Search Documents

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By G. M. Potter, S. J. Hussey, R. Havens

The Artillery Peak manganese ores , from one of the largest known manganese deposits in the United States , present a difficult problem in concentration because they are low-grade and the association of manganese and gangue minerals is intimate and complex. The known size of this deposit has justified investigation of processes such as leaching, wherein preliminary enrichment of the original feed might be advantageous .. Therefore , the ore-dressing studies on Artillery Peak ores were carried on with the object not only of making directly marketable manganese products but also of removing acid-consuming calcite and raising the grade of ore for leachingplant feed . Owing to the extent of the deposits , test work was carried on at the Salt Lake laboratories in considerable detail on several lots of ore of varying composition . This paper summarizes the results obtained from laboratory testing of four samples obtained by engineers of the Mining Branch from the Maggie Canyon area of the Artillery Peak deposit . Also included are results obtained from testing one sample of Chapin Group ore , which was considered representative of numerous very low-grade ores submitted from the Artillery Peak district . During the course of the investigations , many data were obtained and compiled , but for the sake of brevity , data of secondary importance have been omitted or condensed and only those tests giving the more pertinent results are discussed in detail ...

Nov 1, 1947

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau's mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By Sidney Katell

This report is an economic evaluation of the production of hydrogen in a continuous system by the steam oxidation of partially reduced iron oxide in a fluidized bed at 7 atmospheres using producer gas to reduce the iron oxide. The oxidation-reduction step is based on experimental data obtained by the Bureau of Mines at the Pittsburgh Coal Research Center. The estimated capital requirement for a plant producing 30 million std. c.f.d.3 of 99.8 percent purity hydrogen at a discharge pressure of 450 p.s.i.g. is $13,100,000, using January 1961 equipment cost data. Based on a 330-day operating year, the operating cost before profit and taxes with coal price as a variable is estimated to be:

Jan 1, 1962

By J. B. Zadra, J. M. Gomes, Don H. Baker

Electrolytic deposition at 1,000 ° C in an electrolyte essentially consisting of 7 parts sodium pyrophosphate , 2 parts sodium chloride , and 1 part sodium tetraborate yielded tungsten of 99.9 percent purity . Scheelite concentrates containing 25 to 73 percent WO, and varying quantities of iron , lime , and silica were used as feed materials for the electrolysis . The metal contained less than 0.01 weight - percent each of iron , calcium , silicon , aluminum , carbon , and oxygen . Modification of the electrolyte permitted deposition of equal - quality metal from scheelite concentrates containing higher quantities of iron , calcium , and silica . The electrolytic separation of molybdenum and tungsten was accomplished by minor variations in the operating procedures .

Jan 1, 1964

By Paul T. Allsman

This paper describes metal- mining practices at the Harrington -Hickory lead - silver - zinc mine at Milford , Beaver County , Utah . The operations of the Harrington-Hickory incorporate a number of features that should prove of interest and value to other operators of small mines . These features include employee participation in profits , a well- laid -out electrical system, adequate financing , a well - balanced equipment and supply inventory , a well - organized system of bookkeeping , adequate roads , and good management . As crude ore is shipped directly to smelters and mills in the Salt Lake Valley , close attention is paid to see that the ore is segregated by classes and treated where it can bring the greatest not return . A combination of these features has resulted in maintaining relatively low costs, considering the grade and size of ore shoots at a time , during and following the war , when equipment , supplies , and labor were costly and difficult to obtain . The period covered in this report includes two war years and two years following , from April 1, 1944 to June 30 , 1947 .

Apr 1, 1949

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety lamps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By John S. Berber

Tar produced as a byproduct from low-temperature carbonization of coal contains only small amounts of valuable lower boiling tar acids but relatively high percentages of high-boiling tar acids. These high-boiling tar acids are characterized by a high degree of alkylation and can be converted into the lower boiling homologs by catalytic treatment to remove the alkyl groups or decrease their chain lengths.

Jan 1, 1965

By Peter G. Kovalchik

To compare the viability of the new fuse wire arc test (FWAT) as a substitute for the comparative tracking index (CTI) for determining surface resistance to electrical tracking, the Bureau of Mines constructed a fuse wire arc tester and undertook a detailed testing program for testing insulating materials used on explosion-proof enclosures. This report describes the Bureau&apos;s apparatus, the two methods (CTI and FWAT), and the results of the Bureau&apos;s testing, showing comparisons of the FWAT with the CTI. Results showed strong correlation between the two methods, as all specimens tested that had CTI ratings of 400 V ac rms and above passed the 10-test sequence with the FWAT, whereas all specimens with lower CTI ratings failed, with the number of tests to failure corresponding roughly to the descending CTI rating order.

Jan 1, 1987

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By J. G. Groetsch

Municipal solid waste (MSW) contains about 8 pct ferrous metallics which are typically recovered by magnetic separators at municipal resource recovery facilities. At present, only about 182,500 ton/yr of MSW magnetics are being processed for remelting out of the -11 MMton/yr discarded. The Sn in MSW magnetics makes this material difficult to recycle to the steel industry. An electrolytic method using stannous fluoborate-fluoboric acid for removing Sn was evaluated. Optimum concentrations of Sn in the electrolyte and the effects of impurities such as Al, Cu, Fe, and Pb on Sn recovery from the electrolyte were evaluated. Operating parameters were 60 to 65 g/L fluoboric acid and 20 to 30 g/L Sn using stainless steel electrodes at a current density of 60 A/ft2. Tests were run with postconsumer scrap4 and MSW magnetics. Good results were obtained with MSW magnetics, after pretreatment by reshredding, magnetic separation, and air classification. The final Sn content of the MSW magnetics scrap was reduced from 0.18 to 0.017 wt pct. Heat and solvent treatments of MSW magnetics to remove coatings did not significantly improve Sn removal beyond that obtained with material that had only been mechanically pretreated.

Jan 1, 1984

By John C. Feeley

This paper is the result of a field study of prospect drilling in the Florida phosphate fields. The objective is to describe the drilling methods employed . . Since the general policies of the operating companies in the land - pebble area do not permit the dissemination of prospecting information and costs thereof , the writer has carefully avoided mentioning names and locations except by reference to existing publications ,

May 1, 1949

By B. B. Letson

The heats of formation of lithium chloride and lithium oxalate were determined with the aid of a Bureau-developed, glass Dewar-type solution calorimeter which uses thermistors as its temperature sensing element. Values obtained at 298.15° K were -98.38 ± 0.54 kcal/mole for lithium chloride and -329.02 ± 0.79 kcal/mole for lithium oxalate, using graphite as the standard state for carbon.

Jan 1, 1965

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976