Search Documents

By Ted C. Briggs

Equations for the elastic pressure distortion of the volumes of a Burnett compressibility apparatus are developed and presented in this report for volumes under internal and external applied pressures. An experimental method for the determination of the external pressure distortion coefficients is presented. Young?s modulus and the internal-pressure distortion coefficients are computed from the experimentally determined external-pressure distortion coefficients. The temperature dependence of the pressure distortion coefficients and of Young's modulus is evaluated for the temperature range 0° to 80° C.

Jan 1, 1968

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By Gerald R. Smith

Because of continuing concerns regarding the effects of cumulative quantities of materials in the environment, the Bureau of Mines has initiated a series of studies to evaluate, to the fullest extent possible, all aspects of the materials flow sequence fur selected commodities. Although tungsten and its compounds do not pose a significant health hazard to the environment, they do represent valuable resource materials to which appropriate conservation considerations must be given. The present study includes a description of recent trends in the consumption, loss, and recycling of tungsten-containing materials in the United States during the period 1974 to 1991 and an estimation of the cumulative loss of tungsten to the environment since 1910. Obsolete tungsten is recycled primarily as cemented tungsten carbide components that have been used in cutting and wear-resistant applications. The quantity recycled, as a of annual U.S. consumption of tungsten, was estimated to have increased from 10% in 1974 to 341a in 1991. An estimated 58% of the 148,000 metric tons of primary tungsten consumed since 1910 was lost to the environment through means such as dissipation, discard, and dilution.

Jan 1, 1994

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

In laboratory tests using reconstructed soil columns, rubber latex showed good sealing efficiency when applied at a rate equivalent to 4000-5000 pounds per acre. Results of field testing, however, were inconclusive. The ideal situation in which latex would coagulate in a narrow zone two to three feet below the surface by reacting with acidic or metallic constituents of the soil was not attained. Rather, the latex was deposited progressively as it passed through the soil (most of it remained in the top foot), the rate of deposition being dependent on soil structure and composition as well as on properties of the latex such as particle size and emulsion stability. Latex stability appears to be a more critical property than latex particle size in controlling penetration. Addition of excess anionic or nonionic surfactants to latex improved its penetration into the soil. A styrene-butadiene (SBR) rubber latex of 2400 Å average particle size with high mechanical stability gave the best balance of penetrating ability and sealing capacity in laboratory tests and this was confirmed in tests on a 5 x 5 foot test plot at Lanse, Pennsylvania. This latex was subsequently applied to three one-quarter-acre plots at Lanse by sprinkler irrigation, and compared to adjacent areas that were sprinkled with water only. Soil moisture measurements did not enable us to judge the effectiveness of the seal because differences between sampling positions were greater than differences between treated and untreated sections, but permeability tests showed that water flow was much slower (90-99% reduction) within the top ten inches of soil in the latex- treated sections. This sealing effectiveness was reduced after wintering. There was no deleterious effect on the vegetation as a result of sprinkling the areas with latex. A laboratory study conducted in a 5 x 5 x 5 foot box containing uniform reconstructed soil from a New Jersey source suggests that latex penetration into the soil in the field occurs mainly through natural macro openings and not through the capillaries of the soil structure. Dilute solutions of ammonium hydroxide or sodium carbonate (with no latex present) were found to seal effectively in laboratory soil columns as well as in field applications. However, since these chemicals are water soluble, the seal is temporary. Raw material costs of latex at the application rates used in the field testing are in the order of $1000 per acre. Equipment and operating

Jan 1, 1972

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By D. T. Hahn

Adequate and cost effective erosion control is an important component in most plans for reclamation of surface mined land. Despite the fact that much is known about erosion of agricultural lands, insufficient conclusive knowledge is available about erosion of reclaimed surface mined land. Our study was conducted to characterize the erodibility of reclaimed surface mine land relative to unmined cropped land, and to evaluate the accuracy of the universal soil loss equation (USLE) in estimating erosion from reclaimed soils. A rainfall simulator was used to measure runoff and erosion rates from plots at three Indiana surface mines. The relation of erosion of the reclaimed soils was not completely constant with that from the cropped soils. Significant differences in erodibility were observed between reclaimed and nonreclaimed top soils, as well as reclaimed topsoils and reclaimed subsoils.

Jan 1, 2011

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966