Search Documents

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Doris M. Hyde

The Government of Belize maintained strict control over spending in 1982 as a means of protecting its import-dependent economy against the effects of a general worldwide recession. The modest economic performance was not expected to differ substantially from the $152 million2 gross national product (GNP) estimated for 1981. Exports and reexports were expected to decline in 1982, partly as a result of the Mexican peso devaluation. Imports were also expected to decline slightly in 1982, but the overall trade deficit was projected some-what higher than the $44 million experienced in 1981. On September 21, 1982, Belize became an independent state. As a result, the new Government became eligible for assistance from international organizations such as the International Monetary Fund, the International Bank for Reconstruction and Development (World Bank), and the United Nations Development Program (UNDP). Belize's independence from its former status as a colony of Great Britain was marred somewhat by the unsettled territorial dispute between Great Britain and Guatemala. Guatemala declared Belize was a part of Guatemala and. therefore. refused to recognize it as an independent state. Negotations between Great Britain and Guatemala continued without resolution.

Jan 1, 1984

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Howard W. Wainwright

The Bureau of Mines is engaged in a research program on the characterization of tars produced by low-temperature carbonization of coal and their economical upgrading to more valuable materials, Throughout the years, hydrogenation has played an important role in the treatment of these tars, mainly as a means of converting the whole crude tar or selected fractions to motor fuels; diesel oil, lubricating oil, or various solvents. In some instances, production of specialty chemicals has been the objective. The purpose of this report is to summarize, without critical review, the information of the past 25 years on the hydrogenation of low-temperature tars and related substances as presented in the literature or its English translation. Published articles and patents not abstracted in the main body of this report are included in a bibliography at the end. HYDROGENATION REACTIONS The hydrogenation of tar follows three general types of reactions; 1. The removal of oxygen, sulfur, and nitrogen in the tar to form water, hydrogen sulfide, and ammonia, respectively: [ ]

Jan 1, 1961

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 mil-million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious.

Jan 1, 1934

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By E. L. Litchfield

The electrification of ammonium nitrate-fuel oil (AN-FO) blasting agents by pneumatic loaders is described and discussed. The consequences of the electrification are considered in light of the initiation requirements of electric blasting caps. It is recommended (1) that semiconductive loading tubing be utilized and (2) that the resistivity of the AN-FO be controlled; it is further recommended that the operator (3) test to assure continuity of the electric detonator legwire-bridgewire-legwire circuit prior to insertion of the cap into charge or borehole, (4) keep the legwires shunted but not otherwise connected to ground during loading of the blasting agent into the borehole, (5) assure that the borehole is discharged prior to hooking up the detonator leads, (6) assure that he is himself discharged prior to handling the detonator leads, and (7) assure that the blasting cap leads are never carried to the AN-FO loader. The basis and significance of these recommendations are explained.

Jan 1, 1968

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981