consumed, about 10% of world chromite ore production in various forms of imported materials. The United States imported nearly one-half of its required chromium contained in chromite ore and chromium ferroalloys and metal from South Africa; the remainder was from the minor producers Turkey, Yugoslavia, Zimbabwe, and others.

Jan 1, 1995

By D. Cummins

This Information Circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery manufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

Jan 1, 1980