Search Documents

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By W. H. Ode, W. A. Selvig

In 1938 , the Bureau of Mines cooperated with Subcommittee XV on Plasticity and Swelling of Coal ( C. C. Russell , chairman ) , of Committee D-5 on Coal and Coke , A.S.T.M. , by testing various methods for determining expansion and plastic properties of a series of coals of widely different coking properties . One of the tests made by the Bureau was the British Standard Method for the Crucible Swelling Test for Coal.5/ Briefly , this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties .. The number of the standard profile with which the maximum cross -sectional area of the button most nearly corresponds is recorded as the swelling index . Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization , it gave indications of having value in measuring free - swelling and caking properties of coals when burned on fuel beds . An opportunity to investigate this occurred when an engineer of an eastern public utility 'company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal . Some of these coals gave trouble by swelling 'excessively and clogging the grates . Samples were ob- · tained , and it was found that the troublesome coals gave decidedly higher free -swelling numbers than did the coals that performed satisfactorily . Also , it was found that the free - swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the · ´`standard volatile -matter test or from agglutinating - value results . The results of the free - swelling tests were considered by the Subcommittee on Plasticity and Swelling , and a special group of the subcommittee , under the chairmanship of R. A. Sherman , was delegated to study the test method . Ostborg , Limbacher , and Sherman , ofthe Battelle Memorial Institute , ' investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential -type stokers from the standpoint of the coking characteristics of the coal . Data were presented also showing that the indexes wer helpful in the selection of coal for industrial underfeed stokers .

Oct 1, 1946

By Byron O. Pickard

With table of bibliography

Sep 1, 1922

By Launa Mallett, Charles Vaught, Kathleen M. Kowalski, Michael J. Brnich

This paper reviews research from the U.S. mining community to define issues relevant to an evolving national and international workforce and to relate them to the emergency response population. The authors further explore and relate the key problem of an aging workforce to the resultant changes and emerging physical and psychological needs of emergency workers. Finally, the authors cite examples from the mine emergency response community and mine rescue experiences to suggest practical recommendations that include both organizational and individual formats, with an emphasis on new approaches to training this changing workforce.

By H. R. Babitzke

The purpose of this investigation was to evaluate the potential of columbium-hafnium alloys as structural materials for use at elevated temperatures. The work described in this report was conducted to determine the properties of columbium-hafnium alloys and to select the more promising ones for further improvement. Properties determined in this report were machinability, hardness, workability, tensile strength, and oxidation resistance. Ten ingots, ranging from 100 percent columbium to 70 atomic-percent hafnium, were prepared and subjected to tests. The test results showed that the alloys with 33 and 50 atomic-percent hafnium were superior in workability, strength, and oxidation resistance. For the alloy series tested, the strength and hardness values increased with the increasing hafnium content. Maximum values were reached with 50 atomic-percent hafnium. The oxidation resistance was poorest at the 1 atomic-percent hafnium level but improved with increasing hafnium content through 70 atomic-percent. Eight of the ten ingots were fabricable at room temperature. The two remaining ingots, those with 5 and 10 atomic-percent hafnium, required hot-working.

Jan 1, 1962

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By E. P. Youngman

The mining laws referred to by those who furnished the reports mentioned in the preceding paragraph are : General Austrian Mining Law of 1854 and the Law of 1868 , which prescribes for Hungary (as well as for Transylvania ) the full text and decisions of the General Austrian Mining Law; Government Decree 18346 , 1859 ; Parliamentary Decree of 1861 ; the Law of 1871 ; the Commercial Code , Law 37 of 1875 ; the Industrial Lar of 1884 ; the Law of 1386 ; the Decree of the High Court of Justice , 5540 , of 1399 ; Laws 6 and 7 of 1911 ; Law of 1921 ; Laws 23 and 24 of 1922 ; Laws 5 and 21 of 1927 ; and Law 40 of 1928. ( Lev 21 of 1927 and Law 40 of 1928 are labor laws . ) A compilation of the mining laws of Hungary , " Magyar Banya Jog , " or the " Hungarian Mining Law, " was made use of in part . This volume is the second edition of a school textbook , which ras prepared by Dr. Bela Balkay and Dr. Imre Szeoke , and which was published by the Apollo Press ( V. , Sas -utca 13 , Budapest ) in 1909 .

Jun 1, 1931

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

By C. M. Frost

The hydrodesulfurization characteristics of a Venezuelan topped crude oil and a Venezuelan reduced crude oil were determined at temperatures from 740° to 850° F, pressures from 800 to 1,600 psig, and space velocities from 1.0 to 2.0 Vo/Vc/hr. Kinetic calculations showed that under these conditions the desulfurization reaction was first order with respect to sulfur and had an average activation energy of 32.5 kcal/mo1. Catalyst life tests made at 750° F, with pressures of 800, 1,200, and 1,600 psig and space velocities of 1.0 and 1.25 Vo/Ve/hr, showed that the decrease in the relative activity of the catalyst was a logarithmic function of time or volume of oil processed and the amount of vanadium deposited on the catalyst. Comparative tests made with residual fuels prepared from a Wilmington, Calif., crude oil and a Wyoming asphaltic crude oil showed that catalyst life may be extended by processing fuel oil with a low metal content, but it may be shortened by the presence of large amounts of asphalt in the feed.

Jan 1, 1971

Develop a dry dust collector suitable for working faces and belt transfer paints. Approach A filter cartridge with a reverse-pulse, self-cleaning system has been mounted in-to a low profile unit requiring electric power only. How It Works Dust-laden air entering the in-let end of the collector passes through the two inline filter elements. When the elements load to a pre-selected pres-sure drop, they are automatically pulse-cleaned by a "backflush" method using compressed air. When the elements are pulse-cleaned, caked dust material on the filter surface is released, and falls away as lumps. Dust is removed from the collector by an auger mechanism. Features of the collector are: (1) unit is completely self-contained, (2) built-in air compressor for pulse-cleaning, (3) cleaning cycle initiates automatically at a preset restriction, (4) automatic auger discharge of collected dust, (5) detachable extension auger for transporting collected dust, (6) "dust leak" indicator light, and (7) "change filter element II warning light. The collector has been designed as permissible although approval has not yet been granted.

Jan 1, 1981

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By F. W. Jones

The perturbation of alternating electromagnetic fields by three-dimensional structures is considered. The general model is that of a semi-infinite conducting half -space which consists of regions of different conductivities. A numerical method is used to obtain the solution for the equations and boundary conditions. The effects on the fields at the surface of the half-space due to the conductivity discontinuities are shown by three-dimensional amplitude and phase plots.

Jan 1, 1973

The Crow Indian Reservation is located in the southeastern part of Montana, stretching from near Billings, in the center of the state, to the Wyoming border in the south. The Office of Surface Mining's Casper, Wyoming, Field Office is responsible for regulating mining and reclamation on Crow tribal land. Federal legislation enacted July 11, 1987, authorized the Indian tribes to implement approved Abandoned Mine Land Reclamation Programs. In early 1988 the Crow elected to develop an Abandoned Mine Land Program under the Title IV provisions of SMCRA. The tribe's plan received final approval on January 4, 1989.

Jan 1, 1992

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991